Bumpers & Trim

These hard rubber bump strips attach to the front bumper guards with 2 studs from the back side. Extreme care is needed prior to attempting to remove them. If you force the nut from the backside you will dislodge the stud from the rubber. For best results use a small wire brush on the studs first and soak liberally with a product like PB Blaster. Sold individually, right is the same as left, Ford Casting number as found on the back is D1WB-17A812-AB

This option includes paying a core charge. By choosing this option, the re-chromed item you receive will have started the re-chroming process as an average quality core.We highly recommend that you send us your core first. Here's why: We can core match your bumper guards. Bumpers guards that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the...

This option includes paying a core charge. By choosing this option, the re-chromed item you receive will have started the re-chroming process as an average quality core.We highly recommend that you send us your core first. Here's why: We can core match your bumper guards. Bumpers guards that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the...

This options includes the core charge, but there are advantages of sending cores in advance:Advantages of Pre-Sending Cores: - We core match your Bumper Guards. We recommend you pre-sending your core if you have a good quality core, as our A grade Bumper Guards are always reserved for core matching. If your core is not a grade A core, you may be able to pay a charge to upgrade to a higher grade re-chromed Bumper Guards.- Ships after we receive and inspect your Bumper Guards core, avoiding...

This option includes paying a core charge. By choosing this option, the re-chromed item you receive will have started the re-chroming process as an average quality core.We highly recommend that you send us your core first. Here's why: We can core match your bumper guards. Bumpers guards that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the...

Rear bumper guards and all the parts needed to install rear bumper guards on your 1967 - 1968 Mercury Cougar. Kit Includes:2 Rear Bumper Guards that have been triple plated to a level far beyond NOS standardsthe mounting kit consists of:a reproduction pair of bracketsnew fasteners. Mounting diagram not included, if you need one CLICK HERE for a printable version. No core exchange is required for this purchase. *NOTE* As is often the case, service replacement parts are painted and the...

This option includes paying a core charge. By choosing this option, the re-chromed item you receive will have started the re-chroming process as an average quality core. We highly recommend that you send us your core first. Here's why: We can core match your bumper guards. Bumpers guards that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the...

This option includes paying a core charge. By choosing this option, the re-chromed item you receive will have started the re-chroming process as an average quality core. We highly recommend that you send us your core first. Here's why: We can core match your bumper guards. Bumpers guards that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the...

D3WY-17A820-A This is one of the end brackets that mounts the outer bumper shell to the bumper beam. "L" shaped bracket, most have a stamped number of 4928A01 on them. Sold individually, 2 needed per bumper.

Reproduction Bumper Retainer for the 1967 - 1968 Mercury Cougar or Ford MustangSold individually 

C9AZ-13A164-B Inner grille bushing, where the hidden headlight hinge pivots. Hole size is 3/4", shaft size is 1/2". Fits many of the Ford, Lincoln, Mercury cars with vacuum headlight covers. List includes 1969-71 Full size Ford Galaxie, LTD, XL, Country Squire, and Mercury Marquis, Brougham, and Monterey. Lincoln Continental starting in 1970 until? 1972-? Lincoln Mk IV. Also select Cylcone / Fairlane / Torino 1970-71 any with hide away headlights.

Used outer bushing for the hinge pivots for the hide-away headlights on the Mercury Cougar. Hole size is 5/8", shaft size is 3/8". Fits many of the Ford, Lincoln, Mercury cars with vacuum headlight covers. List includes 1969-71 Full size Ford Galaxie, LTD, XL, Country Squire, and Mercury Marquis, Brougham, and Monterey. Lincoln Continental starting in 1970 until? 1972-? Lincoln Mk IV. Also select Cylcone / Fairlane / Torino 1970-71 any with hide away headlights. Ford part # C9AZ-13A164-A. ...

Hardware for mounting the hood bumpers on the radiator core support. Clip mounts with threads down, nut on top. Sold as a Kit as Pictured.

D1WY-17A914-A Rear bumper center beam, mounts on top of the bumper brackets behind the rear bumper.

D1WY-17B883-A Bracket that mounts under the reinforcing beam, lower center bumper mounting point.

