Bumpers & Trim

We have a hard time finding and keeping grade A "near mint" front fillers on our shelves. Driver side (left hand) part number is C7WY-16304-B and the casting (or engineering) number imprinted on the part is C7WB-17B957-B. The Mercury MPC refers to these as "anti squeak pads." Sold individually, not as a pair.*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The part you will receive will be "as taken from a parts car" and will need...

This is the grade “B” driver side (left hand) front bumper corner filer and is what we find on the majority of our parts cars. These used hard rubber parts will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch. Steel wool is a good way to clean them up and boiling them in water before install can often times make them appear less warped. These look better than the reproductions in our opinion and will cost you less money. Driver side part number...

We have a hard time finding and keeping grade A "near mint" front fillers on our shelves. Passenger side (right hand) part number is C7WY-16304-A and the casting (or engineering) number imprinted on the part is C7WB-17B951-B. The Mercury MPC refers to these as "anti squeak pads." Normal 0 false false false EN-US X-NONE X-NONE Sold individually, not as a pair.*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The part you will receive will be...

This is the grade “B” passenger side (right hand) front bumper filler and is what we find on the majority of our parts cars. These used hard rubber parts will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch. Steel wool is a good way to clean them up and boiling them in water before install can often times make them appear less warped. These look better than the reproductions in our opinion and will cost you less money. Passenger side part number...

Far better quality than the reproductions. The driver side (left hand) has a C7WY-16304-C Ford part number and the casting (or engineering) number imprinted on the top of the driver side part is C7WB-17B957-A. The Mercury MPC refers to these as "anti squeak pads." Sold individually, not as a pair*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The part you will receive will be "as taken from a parts car" and will need cleaning. Sold...

Sold individually. This grade "B" filler is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch, maybe even a factory blem has been found that will drop it to a grade "B" level. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This (albeit less than perfect) looks better than the reproduction in...

Far better quality than the reproductions. The passenger side (right hand) has a C7WY-16304-D Ford part number and the casting (or engineering) number imprinted on the top of the passenger side part is C7WB-17B951-A. The Mercury MPC refers to these as "anti squeak pads." Normal 0 false false false EN-US X-NONE X-NONE *NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The part you will receive will be "as taken from a parts car" and will need...

Sold individually. This grade "B" filler is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch, maybe even a factory blem has been found that will drop it to a grade "B" level. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This (albeit less than perfect) looks better than the reproduction in...

Reproduction pair of rubber front bumper corner fillers for your 1967 - 1968 Mercury Cougar. These install horizontally in the upper portion of your front bumper corners. Good used originals have become very hard to come by and that's why we've partnered with Daniel Carpenter to make these high quality reproductions. Do not confuse these with the previous inferior reproductions from a different supplier. Sold as a pair. Replaces Ford part #'s C7WB-17B951-B and C7WB-17B957-B ...

Reproduction pair of rear bumper corner fillers for the 67 - 68 Cougar. The Mercury MPC refers to these as "anti squeak pads."  Replaces Ford part numbers: Driver side - C7WY-16304-C                                            Passenger Side - C7WY-16304-D

This 2 1/4" trim part installs directly above the steering column.

This 2 1/4" trim part installs directly above the steering column.

When removing this part resist the temptation to "open it up". Instead walk it off carefully leaving it in its factory position.

When removing this part resist the temptation to "open it up". Instead walk it off carefully leaving it in its factory position.

This unique to 1967 standard Cougar dash trim set is what outlines the gauge cluster face pad. It is unique to the 1967 standard Cougar as it is held in place by black Phillips Screws. The 1968 trim set is held in by clips. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent.

This unique to the 1968 standard Cougar trim set is what outlines the gauge cluster face pad. It is unique to the 1968 standard Cougar as it is held in place by spring clips. The 1967 trim set is held in by Phillips screws. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent. *NOTE* The spring clips that hold this trim to the dash bezels is very hard to come by. We usually have a few in stock but you may want to consider installing your dash...

Used aluminum face pad moulding / trim four piece set for the Mercury Cougar.

This unique to the 1968 standard Cougar trim set is what outlines the gauge cluster face pad. It is unique to the 1968 standard Cougar as it is held in place by spring clips. The 1967 trim set is held in by Phillips screws. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent as shown here. *NOTE* The spring clips that hold this trim to the dash bezels is very hard to come by. We usually have a few in stock but you may want to consider...

This trim part starts to the upper left of the gauge cluster and continues on to the passenger side following the line of the upper padded dash.

This trim part starts to the upper left of the gauge cluster and continues on to the passenger side following the line of the upper padded dash.

Only for use on standard model Cougars with no A/C. This piece of trim affixes to the lower portion of the dash face pad and continues on towards the passenger side door.

Only for use on standard model Cougars with no A/C. This piece of trim affixes to the lower portion of the dash face pad and continues on towards the passenger side door.

Only for use on standard model Cougars with AC. This piece of trim affixes to the lower portion of the dash face pad and continues on towards the passenger side door.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used dash face pad for the standard Mercury Cougar that is NOT equipped with air conditioning. This unit will be nice and will not have any cracks, but could use a reproduction emblem and a coat of good vinyl paint to make it look great. We recommend SEM brand vinyl paint, you can get black here or parchment here. If you need a different color, find your local autobody supplier. They should be able to mix up a small amount of the exact color you need. This icon means that we're looking to buy...

This rectangular trim part is located on the right side of the glove box on all 1967 - 1968 Mercury Cougars without factory installed AC. This could be referred to as a passenger side AC vent block off plate. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as-is for a driver quality car. We cannot promise we will have your color in stock but we will try to accommodate your request of color.

Reproduction Center Grille Insert Background Decal for the 1967 and 1968 Mercury Cougar. This insert will need to be shaved down on 2 sides to fit correctly, do not force the insert into the grille, it will pooch up in the middle and not adhere correctly. The aluminum Mercury Man emblem can be popped out from the rear with a solid hit with a drift punch and hammer without causing damage. Check out our video below, showing how to install this decal, along with some other handy grille...

Nice reproduction that is "almost" spot on. Of the two versions available this one has much more definition. When you put an original next to this reproduction you will notice the original has a more raised, defined face on the Mercury Man.

This restored trim piece mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Driver side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21547-A. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

This restored trim piece mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Passenger side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21546-A. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

This was originally a 6 piece set for both the Convertible and Coupe. It could be ordered as a stand alone or part of the protection package which included door edge guards, bumper guards and floor mats. The door strip is the longest and can be cut to fit the fenders or quarter panels.

Used driver side (left hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

Used passenger side (right hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

NOS, new old stock, Stainless steel clip on guards for the rear edge of the 1967 and 1968 Cougar doors. Would have been part of the exterior decore option. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. Ford part number C7WY-6220910-A.

Stainless steel clip on guards for the rear edge of the 1967 and 1968 Cougar doors. Would have been part of the exterior deccor option. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. These used trim parts will have many very small dings and scratches. The driver side moulding will have substantially more damage than the passenger side moulding. Ford part number C7WY-6220910-A. NOTE: This item will not ship until useable cores are received. ...

C7ZZ-652220-B Restored, stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Passenger side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind. *Note - Excludes Mustang fastback and convertible.

This restored driver side (left hand) drip rail moulding / trim for the Mercury Cougar equipped with a vinyl top has had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. These are sold outright, as one side only, or as a pair. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good used...

This restored passenger side (right hand) drip rail moulding / trim for the Mercury Cougar equipped with a vinyl top has had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. These are sold outright, as one side only, or as a pair. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good...

These look great and because they have the correct anodized finish they will not get dull like a part that has only been polished will.Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you still have questions about your cores, check out the video below. ...

Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...

These 1969 eyebrow mouldings have always been very sought after. Due to their exposed location they often times are mangled or missing. The better the core you provide, the better end product you will receive. If the core needs a lot of work the end result is they end up being thin which of course means they are more prone to future damage. If you have extra cores we would be happy to apply a credit towards your purchase. This purchase requires that you first send us your core. New eyebrow...

If you do not have a core that is worthy of restoration we have them for sale.Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. For more info on aluminum trim restoration & core exchanging, check out our video below. ...

This conversion will replace the old, tired, vacuum system that likes to leak and wear out. This kit consists of two electric actuator assemblies (new Mazda Miata motor) with a plug and play wiring loom for easy installation. Simply remove all existing vacuum components and replace with this kit to have headlight covers that work under any conditions with the car running or not. These new motors are smoother and more reliable than previous versions that utilized the Ford Probe motors and are...

This conversion will replace the old, tired, vacuum system that likes to leak and wear out. There are few differences between the 1969 and 1970 conversion kit. This kit consists of an electric actuator assembly (new Mazda Miata motor) with a plug and play wiring loom for easy installation. Simply remove all existing vacuum components and replace with this kit to have headlight covers that work under any conditions with the car running or not. These new motors are smoother and more reliable...

This conversion will replace the old, tired, vacuum system that likes to leak and wear out. There are few differences between the 1969 and 1970 conversion kit. This kit consists of an electric actuator assembly (new Mazda Miata motor) with a plug and play wiring loom for easy installation. Simply remove all existing vacuum components and replace with this kit to have headlight covers that work under any conditions with the car running or not. These new motors are smoother and more reliable...

This pair of tail light bezels have been chemically dipped to remove the chrome and are ready to be painted black for your 1970 Resto-Mod or 1970 ELIMINATOR. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved (mostly on the top edge) before these are paint ready. We hand select premium parts that have minimal defects.If you send cores in for exchange they must be pit free and no...

Used Grade "B" center grille emblem for the 71 - 72 Standard Cougar. Will have fading, pitting and the plastic lens area will need to be restored. Ford part number D1WY-8A223-A

Reproduction center grille emblem background. This decal is only made with the "7", so you will need to remove the "X" and "R" from your existing decal and adhere them to this new one. You can clean those letters up with some extra fine polishing steel wool. The standard grill emblem with a walking cat uses the same stud configuration as XR7 so you can exchange emblems from one to another. ...