Body

Reproduction "A" pillar repair panels for your 67 - 68 Cougar or Mustang. Included in this kit are the two pillar patches and four backing plates for the door hinges.

Reproduction "A" pillar repair panels for your 69 - 70 Cougar or Mustang. Included in this kit are the two pillar patches and four backing plates for the door hinges.

Reproduction driver side inner A pillar inner / kick panel for the 67 - 68 Cougar or Mustang.

Reproduction driver side inner A pillar / kick panel for the 1971 - 1973 Cougar or Mustang.

Reproduction inner "A" pillar panel and fresh air vent vent panel set for the driver side (left hand) of the Mercury Cougar or Ford Mustang. This item features weld through primer and is ready to install. Unfortunately both Cougars and Mustangs alike are prone to rust in these areas, so finding a nice original piece can be difficult. We're delighted to have this high quality panel set to offer you the perfect pieces to replace those rusty units you have now!

Reproduction inner "A" pillar and fresh air vent panel set for the passenger side (right hand) of the Mercury Cougar or Ford Mustang. This item features weld through primer and is ready to install. Unfortunately both Cougars and Mustangs alike are prone to rust in these areas, so finding a nice original piece can be difficult. We're delighted to have this high quality panel set to offer you the perfect pieces to replace those rusty units you have now!

Reproduction passenger side inner A pillar inner / kick panel for the 67 - 68 Cougar or Mustang.

Reproduction passenger side inner A pillar / kick panel for the 1971 - 1973 Cougar or Mustang.

Reproduction pair of A/C vent registers for your 69 - 70 Cougar or Mustang. Sold as a pair. Replaces Ford part numbers: C9ZZ-19893-D driver side, C9ZZ-19893-C passenger side.

Ford called this small door latch part an adjuster. It threads onto the bottom of the door latch rod inside the door. Common to most Ford products 1965-1970. Ford part number C5AZ-62218106-A.

Threaded anchor that slides into the trunk hinge on each side. Sold individually, two needed per car. These are for Cougar and Mustang built after approximately 3/31/1971. Look for bolt spacing of 4-1/4 inches on those trunk lids.  Ford number C9AZ-6242752-A.*Note - Trunks prior to March 31, 1971, did not use this anchor plate. I think that they had a bolt spacing of 4-1/2 inches.

These keep the trunk hinge spring rods from rattling. These are a reproduction of the anti-rattler for 67-68 Cougar / 65-68 Mustang.   Replaces Ford part # C5ZZ-6545028. These also work for the 69-70 Cougar / Mustang better than what came factory, which, according to the Ford MPC, for 69-70 would have actually been 1/8" x 7/8" Vinyl Foam Weatherstrip Tape, Ford part C6AZ-19627-A. Check out our trunk torsion bar installation video: ...

Reproduction driver side (left hand) rear apron extension for 1967 - 1968 Mercury Cougar and Ford Mustang. These plates almost always get destroyed when installing new aprons, so don't forget to grab one for each side you work on.

Reproduction passenger side (right hand) rear apron extension for the 1967 - 1968 Mercury Cougar and Ford Mustang. These plates almost always get destroyed when installing new aprons, so don't forget to grab one for each side you work on.

Improved reproduction pair of sun roof cables for the Mercury Cougar but they will interchange with most all early Golde / American Sunroof Corporation Moonroof / Sunroofs. Keep in mind this same basic cable design was used on many makes including Thunderbird, Lincoln, Mopar, BMW, Mercedes, Porsche and several other cars. (minor revisions were made through the years). These cables measure 64 1/2" tip to tip which may be too long for some applications. All examples we have found for the Cougar...

Good used solid panel with all parts removed. Panel measures 19.5" x 37". Whereas at first glance these may all look the same, the contour of the roof changes with the body style changes. Call us for price and availability on panels with varying degrees of repairable rust.

Protects quarter panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part #: C4SZ-6323370-A.

These barrel nuts or clips are exactly like the original ones inserted into the trunk for attaching 1967-68 "Mercury" script, and 1971-72 Mercury Cougar "Mercury" Hood scripts. The manufacturer indicates that these tubular nuts fit 1/8" holes. Pin size on those emblems are 3/32".These clips are also used to attach the 1967 quarter panel emblems.

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

NOTE: At the moment the supplier is only making the late model version of this beltline kit. The late version has a slight bend in the chromed quarter piece, whereas the early version is straight (see photo above). Made With Exact Materials As Original. Eight piece kit that includes inner and outer belt-line, enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them...

