General (Old Category Structure)

This pair of sturdy cardboard taillight covers / protectors are designed to protect your taillight sockets from being dislodged or damaged. In addition to the protection they offer they also serve to give a "cleaner" look to your luggage compartment. Will require minor trimming. Please let us know if you have a good used example so as to use as a template to perfect these parts.

Used grade "A" taillight wiring harness for the Mercury Cougar. No cuts or splices, perfect plugs with no visible corrosion.  This harness is for the Late 1971 (after 5/15/1971) through 1972.  There were 2 other harnesses for early 1971 (D1WY-14405-B before 2/1/71 and D1WY-14405-D from 2/1/71 - 5/15/71).  If you are in need of one of these early harnesses, please contact us so we can discuss what you need.Ford part # D2WY-14405-A.*NOTE* Need help diagnosing a Cougar...

This is a restored 1973 driver side taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. ...

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.

This is a restored 1973 passenger side taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. ...

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.

Reproduction taillight panel for the 67-68 Cougar. Yet another in a long line of great fitting parts from our friends over at Dynacorn, this replacement taillight panel is perfect for those of you who have rust holes in and around the taillight area. As seen in the photo above, this is only the taillight panel and will not include the quarter extension panels or the rear taillight lower structure. ...

This is how most of our taillight panels are cut off. If you only need a partial panel we can do that too, just give us a ring. Keep in mind we only cut panels like this if both 1/4's are ruined. It is getting very hard to come up with some of these cuts. ...

This is how most of our taillight panels are cut off. If you only need a partial panel we can do that too, just give us a ring. Keep in mind we only cut panels like this if both 1/4's are ruined. It is getting very hard to come up with some of these cuts. Keep in mind that this is an over sized item and cannot get shipped through USPS, it can only go through UPS. You can expect to pay up to $200 in shipping for this item.

This is how most of our taillight panels are cut off. If you only need a partial panel we can do that too, just give us a ring. Keep in mind we only cut panels like this if both 1/4's are ruined. It is getting very hard to come up with some of these cuts.Click on images to enlarge. ...

1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a red 4 pin plug, that is designated D-3 in the wiring diagram. This plug plugs into the sequential turn signal relay in the trunk. We are offering all of the various plugs for repairs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a black 4 pin plug, that is designated D-4 in the wiring diagram. This plug plugs into the sequential turn signal relay in the trunk. We are offering all of the various plugs for repairs.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a white 4 pin plug, that is designated D-4 in the wiring diagram. This plug plugs into the sequential turn signal relay in the trunk. We are offering all of the various plugs for repairs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a black 2 pin plug, that is designated D41 in the wiring diagram. This plug plugs into the sequential turn signal relay in the trunk. We are offering all of the various plugs for repairs.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

1967 and 1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a black 4 pin plug, that is designated J77 in the wiring diagram. This plug plugs into the sequential turn signal motor in the trunk. We are offering all of the various plugs for repairs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s...

67 - 68 Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a black 5 pin plug, that is designated P79 in the wiring diagram. This plug plugs into the emergency warning relay flasher in the trunk. We are offering all of the various plugs for repairs.Good for both STD and XR7 models*NOTE* Need help diagnosing a Cougar turn signal problem? Victor...

1967 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a black 4 pin plug, that is designated P83 in the wiring diagram. This plug plugs into the stop lamp relay in the trunk. We are offering all of the various plugs for repairs.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable...

Sold as a pair, these cardboard protectors do more than just give your trunk a clean look, they protect your tail light sockets from damage. If you see them advertised for less we want to know about it!

This oddball sequential unit was only used from 2/1/1971 to 5/15/1971 and will be of no interest except for to select few. The differentiating factor is the hard plastic connectors. We can supply a reproduction of this unit but it requires that you send your old unit to to us so we can reuse the plugs. Ford part # D1WY-13A366-C.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

Driver side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the center position of your taillight section.

Driver side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the inner position of your taillight section.

Driver side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the outer position of your taillight section.

Passenger side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the center position of your taillight section.

Passenger side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the inner position of your taillight section.

Passenger side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the outer position of your taillight section.

Used Standard Grade A Taillight Wiring Harness for the 1973 Mercury Cougar 

This grade "B" taillight harness is a good used harness that may have one or two professional repairs. Not for use with XR7 or Eliminator models. The difference between XR7 and standard is that the XR7 has a two wire plug to the sending unit and the standard has a single wire.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Used grade "B" taillight wiring harness for the Mercury Cougar. This harness may have one or two professional repairs.This harness is for the Late 1971 (after 5/15/1971) through 1972.  There were 2 other harnesses for early 1971 (D1WY-14405-B before 2/1/71 and D1WY-14405-D from 2/1/71 - 5/15/71).  If you are in need of one of these early harnesses, please contact us so we can discuss what you need.Ford part # D2WY-14405-A.*NOTE* Need help diagnosing a Cougar turn signal...

Used Standard Grade B Taillight Wiring Harness for the 1973 Mercury Cougar 

1968 XR7 and standard Cougars use the same rear wiring harness to the taillights. This is a grade "B" grade harness that may be spliced or repaired. XR7 and Standard Cougars use the same rear wiring harness to the taillights, only the sub-harness that connects to it that runs along the underside of the package tray and down to the fuel sending unit differs XR7 vs. Standard. The major difference is that the xr7 utilizes a two wire plug and the Standard Cougar uses a single wire. Harness begins...

