Body

Our Grade "B" 1967 - 1968 front fender extensions almost always have the damage centered around the "tip" as evidenced by the one you see pictured. We will not send you junk, but rather a part needing only minor attention. Notice the portion behind the eyebrow is painted black from the factory. Used hardware is often available for free if you mention it. Do not over tighten this part as they are soft metal and warp easily. Ford casting number as seen on back reads C7WB-16019-A. Do you have...

Our grade "B" fender extensions have a few dings, scrapes or warping due to over tightening of studs. Ford part # C9WB-16A169-B, Mercury MPC # C9WY-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help.

Our grade  B fender extensions have dings, scrapes or warping due to over tightening of studs. Ford part # D0WB-16019. Mercury MPC # D0WY-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help.

Our Grade "B" fender extensions almost always have the damage centered around the "tip" as evidenced by the one you see pictured. We will not send you junk, but rather a part needing only minor attention. Ford part # C7WB-16018-A.

Our grade B fender extensions will have dings, scrapes or warping due to over tightening of studs. Ford part # D0WB-16018. Mercury MPC # D0WY-16018-A. Do you have questions about your Cat's factory pinstriping? This link may help.

New Old Stock passenger side fender extension for the 67 - 68 Cougar.  Ford casting number as seen from the back side reads C7WB-16019-A.

New old stock 1969 Mercury Cougar Passenger Side Front Fender Extension Ford part # C9WB-16A168-B, Mercury MPC # C9WY-16018-A. Do you have questions about your Cat's factory pinstriping? This link may help.

This is our reproduction fender fastener kit for you r Mercury Cougar or Ford Mustang.

Reproduction Driver side fender extension. This latest in a series of 68 reproduction sheet metal parts is just what the market has been waiting for! The dimensions are EXACT down to the 1/16". NOTE - This splash shield does not come with the rubber, but you can find the seal kit here. Replaces Ford part # C7WB-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help. ...

This unit consists of a metal shield with rubber stapled to the edges mimicking the fender contours. In most cases, these used shields will need to have the stapled rubber shields replaced. A Mustang shield will not fit a Cougar because the fender has a much different contour.Ford part # C7WY-16A574-A.

This unit consists of a metal shield with rubber stapled to the edges mimicking the fender contours. In most cases, these used shields will need to have the stapled rubber shields replaced. Same part as the1967 piece, but with a section cut out for the marker light housing. A Mustang shield will not fit a Cougar Because the fender has a much different contour.Ford part # C8WY-16A574-A.

Mercury Cougar front inner fender splash shield featuring all plastic construction. Ford part # C9WB-16A563-A, MPC number C9WY-16A574-A.

Mercury Cougar front inner fender splash shield featuring all plastic construction.Ford part # D0WB-16A563-A, MPC number D0WY-16103-A.

Mercury Cougar left front fender inner splash shield.Ford part # D1WY-16103-A.

Mercury Cougar rear inner splash shield featuring all plastic construction.Ford part # C9WB-16B569-E, MPC # C9WY-16103-A.

Mercury Cougar left rear fender inner splash shield.Ford part # D1WY-16103-B.

Reproduction Passenger side fender extension. This latest in a series of 68 reproduction sheet metal parts is just what the market has been waiting for! The dimensions are EXACT down to the 1/16". NOTE - This splash shield does not come with the rubber, but you can find the seal kit here. Replaces Ford part number C7WB-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help. ...

This unit consists of a metal shield with rubber stapled to the edges mimicking the fender contours. In most cases,  these used shields will need to have the stapled rubber shields replaced. The 1967 and 1968 Mercury Cougar inner fender splash shields were constructed using a metal panel with a rubber material stapled to this metal shield. A Mustang shield will not fit a Cougar because the fender has a much different contour.Ford part # C7WY-16A573-A.*Installation and detailing tip -...

This unit consists of a metal shield with rubber stapled to the edges mimicking the fender contours. In most cases, these used shields will need the to have stapled rubber shields replaced. Same part as the 1967 piece, but with a section cut out for the marker light housing. A Mustang shield will not fit a Cougar because the fender has a much different contour. Supply limited due to the proximity to the battery.Ford part # C8WY-16A573-A.