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

A nice reproduction of the inner door remote mirror bezel. This is concours quality and an exact fit and finish. Just like the originals, these are made from chromed plastic. Comes with correct mounting hardware. Replaces Ford Part # : C8SZ-17B733-B

Metal reinforcing plate welded to the center of the rear body, where the third member may come into contact with the floor. Cut from one of our many parts cars. Likely originally had a Ford part number of 4731. Removed from a 1967-68 Mercury Cougar, we suspect that it will not be a direct fit for a Mustang. 9 inch rear ends would be as shown. 8 inch rear ends would have a rubber axle snubber bumper attached. See related items.This part will come as shown, spot welds will need to be drilled and...

Metal reinforcing plate welded to the center of the rear body, where the 9 inch third member may come into contact with the floor. Cut from one of our many parts cars. Likely originally had a Ford part number of 4731. Removed from a 1969-70 Mercury Cougar, we suspect that it will not be a direct fit for a Mustang. This part will come as shown, spot welds will need to be drilled and the plate welded to your chassis.

Metal reinforcing plate welded to the center of the rear body, where the 9 inch third member may come into contact with the floor. Cut from one of our many parts cars. Likely originally had a Ford part number of 4731. Removed from a 1971-73 Mercury Cougar, we suspect that it will not be a direct fit for a Mustang.This part will come as shown, spot welds will need to be drilled and the plate welded to your chassis.

   Sold individually.

These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...

Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973...

57084-S Attaching bolt with 7/16" hex head and captured washer. Among other things, it is used to attach the door run, window stops (all 3), both window stabilizers, and the window regulator. Same bolts for manual and power window regulators. Bolt sold individually, there are a good handful in each door. This bolt is used for bolting in the bolt-in glass on 1970, lower "L" bracket for rear quarter windows on 1971-73 Cougar and Mustangs.

Bolt with toothed washer for attaching 1967-68 Mercury Cougar and Ford Mustang door window parts. Both of the door window rear stops, and rear door guide. 1/4-20 bolt threads.

Not a concours correct head pattern, but it looks good. Bright cadmium finish. 5/16-18 x 7/8 long.

Ford part # for the nut is 33772-S4, for the bolt 370301-S8, and the flat washer 358994-S.

7/16-14 x 1-1/4" style bolt and nut for installing the shock tower brace to the cowl. One bolt and nut.Ford part # for the nut is 375918-S7-8, bolt 370301-S8.

Used 1971-73 style bolt and nut for installing the shock tower brace to the cowl.

These reproduction fender to pillar bracket bolts fit both the Standard and XR7.

Reproduction pair of 1 1/8" long hood latch support bolts for the 1968 Mercury Cougar. Looking through cars with original parts, we've found a few different variations of the types of bolts used. It would be best to measure what you have and purchase the correct length bolts.

These reproduction hood latch catch bolts fit both the Standard and XR7.

Reproduction pair of 7/8" long hood latch support bolts for the 1968 Mercury Cougar. Looking through cars with original parts, we've found a few different variations of the types of bolts used. It would be best to measure what you have and purchase the correct length bolts.

Reproduction bolts for the deck/trunk lid latch for the Mercury Cougar or Ford Mustang. This is a set of five bolts and will fit both the standard and XR7. Total of 5 bolts used 1969-73, 1967-68 Cougars will only use 2. We think that Mustangs use 5 on all years 1967-73.AMK F-227 ...

Reproduction bolts and U nuts for mounting the front valances on either a Mercury Cougar or Ford Mustang.

Here are our reproduction hood latch support brace bolts and U nuts for the Mercury Cougar.

Rear most convertible top bow #4, from a 1969-70 Mercury Cougar or Ford Mustang convertible top assembly. This is the last bow and would have had a tack strip attached. Bow only, slat brackets sold separately. Ford part number C9ZZ-7651278-A.

Used to cushion and protect top vinyl from excessive wear from side rails. Unfortunately none of the reproductions that we have found resemble the OEM pads. OEM pads looked canvas on the under side that goes against the convertible top rails, and what looked like the soft side of a velcro strip on the upper side that makes contact with the convertible top itself. These are still highly recommended as they keep the convertible top rails from rubbing thorough the convertible top. "I found WCCC...

Good used Western part that is not bent or heavily rusted and the left is the same as right. This is the round style and the round and the flat 1971-72 fender braces fully interchange.Ford master part # D3WY-16B134-A.