General (Old Category Structure)

Ford casting number C8AE-6316-C Includes all 1969-70 Q or R code 428SCJ engines or those cars with the drag pak option. Outside diameter is approximately 7-1/2 inches. Ford part number C8AZ-6316-C. Has the timing marks on rim. This is a rebuild service only, your core harmonic balancer will be sent to our rebuilder, allow 3-4 weeks turn around. 3 - 4 weeks after we receive your rebuildable C8AE-6316-C core at WCCC. *Note - Excludes 1969 - 1970 428 non dragpack Cobra Jet engines.Click on images...

ETA FOR THIS ITEM IS 8/23/2023Decent off shore part. Since good used cores are very expensive and almost impossible to find this is often the only choice.

Ford casting number D0OE-6316-B Includes all 1970-71 J or C code 429CJ engines. The D0OE-6316-B harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-5/8 inches, and 1-3/8 inches thick. Ford part number D0OZ-6316-B. Has the timing marks on rim.  Core charge is refundable when rebuildable D0OE-6316-B harmonic balancer is received by WCCC.Click on images to enlarge. This is a picture of a 40 year old piece of rubber...

Ford casting number D0OE-6316-B Includes all 1970-71 J or C code 429CJ engines. The D0OE-6316-B harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-5/8 inches, and 1-3/8 inches thick. Ford part number D0OZ-6316-B. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for those wanting to...

Ford casting number C9ZE-6316-B or C9ZE-6316-C. Includes all 1969 G code Boss 302 engines. Ford master part number C9ZZ-6316-B. Has the timing marks on rim. This is a rebuild service only, your core harmonic balancer will be sent to our rebuilder, allow 3-4 weeks turn around. 3 - 4 weeks after we receive your rebuildable C9ZE-6316-B or C9ZE-6316-C core at WCCC. *Note - Excludes 1970 Boss 302 and all non-Boss 302 engines. Click on images to enlarge. This is a picture of a 40 year old piece of...

Ford casting number D0ZE-6316-A Includes all 1970 G code Boss 302 engines. Ford master part number D0ZZ-6316-A. Has the timing marks on rim. This is a rebuild service only, your core harmonic balancer will be sent to our rebuilder, allow 3-4 weeks turn around. 3 - 4 weeks after we receive your rebuildable D0ZE-6316-A core at WCCC. *Note - Excludes 1969 Boss 302 and all non-Boss 302 engines.Click on images to enlarge. This is a picture of a 40 year old piece of rubber removed from a harmonic...

C9ZE-6316-B 1969 G code Boss 302 Eliminator and Mustang only. Ford casting number C9ZE-6316-C is also acceptable. Outside diameter is approximately 6-1/2 inches. Ford master part number C9ZZ-6316-B. Crankshaft balancer, crank-shaft dampener, harmonic balancer. If you have a rebuildable core 1969 Boss 302 balancer to trade, we can offer a substantial discount off of the retail price.  Notice the rubber on this one is unusually nice. *Note - Excludes 1970 Boss 302 and all non-Boss...

Ford casting number C4AE-6316-A. All 1967 Ford S code 390-4V engines. 1967 (and earlier), 6-5/8 inches in diameter, cast iron construction with key way groove. This is a combination crankshaft balancer and pulley. Has the timing marks on rim. Ford Master Part number C3AZ-6312-E. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for those wanting to keep a 100% original looking...

Very nice reproduction of the D0ZZ-15525-A 1970 Mercury Cougar and Ford Mustang 4 speed backup light wiring harness, with the factory installed Hurst shifters. Plugs into the backup lamp switch and connects to the harness plug on the firewall behind the engine.

Reproduction radio to door harness for your 67 - 70 Cougar or Mustang.

These 1969 molded vinyl, single post head rests were never offered on a Cougar or Mustang to our knowledge but they make a great "go-around" for the very expensive 1968 dual post headrests. To use them on your 1968 Cougar you will first need a pair of 1969 bucket seats as they have the internal hardware to accept the post. 1968 was a weak design so the 1969 seat frame is a nice upgrade and of course will accept any of the 1968 foam and interior kits. These headrests when in the down position...

Nice thick foam. Chromed mounting post. Includes base plate for seat. Keep in mind we have good used for less money, several colors available in good condition. Find them here.

This used header will not be perfect as you can see from the pictures but it can be restored with some TLC. The part you get will be solid, we will not send you junk.Ford casting number C9ZB-76514A72-A

This used header will not be perfect as you can see from the pictures but it can be restored with some TLC. The part you get will be solid, we will not send you junk.Ford Casting Number: D1ZB-76514A72-AA

Reproduction headlamp adjusting nut and screw. Slightly longer screw than stock, small amount of added length does not interfere with anything in or behind the grille. The nut is an exact copy of what is found on the 1969-70 adjustment. Almost the same as the nut found on the 1967-68 Cougar, this isn't even shown on those grilles. 1967-68 mounts on the backside of the headlight bucket. Total of 8 adjustment screws used on each 1967-70 Cougar, item sold individually.Note: When installing...

Screws and spring clips for the tank or reservior for vacuum system

Fits Standard and XR7 Sold as a Kit as Pictured.