Correct for Cougars built after 1-2-07 with the stop lamp relay located under dash. XR7 and standard Cougars use the same rear wiring harness to the taillights. This tail light harness is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. The 1157 taillight bulb sockets are sold separately.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's...

1968 differs in the plugs that connect to the sequential unit. Correct for Cougars built after 1-2-67 with the stop lamp relay located under dash. XR7 and standard Cougars use the same rear wiring harness to the tail lights This is a grade "B" harness that may have minor sun damage, splices or other cosmetic defects. The 1157 taillight bulb sockets are sold separately.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the...

Grade "A" used harness with no cuts or splices. Correct for XR7, Eliminator, and 1969-70 Shelby Mustang GT-350 and GT-500. Ford part # C9WY-14405-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Used grade "A" taillight wiring harness for the Mercury Cougar. No cuts or splices, perfect plugs with no visible corrosion.  This harness is for the Late 1971 (after 5/15/1971) through 1972.  There were 2 other harnesses for early 1971 (D1WY-14405-A before 2/1/71 and D1WY-14405-C from 2/1/71 - 5/15/71).  If you are in need of one of these early harnesses, please contact us so we can discuss what you need.Ford Part Number: D2WY-14405-B. *NOTE* Need help diagnosing a Cougar...

Used XR7 Taillight Wiring Harness for the 1973 Mercury Cougar 

Used grade "B" taillight wiring harness for the Mercury Cougar. This unit may have one or two professional repairs.This harness is for the EARLY 1971 (before 5/15/1971). There were 2 harnesses for early 1971 (D1WY-14405-A before 2/1/71 and D1WY-14405-C from 2/1/71 - 5/15/71).  Ford Part Number: D2WY-14405-B. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

Used grade "B" taillight wiring harness for the Mercury Cougar. This unit may have one or two professional repairs.This harness is for the Late 1971 (after 5/15/1971) through 1972.  There were 2 other harnesses for early 1971 (D1WY-14405-A before 2/1/71 and D1WY-14405-C from 2/1/71 - 5/15/71).  Ford Part Number: D2WY-14405-B. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned...

Sold individually, two required per car. This is the same as the 1970 bracket, just different design of clips are used.

This bracket attaches the vacuum storage tank for your headlights to the core support inside the driver fender. It differs from the 1967 bracket in that an oval hole was put in it to allow the socket and pigtail assembly for the side marker light to pass through the bracket located closest to the fender. 1969 uses the exact same bracket except for a slightly different clip design. Sold individually, two required per car. Cougar part number C8WY-13B008-A.

This bracket is used to mount the vacuum storage tank under the driver side fender. Same bracket as was used in 1967 just a slightly different clip. Two required per car, sold individually. Cougar part number D0WY-13B008-A. *Note - The 1967 bracket was used prior to 11/10/1969 built date.

1970 Mercury Cougar hideaway headlight vacuum tank installation brackets (pair) with fasteners. Two different styles of installation brackets for the 1970 vacuum tank found inside the driver side fender. These are tall brackets, the other style utilized 1967 brackets with round spacers.

All parts needed are included to mount your 1970 vacuum storage tank to the core support (backside) under the driver fender. Solid, good original parts found on a Western donor Cougar. Includes short brackets with correct clips, 4 spacers, 4 long bolts with washers, and 4 shorter hex bolts. Typically this kit was used for installing the vacuum tanks until Nov 1969, it is much more convenient to use the more common later kit for the 1970 tank installation.

This 1 1/16" long aluminum spacer was used between the vacuum storage tank and vacuum storage tank brackets. Four required per car, sold individually.

Reproduction Temp Sender Switch with Warning Lights for the 1970, 1971, 1972 and 1973 Ford Mustang with a 351

New temperature sending unit for the 1970 - 1971 Mercury Cougar and Ford Mustang with an actual temperature gauge and a 428, 428CJ (Cobra Jet) or 429CJ (Cobra Jet) engine. Replaces Ford Part #: D0ZZ-10884-A (SW-925)Check out the video below on our new gauge tester: ...

This RAM AIR hood scoop template was created by placing a piece of butcher paper under an original 1969 428 Cobra Jet RAM AIR hood scoop and applying spray paint to the mounting holes and opening. Contrary to what you may have been told, the opening is not supposed to be round, and yes those protrusions you see are in fact correct. The 1969 uses a slightly different cut out than the 1970.

This RAM AIR hood scoop template was created by placing a piece of butcher paper under an original 1970 428 Cobra Jet RAM AIR hood scoop and applying spray paint to the mounting holes and opening. Contrary to what you may have been told, the opening is not supposed to be round, and yes those protrusions you see are in fact correct. The 1970 uses a slightly different cut out than the 1969. If you can make a template for us from your 1968 or 1969 Ram Air Cougar we would love to hear from you! ...

For those wanting to make their own "custom" package tray this will assist you in getting the correct dimensions the first time. This template is traced from a reproduction packege tray onto a piece of butcher paper.