Mercury Cougar front inner fender splash shield featuring all plastic construction. Ford part # C9WB-16A562-A, MPC number C9WY-16A573-A.

Mercury Cougar front inner fender splash shield featuring all plastic construction. Ford part # D0WB-16A562-A, MPC number D0WY-1602-A.

Mercury Cougar right front fender inner splash shield.Ford part # D1WY-16102-A.

Mercury Cougar rear inner splash shield featuring all plastic construction.Ford part # C9WB-16B568-E, MPC number C9WY-16102-A.

Mercury Cougar right rear fender inner splash shield.Ford part # D1WY-16102-B.

These are our reproduction fender splash shield screws for your Mercury Cougar or Ford Mustang.

These reproduction fender splash shield bracket screws and J nuts fit both the Standard and XR7.

Here are our reproduction fender to pillar bolts for your Mercury Cougar or Ford Mustang.

Lightweight fenders that were bought for $800 and never used. Very lightweight, perfect for a Race car.Sold as a pair. Keep in mind that even though these are lightweight fenders, shipping charges will be high because of oversized packaging.

These dense, cardboard fillers are placed over the trunk drop offs. They are sturdy reproductions that fit well and every old Cougar seems to need them as moisture and general wear and tear take their toll over the decades. Sold as a pair only. If you see these advertised for less money elsewhere we would like to be notified.

These die cut sturdy trunk filler boards fit over either side of the trunk drop off and allow your trunk mat to lay flat over the trunk drop off areas. Sold as a pair.

Sold as a pair. Not only are these usually in poor shape but more times than not they are missing altogether. Great price on a quality, die cut part.

Finally, a reproduction firewall for your Mercury Cougar or Ford Mustang convertible. Ford part # D1ZZ-6501610-A.

Reproduction Mercury Cougar and Ford Mustang firewall.Here's our little film to help you fortify your flexxy feline!

Reproduction stamped steel firewall for Mercury Cougar and Ford Mustang.Here's our video on front suspension and chassis upgrades.

Pair of reproduction firewall to shock tower braces for the Mercury Cougar or Ford Mustang. These Chinese made units are already painted black, so the only thing you need to do is bolt them on. However, we highly recommend that you get our superior quality used FoMoCo units right here!Replaces Ford part #'s C9ZZ-16A053-A driver side (left hand), C9ZZ-16A052-A passenger side (right hand). ...

This is a great, well fitting reproduction and is also all you need to replace the firewall on your 71 - 73 Cougar or Mustang. This is the entire wall, from passenger side to driver side, cowl to floor pan. Made specific for cars with A/C.

Rubber coupler for connecting the drive motor and the geardrive for operating the ASC factory sunroofs. American Sunroof Corporation started using this shorter connector sometime in late 1968 on the very early 1969 cars. ASC power sunroofs (technically moonroofs since they had solid covers instead of glass) were offered on many new cars such as Mercury Cougar, Lincoln Mark series, Ford Thunderbird, and many Mopars or Dodge, Chrysler, and Plymouth cars.

Reproduction floor pan firewall extension for the driver side (left hand) of your 67 - 68 Cougar.

Reproduction passenger side (right hand) floor pan to firewall extension for the 67-68 Cougar.

These correct floor pan patches are for the 1969-70 convertible and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long and 15 1/4" wide. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

This piece runs under the floor over the transmission where the floor pan meets the firewall.

Reproduction driver side (left hand) floor pan to cowl side panel for Mercury Cougar and Ford Mustang. Normal 0 false false false EN-US X-NONE X-NONE Here's our little film to help you fortify your car! ...

Reproduction driver side (left hand) inner front frame patch for Mercury Cougar and Ford Mustang.

Reproduction passenger side (right hand) inner front frame patch for Mercury Cougar and Ford Mustang.

Reproduction pair of frame rail / floor supports. These extend off the back of the front frame rail and give support under the front floor pan. Includes driver and passenger sides.

Reproduction pair of frame rail / floor supports. These extend off the back of the front frame rail and give support under the front floor pan.Includes driver and passenger sides.

Reproduction driver side (left hand) inner front frame patch for Mercury Cougar and Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below:

Reproduction passenger side (right hand) inner front frame patch for the Mercury Cougar or Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below: