General (Old Category Structure)

Spot-On reproduction from WCCC! C8OE-B Application for 1968 includes all 390-2V, 390-4V, 427-4V, and 428 Cobra Jet engines with and without air conditioning. 1969 application is only the S code 390-4V engine, with or without air conditioning. Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. We do sell a Hayden replacement fan clutch. Replaces Ford master part number C8OZ-8600-A. This fan will also work on many small block applications. We hope...

Another spot-on reproduction by WCCC! C9ZE-E Applications: 1. All 1969 428 Cobra Jet with and without air conditioning. 2. 1969 428 Super Cobra Jet with V code 3.91 axles only. 3. 1970 428CJ with air conditioning and some without air conditioning (see your build sheet if available). Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. We do sell a Hayden replacement fan clutch. Replaces Ford master part number C9ZZ-8600-C. This fan will...

C8AZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12-5/16 inches long. Alternate number C8AA-7515-B or C8AA-7541-B. Couple of variations of this fork. Most versions will not be stamped. Spring and side holes not needed for Mustang and Cougar applications. Originally for 1968 full sized cars with 289 or 302 engines and manual transmissions. Maybe 6 cylinders, not sure, but vert likely. Cougar 1971 - 1973, 351 Engines. Mustang 1971 - 1973,...

D0DZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Alternate number D0DA-7515-B. Service replacement after 1973 D3DZ-7515-A for Maverick/Comet. Cougar 1970, 351 Engines. Mustang 1970, 250/302/351 Engines. Maverick 1971 - 1972, 250/302 Engines. Grabber Comet 1971 - 1972, 250/302 Engines. GT Fairlane 1970, 250/302/351 Engines. Torino / Ranchero 1970, 250/302/351 Engines. Montego / Cyclone 1970, 250/302/351 Engines. MX, ...

C5OZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 9-1/4 inches long. Specifically used with a 157 tooth flywheel, as opposed to the 164 tooth fly wheel used after Feb 1968.Replaces ford Part # C5OZ-7515-B.  Cougar before 2-15-1968, 289/302 Engines.  Mustang before 2-15-1968, 289/302 Engines. *Note - This style of clutch fork uses the 'wire' for the holder, not the clip. ...

C5OZ-7515-B Manual transmission clutch fork for small block V8 engines - 3 and 4 speed, stick shift transmissions. Fork measures 9-1/4 inches long from the divot where the rod rides to the tip of the forked end. Specifically for the C5DA-6394-A bellhousing that used a 157 tooth flywheel. Cougar 1967 through 2-15-1968. XR7, XR7-G. Mustang 1965 through 2-15-1968. 2+2, GT. Fairlane 1965 through 2-15-1968. 500, XL, Custom. Torino / Ranchero 1968 through 2-15-1968. 500, XL Comet 1965 through...

C8OZ-7515-A Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 10-1/2 inches long. Specifically used with a 164 tooth flywheel, as opposed to the 157 tooth fly wheel used before Feb 1968.Replaces ford Part # C8OZ-7515-A, alternate number C8OA-7541-A.  Cougar after 2-15-1968 - 1969, 289/302 Engines.  Cougar 1969, 351 Engines.  Mustang after 2-15-1968, 289/302 Engines.  Mustang 1969, 250/302/351 Engines.  Fairlane after 2-15-1968,...

C8OZ-7515-A Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 10-1/2 inches long from the divot where the rod rides to the tip of the forked end. Specifically used with a 164 tooth flywheel, as opposed to the 157 tooth fly wheel used before Feb 1968. Replaces Ford part number C8OA-7541-A. Ford casting number C8OZ-7515-A. New reproduction small block fork also available here. Cougar after 2-15-1968 - 1969, 289/302 Engines.  Cougar 1969, 351...

C8OZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12 inches long. Alternate number C8OA-7541-B. Cougar after 2-15-1968 - 1969, 390 Engines. 390IP. Mustang after 2-15-1968 - 1969, 390 Engines. 390IP. Fairlane after 2-15-1968, 390 Engines. Torino / Ranchero after 2-15-1968 - 1969, 390 Engines. Comet after 2-15-1968 - 1969, 390 Engines. Montego after 2-15-1968 - 1969, 390 Engines. ...

Replaces Ford part number C8OZ-7515-D. Manual transmission clutch fork - 4 speed, stick shift transmissions. Fork measures 12 inches long. Alternate number C8OA-7541-D.

C8OZ-7515-D Manual transmission clutch fork - 4 speed, stick shift transmissions. Fork measures 12 inches long. Alternate number C8OA-7541-D. Cougar 1968 - 1969, 428 Cobra Jet engines.  Mustang 1968 - 1969, 428 Cobra Jet engines.  Fairlane 1968 - 1969, 428 Cobra Jet engines.  Torino / Ranchero 1968, 428 Cobra Jet engines. Montego / Cyclone 1968 - 1969, 428 Cobra Jet engines. *Trivia - This fork originally had a blue paint mark for identification purposes. This model clutch fork...

D0OZ-7515-A Manual transmission clutch fork - 4 speed, stick shift transmissions. Fork measures 12 inches long. Alternate number D0OA-7541-A. Designed for the big spline 1 3/8" input shaft toploaders. Cougar 1970, 428 Cobra Jet engines. Mustang 1970, 428 Cobra Jet engines. Torino / Ranchero 1970 - 1971, 429/429CJ Engines. Cobra Montego / Cyclone 1970 - 1971, 429/429CJ Engines.