C9AZ-13B013-A Center section that connects to the vacuum motor on many 1969 Ford and Mercury cars with vacuum covered headlights. 1969 Mercury Cougar including XR7 and Eliminator. The center piece is offset to the left of center and the hook part that goes to the vacuum motor points down. 1969 and 1970 center shafts are not interchangeable. 1969 Ford LTD 1969 Galaxie and Galaxie XL 1969 Country Squire Wagons 1969 Mercury Marquis 1969 Mercury Brougham 1969 Marauder and X-100 1969 Colony Park...

D0WY-13B013-A Center section that connects to the vacuum motor on 1970 Mercury Cougar, including XR7 and Eliminator. The center piece is offset to the left of center and the hook part that goes to the vacuum motor points down.1969 and 1970 center shafts are not interchangeable.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

This check valve is located in-line just behind your carburetor. To test it simply place it in your lips and try blowing through the side with the single port. You should be able to breath in and not breath out. If this valve is bad you will find the headlights opening up after the engine has been shut off on your 1969 - 1970 Cougars and your tilt away function not working correctly on your 1967 - 1970 Cougars equipped with a tilt column. A good working vacuum system should be able to...

Used 1968 Mercury Cougar GT-E horizontal grille bar clip or keeper for the center grille section. This is a rare find, limited to stock on hand.

Reproduction clip for attaching the 1969 front fender extension moulding / trim and the 1970 hood moulding / trim found on the Mercury Cougar. The 1969 application calls for 2 of these clips along with 1 larger clip per side. If you need the larger clip for the 1969 front fender extension moulding / trim, you can get'em right here. The hood lip brightwork for the 1970 requires 4 per side.  *NOTE* The threaded stud on this clip is a little longer than the original ones. This...

This trim clip is a little larger than the original C4GB-6242364-A retainer assembly Ford used and looks a little different, but will work just fine for the front extension mouldings. This will also suffice as a good substitute for the 46 clips used on the 1968 GTE side moldings. Sold Individually.Length: 13/16" from lip to lip.

This fragile little clip attaches to the bottom outer edge of the front fender extension and holds the tail of the aluminum eyebrow moulding to the extension, one per side. They almost always fail when you remove them, and to be honest, we rarely have them in stock. We do not list these hard to find parts to tease you, but rather for documentation purposes. We do offer a nice reproduction clip that you can get right here that will work great. ...

Used clip for attaching the moulding / trim to the front fender extension on the Mercury Cougar. Three of these clips (with long studs) are used per side to attach the 1970 aluminum extension moulding / trim. We do not currently offer a proper reproduction for this clip. We do have this reproduction clip here and it will work for the top positions, but the stud is to short to work on the lower portion of the fender extension moulding / trim. *NOTE* Some 1970 Cougars used 2 of the 1969...

Used front fender extension moulding / trim clip for the Mercury Cougar. This is the largest of the three clips required to attach the aluminum 1969 fender moulding / trim to the extension. One is used on each side at the tail (larger part) of the trim piece. This unit is for the purest. If originality is not as important to you, you can get the inexpensive reproduction here.

Used clip for attaching the front fender extension moulding / trim on the Mercury Cougar. The fender extension moulding / trim is sometimes called the eyebrow moulding / trim. This piece of brightwork requires a total of 3 attaching clips, 2 smaller clips and one larger. If you need the larger clip, you can get'em right here! This used original clip is for the purest who values originality. If originality is not an issue, you can get our inexpensive reproduction clip here and save a...

Reproduction large moulding / trim clip for the rear quarter extensions and front fender extensions on the Mercury Cougar. The molding / trim on the 1967-68 rear quarter extension and 1969 front fender extension both require 2 different sizes of clips to properly hold them in place. For the 1967 and 1968 rear quarter extensions, you will need one of these large clips and 1 smaller clip per side. For the 1969 Cougar you will need 1 of these larger clips along with 2 smaller clips per side. This...

Reproduction clip for attaching the hood lip moulding / trim on the Mercury Cougar and six are required. We do offer good used originals here for the purest, but these will work great at half the cost.

Used hood lip moulding / trim clip for the Mercury Cougar. This unique little clip is found only on the 1969 hood lip moulding and six are required to mount your aluminum hood trim. Be forewarned, there will be varying degrees of surface rust found on these used clips and will rarely look mint. These units are high dollar and are for the purest whee originality is of the utmost importance. If originality is not an issue, you can get our inexpensive reproduction clip right here and save a...

