General (Old Category Structure)

Used bracket for holding relays, either the emergency flasher or turn signal flashe. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This is one of two different brackets used for holding relays or flasher brackets. See our related items.Replaces Ford part number C9ZZ-14A301-A.

Used bracket for holding relays, either the emergency flasher or turn signal flasher. We find these mainly in 1970 Mercury Cougar and Ford Mustangs. This is one of two different brackets used for holding relays or flasher brackets. See our related items.Replaces Ford part number D0ZZ-14A301-A.

Used bracket for mounting the various relays found on 1967 Mercury Cougars, both standard and XR7 models. This bracket mounts under the dash off of another bracket (see 1967 Cougar Electrical Assembly Manual page 15).*Note - 1968 used a different bracket.Replaces Ford part number C7WB-14A301-B.

Used bracket for mounting the various relays found on 1968 Mercury Cougars, both standard and XR7 models. This bracket mounts under the fuse block and is roughly "Z" shaped as shown. *Note - 1967 used a different bracket.Replaces Ford part number C8WB-14A323-D.

Driver side rear mounting bracket for the 1970 Mercury Cougar front fender side marker lights. They will not be bent or heavily rusted. The drivers side has an engineering number of D0WB-15A431-A and the passenger side has the number D0WB-15A**** stamped into it.

Passenger side rear mounting bracket for the 1970 Mercury Cougar front fender side marker lights. They will not be bent or heavily rusted. The drivers side has an engineering number of D0WB-15A431-A and the passenger side has the number D0WB-15A**** stamped into it.

Used trunk plate or bracket for mounting the "J" bolt for the spare tire. Several versions of this bracket, this is the most common one. Mounts flat to the trunk floor surface on all 1967-70 Mercury Cougar hard tops, with full sized spare tires. Additionally, 1971-73 Mercury Cougar convertibles. We cut these out of the trunk floors, so there will be some metal preparation for the customer. Ford part number C7AZ-6247076-A.

Used trunk plate or bracket for mounting the "J" bolt for the spare tire. Several versions of this bracket. Mounts on a corner of the trunk floor surface. 1969-70 Mercury Cougar convertibles, with full sized spare tires. Additionally, 1971-73 Mercury Cougar hard tops. This folded bracket was also used with cars with space saver spare tires, or trunk mounted batteries. We cut these out of the trunk floors, so there will be some metal preparation for the customer. Ford part...

Used bracket for attaching the steering column upper bracket to the brake pedal hanging bracket. Has a slot as shown. Fits all 1969 Mercury Cougar and Ford Mustang with either tilt or fixed steering columns.Shows up in the exploded views as Ford part number 3678.

One year only bracket used on both fixed and tilt column cars.

Used steering column to dash bracket. One year only, used on both fixed and tilt column cars.

Used bracket for mounting a steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Main bracket only, there is also a side support bracket that is also needed. Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick. Tilt and fixed steering columns.Ford part number D0AZ-3676-A.

Used bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Main bracket only, there is also a hooped support bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3676-A.

Lower steering column mounting bracket. 1967-68 Mercury Cougar and Ford Mustang. Right and left halves with original fasteners. Rubber gasket sold separately.Ford part number C7ZZ-65017A50 and C7ZZ-65017A51.

Floor mounting column bracket for the 69-70 Cougar or Mustang. Rubber gasket may not come with bracket, and if it does will most likely need replacing. Undamaged with original fasteners. Get the gasket here.Ford part number C9ZZ-65017A50-A.

Used lower steering column mounting bracket at firewall, for any 1971-73 Mercury Cougar or Ford Mustang. Rubber seal will need to be replaced, see related items for rubber seal.  Ford part number D1ZZ-65017A50-A.

Reproduction concours correct throttle return spring bracket for the Mercury Cougar or Ford Mustang equipped with the 390GT engine. This bracket is shorter in length than the 390-4V piece.Ford part number C7OZ-9741-B.Also good for 1968-1/2 - 428CJ.

Weld in bracket for attaching the trunk lock striker on any 1967-68 Mercury Cougar. Majority of these have rust forming at the base where it meets the trunk floor. Removed from a rust free western Cougar. Ford part number C7WY-6543235-A.

Weld in bracket for attaching the trunk lock striker on any 1969-70 Mercury Cougar. Majority of these have rust forming at the base where it meets the trunk floor. Removed from a rust free western Cougar. Ford part number C9WY-6543235-A.

This used upper column bracket bolts to the brake pedestal bracket under your dash. The two threaded studs face downward and are used to attach the lower column bracket.

Used tilt column vacuum can bracket for the 1968 Mercury Cougar *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

One year only design.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used bracket for the vacuum reservoir for the tilt / tilt away steering column found in the Mercury cougar or Ford Mustang. This specialized little bracket is used to mount the tilt / tilt away vacuum reservoir in place. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement...