C8OZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12 inches long. Alternate number C8OA-7541-B. Cougar after 2-15-1968 - 1969, 390 Engines. 390IP. Mustang after 2-15-1968 - 1969, 390 Engines. 390IP. Fairlane after 2-15-1968, 390 Engines. Torino / Ranchero after 2-15-1968 - 1969, 390 Engines. Comet after 2-15-1968 - 1969, 390 Engines. Montego after 2-15-1968 - 1969, 390 Engines. ...

Used until early (prior to 2/15/1968) on manual transmission cars. Comes with rivets. Replaces Ford part #: B9AZ-7522-B.This style uses the early clutch fork with the anti rattle wire.

Clutch Fork Pivot for Cougars manufactured after 2/16/1968. Replaces Ford Part #: C8AZ-7522-A.

Manual transmission clutch kit for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is a 10 inch disk, pressure plate, throw out bearing, pilot bearing, and alignment tool. The clutch disc is asbestos free.

Manual transmission clutch kit for all 1967-69 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 390 engines. This is a 11 inch disk, pressure plate, throw out bearing, pilot bearing, and alignment tool. The clutch disc is asbestos free.

Quality reproduction clutch pedal that works on all 1969-70 Mercury Cougar and Ford Mustangs. Improved design for easier installation.

These clutch pedals feature an improved design (removable pin) for easier installation. Compatible with existing hanger assembly even in automatics. Replaces Ford Part # D1ZZ-7519-B.

C7ZZ-7519-A We also offer used clutch pedals along with our quality reproduction 1967-1968 clutch pedal. These pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

C8ZZ-7519-B We also offer used clutch pedals along with our quality reproduction 1967-1968 clutch pedal. These pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

D1ZZ-7519-B Good used pedal but these pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

Bumper that helps stop the 'clunk' noise when you take your foot off of the clutch pedal on manual transmission 67 - 68 Cougars and Mustangs.Replaces Ford Part Number: C7ZZ-7583

Replaces Ford Part # : D0OZ-7583

This kit has everything you need to repair your clutch and brake pedal and pedal support in one easy kit. Repairs 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Plus many other Ford cars.This kit requires welding. For use on pedal hangers that are all wallered out, or 1971-73 pedal hangers that are not round. Kit has roller bearings. Quality Scott Drake / Holley product. *Hint - All 1967-70 brake pedal hangers have the clutch pedal shaft bushings, even the automatic cars. The originals are...

These reproduction pads are high quality replacements for worn or missing original pads. Replaces Ford part number C9ZZ-7A624-A.

This reproduction stainless trim mounts over your pedal pad. Not only adds style but also holds your pad in place. Replaces Ford part number C5ZZ-7B544-A.

Includes machined pedal shaft, washer and special pin. Replaces Ford Part #: C5ZZ-2478-AK.

Made of heavy gauge steel with a satin black painted finish. Correct threads and hole pattern for 1967 - 1968 Mercury Cougar or Mustang. Replaces Ford Part #: C7ZZ-7535-B.

Made of heavy gauge steel with a satin black painted finish. Replaces Ford Part #: C9ZZ-7535-A.

(7521) Correct contour insures a good fit, 12 1/2" long. This is for both 3 and 4 speed cars. Check out the comparison picture with the off-shore crapola rod sold by most vendors. The only reason you replace this rod is that it is wore down in the area where the bushing seats. Unfortunately when the Chinese were given a sample to copy they must have been given a worn out one! The one on the left (made in USA) fits tight with the bushing and was copied from a NOS sample. Replaces Ford Part #:...

(7521) Correct Contour and fit. Connects pedal to Equalizer bar. Fits all engine sizes 3 and 4 speed. Replaces Ford Part #: C9ZZ-7521-C.

Stainless Clutch Pedal Pad Trim. Replaces Ford Part #: C9ZZ-7B544-A.

Manual transmission clutch throw out bearing for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is with a 10 inch disc.

Sold as pair, exact copy. These also double to keep your windlace firmly in place.

These are the plastic brackets that screw to you roof and then slide the vinyl colored piece over. Sold individually, four are required per car. Replaces Ford part # C8AZ-6229232.

Used to store your shoulder belt above the windlace on the drivers side (harder to find than passenger side). These are often rusty, missing or broken. I am not aware of any reproductions being made.

Sold individually, black only. We have an array of colors in good used condition used. We also have the hard plastic bracket that this slips over. Four are required per car. Replaces Ford Part #: C8AZ-6229024-A.

Used to store your shoulder belt above the windlace on the passenger side. These are often rusty, missing or broken. I am not aware of any reproductions being made.

Fits 1968 - 1973 Standard or XR7

These emblems can be used anywhere from your toolbox, to the dash or trunk and anywhere in between. Makes a great accent to other fender emblems or door panels. Peel and stick.Sold as a pair.

Used 1969 351W coil mounting bracket. This version of the bracket is specific on the 351W and allows extra room for the oil dipstick. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. Listed in the...

Used coil mounting bracket. This version of the bracket is probably the most common. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. This version has the notch as shown. We know that this version was used on...

We will loan this coil spring compressor for 60 days, with a 100% refundable purchase price. This tool now comes with a bearing to make the job much easier. Only available to customers that purchase our front suspension rebuild kits. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Coil spring compressing tool, this is a must for safely removing front coil springs on any 1967-73...

Used driver side coil spring cover, taken from a parts car. Ford part # C7ZZ-3383-A.

Used driver side (left hand) coil spring cover that is a good solid western part for Mercury Cougar and Ford Mustang.Ford part # D1ZZ-3383.

Used passenger side coil spring cover, taken from a parts car. Ford part # C7ZZ-3382-A.

Reproduction driver side (left hand) outer shock tower cover for Mercury Cougar and Ford Mustang. We cannot stand behind this product as it is an ill fitting reproduction, however do offer rust free used originals. No returns accepted.