Used hood lip moulding / trim clip for the Mercury Cougar. Ten of these clips (five per side) are required to mount the two aluminum "L" shaped hood lip mouldings to the 1970 hood. These clip are for the purest who places a high value on originality. If originality is not an issue, you can get our inexpensive reproduction clips here and save a little of that hard earned money.

Reproduction clip for the rear quarter extension moulding / trim on the Mercury Cougar. The rear quarter extension moulding / trim uses 2 different size clips. This is the smaller of the two. One per side, 2 per car. Get the larger clip here. Replaces Ford part # C7WB-65291B80-A. *NOTE* Will work with the 1967-70 trunk trim, but the nuts are wrong style.

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

Used clip to attach the rear deck / trunk lid moulding / trim on the Mercury Cougar that comes with a reproduction cadmium plated acorn nut. Seven of these clips were used to mount the anodized aluminum 1967-68 trunk lip moulding / trim to the trunk. These clip can also be found on some early 1969 Cougars with a stainless steel deck moulding / trim. This used clip is for our type "A" personality purists that insist on having the original part, even though nobody will ever see it. If ultimate...

Used clip for the stainless steel rear deck / trunk lid moulding / trim for the Mercury Cougar. This clip will also work on the 1967-68 aluminum rear deck / trunk lid moulding / trim. Seven of these units are required per moulding / trim and the acorn nut will have some rust on it. If originality is not a issue, you can get our reproduction clip here and save a little of that hard earned income. For more insight on this tricky trunk trim, check out our video below: ...

Used rocker moulding end clip. Fits all 1968 Mercury Cougars. This clip is plastic and metal, it has a stud which goes through the body of the car. sold individually, 4 total needed per car. Our all metal version of this clip is reproduced and is a better value. Find it here.Ford part number C7OZ-6221094-A.

Correct plastic rocker moulding clips with Ford engineering # C9WB-6510182-A, Ford part #C9WY-6510182-A. There are five of these on each side for a total of ten per car. These same clips can be found on 1977-1979 Mercury Cougars and Thunderbirds. Most likely they were used on other FoMoCo products. If you know of other applications where these clips can be found let us know so we can post the information to help others in their search. Sold Individually.

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This particular clip is used on many Ford cars throughout the 60's and 70's.This listing is for a box of 100 clips. We recommend buying...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

Aftermarket clip for attaching the long black plastic rear bumper filler on any 1971-73 Mercury Cougar. A total of 8 clips are needed to attach the rear bumper filler. Most have either broken with age, or have broken during the removal of the filler. Sold individually.

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission. Replaces Ford part number C4ZB-17450-C.

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.

Sold as a set of twelve (two more than required), replaces Ford part #C9WY-6510182-A. From the factory there were five of these on each side for a total of ten per car. These same clips were also used on 1977-1979 Mercury Cougars and Thunderbirds. Most likely they were used on other FoMoCo products.Fits: 1969 Mercury Cougar1970 Mercury Cougar

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

Set includes ten rectangular clips with pop rivets and two incorrect, irregular shaped end clips (Mustang Part). These clips will fit the 68 Cougar, but are actually replicas of the clips for the 67-68 Mustang. Rather than the plastic end clips in this kit, we recommend the metal version that we sell separately. NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to...

This is the sub-kit you would have received when you purchased a stainless steel service replacement deck moulding for your 1967 - 1970 Mercury Cougar. The original clips used with a 1967 - 1968 aluminum deck lid moulding would have been similar but would have had a plastic shell surounding the metal clip. For more insight on this tricky trunk trim, check out our video below: ...

Reproduction aluminum shift indicator console overlay for the Mercury Cougar or Ford Mustang. Although a brushed finish is correct, this reproduction has a coarser brush stroke when compared to the originals and is a bit dull.  We recommend a quick polish to make them look closer to the finish of the originals. These fit well, and unless you put them up against an original, it is hard to tell the finish is slightly different. This installs around your console...

We have a hard time finding and keeping grade A "near mint" front fillers on our shelves. Driver side (left hand) part number is C7WY-16304-B and the casting (or engineering) number imprinted on the part is C7WB-17B957-B. The Mercury MPC refers to these as "anti squeak pads." Sold individually, not as a pair.*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The part you will receive will be "as taken from a parts car" and will need...