Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar.
Body assembly manual used by the workers when they were originally building the Cougar and Mustang. Must have if you are putting together your Cougar or Mustang, and a great resource when tearing it down!
Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"
Reproduction master exterior fastener kit for the Mercury Cougar Standard and XR7. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Fender Splash Shields (front of fender) Fender Splash Shields (rear of fender) Battery Tray Hood and Hinges Cowl Panel Shock Tower Braces Hood Levelers Hood Latch and Catch Fender Extensions Quarter Panel Extensions Trunk Latch...
Metal reinforcing plate welded to the center of the rear body, where the third member may come into contact with the floor. Cut from one of our many parts cars. Likely originally had a Ford part number of 4731. Removed from a 1967-68 Mercury Cougar, we suspect that it will not be a direct fit for a Mustang. 9 inch rear ends would be as shown. 8 inch rear ends would have a rubber axle snubber bumper attached. See related items.This part will come as shown, spot welds will need to be drilled and...
Metal reinforcing plate welded to the center of the rear body, where the 9 inch third member may come into contact with the floor. Cut from one of our many parts cars. Likely originally had a Ford part number of 4731. Removed from a 1969-70 Mercury Cougar, we suspect that it will not be a direct fit for a Mustang. This part will come as shown, spot welds will need to be drilled and the plate welded to your chassis.
Metal reinforcing plate welded to the center of the rear body, where the 9 inch third member may come into contact with the floor. Cut from one of our many parts cars. Likely originally had a Ford part number of 4731. Removed from a 1971-73 Mercury Cougar, we suspect that it will not be a direct fit for a Mustang.This part will come as shown, spot welds will need to be drilled and the plate welded to your chassis.
New rubber body plug, fits 1-3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Typical application is rear leaf spring access.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377356.
New rubber body plug, fits 1-1/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some of the holes include: inner frame rails at radiator, center of firewall, and side of cowl.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377936.
New rubber body plug, fits 3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: frame rails at sway bar, rear floor pan, LH fender apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377977.
New rubber body plug, fits 9/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles, typically they are for: front fender aprons, transmission cross member, and radiator support. Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 376966.
New rubber body plug, fits oval rear shock access hole. 1-3/4" x 3-3/8" oval holes. Sold individually, Usually 1 per car. Fits 1971-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 384440.
Sold individually.
Reproduction rubber body plug for the Mercury Cougar and Ford Mustang. This 11/16" x 15/16" oval unit fits to the top of the cowl underneath the front fenders. These little units are sold individually, and their are usually two required per car. Replaces Ford plug marked 383181-S.
New rubber body plug, fits 13/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: trunk floor pan, side of cowl at door, and LH apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377949.
New rubber body plug, oval , fits inner frame rails. 3/4" x 1" oval holes. Sold individually, Usually 2 per car. Fits 1967-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378770-S.
44 Piece kit that includes quarter panel drain plugs.
C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1969-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Some time between 1969 and 1973 this plate underwent a revision by Ford. We are going to split by generation. 1969-70 plates are flat on one edge. 1971-73 has a slight hump or bend. Either works and...
These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...
Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973...
This dense, closed cell foam adheres to the back of your 1967 seat frame. This is a used part, carefully (but not always perfectly) removed from an original frame. No water or pest damage, bucket and bench seat are the same as well as right and left.Sold individually.
Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.
Reproduction 289 - 302 Alternator Bolt w- Smog for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold individually
Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!
Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!
Used intake manifold bolt for the Mercury Cougar or Ford Mustang equipped with the 351C engine. This item is sold individually.Ford part # 56145-S.
Replaces Ford Part # C9OZ-6065-B
Sold individually. Replaces Ford Part # C9OZ-6065-A
Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.
Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.
Bolt for attaching the emergency brake Pedal Assembly. This is a 5/16-18 washer head bolt. Sold individually, Three bolts attach the E-brake assembly. Fits all 1969-70 Mercury Cougar and Ford Mustang.
Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
Sold individually Zinc (dark silver)
Bolts and installation kit for most 1970-73 Mercury Cougar and Ford anything, including Mustang with V-8 engines. Kit includes main pivot bolt and adjusting bolt as shown. Spacer not included, but available used.
Replaces Ford Part # 43260-S Sold individually
New screw with a correct 3/8 inch hex head for installing all armrests for all years.
384356-S Bolt with captured washer. Mounts the two stops and is used to install the channel assembly. Five total bolts per door glass, 10 used per car. Very specific sized captured washer for distributing pressure on the glass. Click on images to enlarge. 1970 similar. ...
3/8-16 X 4.0 GR-8 9/16 AF Zinc Dichromate Replaces Ford Part #: 370584-S
part # 382101-S2 Sold individually
part# 372434-SSold Individually.Head size: 5/8"Thread size: 7/16"
Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.
12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Sold indiviually Phosphate & Oil (gay-black)
part # C1AE-6065-A. Longer of two. Sold individually
part # C1AE-6065-C. Shorter of two. Sold individually
Distributor hold down bolt. All V-8 engines.1967-73 Mercury Cougar and Ford Mustang. 5/16 x 7/8" bolt, 1/2' hex head.