Used bracket for the vacuum reservoir for the tilt / tilt away steering column found in the Mercury cougar or Ford Mustang. This specialized little bracket is used to mount the tilt / tilt away vacuum reservoir in place. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement...

Used to mount the vacuum storage tank inside the driver fender, two required per car, sold individually. Exact same part as what is found on the 1968 Cougar just a slightly different clips is used for 1969. Cougar part number C8WY-13B008-A.

22954 Door vent window pivot bracket, mounts to the bottom of the vent window assembly on a 1967-68 Mercury Cougar or Ford Mustang. Right and left side brackets interchange.

Used windshield wiper mounting bracket for any 1967-68 Mercury Cougar or Ford Mustang. Part of the wiper motor assembly in the Master Parts Catalog, so no Ford number found.

Power steering hose bracket for early model Mustangs.

Used original lower power steering hose mounting bracket for 289 / 302 / 351 1967-69. Comes as shown with rubber insulator. This used version has the indexing tab which the reproduction does not. May come with new bolt and or rubber insulator.Replaces Ford part # C7DZ-3A609-A, C7DZ-3A610-A, C7ZZ-3C510-B, and C8ZZ-3C510-A.

Used mounting tab or bracket, that is embedded into the dash pad below the instrument cluster for attaching the lower dash filler. These can be glued back into the foam with adhesive. Right and left side pieces are different, this one attaches to the lower left side. The companion bracket is also available.

Used mounting tab or bracket, that is embedded into the dash pad below the instrument cluster for attaching the lower dash filler. These can be glued back into the foam with adhesive. Right and left side pieces are different, this one attaches to the lower right side. The companion bracket is also available.

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Ford part number C7ZZ-17B862-A, fits all 1967-68 Mercury Cougar and Ford Mustang.Sold as a pair and are not side specific. 

These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Fits all 1969-70 Mercury Cougar and Ford Mustang. Sold as a pair and are not side specific. 

Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford mustangs equipped with disc brakes.

Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford Mustangs equipped with drum brakes.

Fuel and brake line fastener kit. Fits all 1967 Mercury Cougar and Ford Mustang with V-8 engines and 2 piece fuel line from tank to pump. Early production 1967 cars used a 1 piece fuel line from the gas tank to fuel pump. Eventually Ford installed 2 piece fuel lines during 1967. This is only for the two piece fuel line.*Note these are for the original and reproduction style fuel lines that were 5/16 thick, which was unique to 1967 production.

Rear Wheel Cylinder (7/8", Left Rear). For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller.The difference in this premium version and the economy version, is that this cylinder will be concours correct and have the smaller 1/4" fitting. Replaces Ford Part #: C20Z-2261-B, C3AZ-2261-B, C4TZ-2261-A, C60Z-2261-A, D3TZ-2261-A, D3ZZ-2261-A. ...

Rear Wheel Cylinder (7/8", Left Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller. You can find the premium concours correct version here.

Rear Wheel Cylinder (7/8", Right Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller.You can find the premium concors correct version here. Replaces Ford Part #: C20Z-2262-B, C3AZ-2262-B, C4TZ-2262-A, C60Z-2262-A, D2ZZ-2262-A, D3TZ-2262-A, D3ZZ-2262-A. ...

Rear Wheel Cylinder (7/8", Right Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller. The difference in this premium version and the economy version, is that this cylinder will be concours correct and have the smaller 1/4" fitting.Replaces Ford Part #: C20Z-2262-B, C3AZ-2262-B, C4TZ-2262-A, C60Z-2262-A, D2ZZ-2262-A, D3TZ-2262-A, D3ZZ-2262-A. ...

Rear Drum Brake Wheel Cylinder for 390, 427, 428 w/ Front Disk Brakes (13/16", Right Hand & Left Hand same) You can find the premium concours correct version here. Replaces Ford Part #: C7ZZ-2262-A

Rear Drum Brake Wheel Cylinder for 390, 427, 428 w/ Front Disk Brakes (13/16", Right Hand & Left Hand same) The difference in this premium version and the economy version, is that this cylinder will be concours correct and have the smaller 1/4" fitting. Replaces Ford Part #: C7ZZ-2262-A

Rear Wheel Cylinder (29/32", Right Hand) Fits either Right Hand or Left Hand. Sold individually, 2 required per car. Replaces Ford Part #: C3OZ-2262-B and D2ZZ-2262-B.

Reproduction driver side (left hand) front wheel cylinder for 10 inch x 2-1/2 inch drum brakes. This unit fits into a 1-3/32 inch hole on the brake backing plate. Replaces Ford Part # C6OZ-2062-B or C9TZ-2062-B.

Reproduction driver side (left hand) front wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits in a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part #: C3OZ-2062-B, D2ZZ-2062-A, & D3ZZ-2062-A.

Rear Wheel Cylinders for 4 Wheel Drum Brakes (15/16", LH). Replaces Ford Part #: C7AZ-2262-C.