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-16A and "H", There are four different versions used, but they are the same for the 1969-70 Mercury Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-37-A and "L", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1967-68, but was moved...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7OB-37B and "RL", There are four different versions used, but they are the same for the 1967 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-37-A. Right hand low beam holder. Ford part...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "L", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used on 1967-68 Mercury...

Used random brand 4001 high beam headlight for the Mercury Cougar. High beam headlights are distinguished by the number 1 at 12 o'clock position and the 2 prong connection on the back. We guarantee these units to work. Basic Ford part # 13007-B.

Reproduction 4001 incandescent (non-halogen) high beam light bulb for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar. Plugs right in to the factory 2-prong plug and mounts in the inboard position on the car.These are OEM wattage (50 watts) to work with the factory headlight switch, without the need to add relays like you would for higher wattage halogen bulbs.Replaces bulb number 4001. Sold individually, 2 required per car.

Reproduction pair of halogen headlights for any 67 - 73 Cougar or Mustang. These bulbs work for both high and low beam, you simply need to bend one of the tabs back for high beam (see photo above). Keep in mind that you will need a headlight relay kit when installing halogen headlights on your car.  Benefits of switching to halogen bulbs: Brighter lightDramatically improves driver visionOptical lens for a powerful beamLong range high powered lightsCrystal clear glass face with H4 halogen...

Used random 4000 or 4002 brand low beam headlight for the Mercury Cougar. Low beam headlights are distinguished by the number 2 at 12 o'clock and the 3 prong connection on the back. We guarantee these units to work. Replaces basic Ford part # 13007-B.

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up.  If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much harder to find outer, low beam lamp distinguished by the number 2 at 12...

Sold as a pair, these were a one year only feature that allows you to quickly disconnect the hideaway headlight vacuum hose kit a few inches from the firewall. The fittings are slightly different so as not to mix up the connection by crossing the lines.

These are the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. They are held in place by a spring and two screws. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight rings side by side. If you look close at...

This is the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. It is held in place by a spring and two screws. Four rings required per car, sold individually. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the 1971-73 Mercury Cougar. Marked C8OB-16A and "H", There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car. Driver side high beam bulb holder any 1971-73 Mercury Cougar.Ford part # C8OB-16A.

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7MB-17A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-17-A. Left hand high beam holder. Ford part # C7MB-17A ...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the 1971-73 Mercury Cougar. Marked C8OB-37-A and "L", There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. Driver side low beam bulb holder for any 1971-73 Mercury Cougar.Ford part # C8OB-37A. ...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7OB-47B and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-47-A.  Ford part # C7OB-47B.

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-16-A and "RH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7MB-16A and "RH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-16-A. Ford part # C7MB-16A.

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "H", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1967-68 Mercury...

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the 1971-73 Mercury Cougar. Marked C8OB-17-A and "H", There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. 1971-73 Mercury Cougar passengers side high beam bulb holder.Ford part # C8OB-17-A. ...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-37-A and "RL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the 1971-73 Mercury Cougar. Marked C8OB-47B and "L", There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. Passenger side low beam headlight holder for any 1971-73 Mercury Cougar.Ford part...

Used set of 4, semi gloss black headlight adjusting rings that hold the headlight bulbs in place on the 1967-70 Mercury Cougar. There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are mostly rust free, taken from a Western parts cars. All four individual headlight holding cups. These are mostly going to have the C8AB part numbers on them, which is what we have the most of. Included is cups...

Used set of 4, semi gloss black headlight adjusting rings that hold the headlight bulbs in place on the 1971-73 Mercury Cougar. There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are mostly rust free, taken from a Western parts cars. All four individual headlight holding cups. 

This option requires you to PRE-PAY a $40 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. ALL GRADE B ACTUATORS COME WITH A 60 DAY WARRANTY. You can find the seal rebuild kit here. Used grade "B" headlight door actuator for your Mercury Cougar. Every once in a while (not often) we will...

Requires you to PRE-PAY a core charge of $30. Used grade "B" headlight door actuator for your Mercury Cougar. This grade B actuator has been reconditioned with new seals but will still slowly leak down after time as not all of them will function as new after being reconditioned. These actuators are sold individually on an exchange basis or outright (for an additional core charge). One actuator actuates both headlight doors on the 69-70. This unit also comes with a 30 day warranty. Ford part #...

This option requires you to PRE-PAY a $40 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. NOTE - If your actuators are the type with the internal spring (Thunderbird actuators had a failsafe internal spring) we cannot accept those as cores. An easy way to tell which actuators are the...

D0OB-13A167-A - NOT FOR COUGAR / GALAXIE. This actuator was removed from a Southern California car years ago and was immaculate inside and had no pitting on the shaft. Starting with a clean core is paramount, if it sounds like a tambourine when you start the process your results will not be very good. The inner shaft seal as well as the dust bellows was replaced using the West Coast Classic Cougar kit. It holds vacuum well on the bottom nipple, but the top (like most) will leak down in...

Pair of reproduction headlight actuators for the 67 - 68 Mercury Cougar. Manufactured to meet and exceed factory specs without the need for additional parts or modification. Keep in mind when you buy these units WCCC will pay $50 for the pair of your rebuildable core units. Our video below explains how to determine if your cores are acceptable. Check out this video on how to rebuild your existing headlight vacuum actuators ...