Body

Here are our reproduction fender splash shield screws that fit 1967 Standard and XR7.

Here are our reproduction fender splash shield screws for your Mercury Cougar or Ford Mustang.

This reproduction hood latch support screw kit fits both the Standard and XR7 and is sold as a set of 4.

8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

These vinyl coated clips hold the weatherstrip and guide the window when rolling up. Used clips usually are rusted and the vinyl portion is peeling. Sold individually and four are required per car. Replaces Ford part #: C9ZZ-6522204. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Contoured stainless steel trim for the passenger side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A14-A Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Sold separately, please choose between driver or passenger side. Used (poor condition) weather strip may or may not be in place....

Seals between chrome vent frames and door on exterior side. Stops water from leaking between vent window and door. Keep in mind that this seal comes as one strip and it meant to be cut down the middle. Sold as a pair. Replaces Ford part #: C6OZ-6322280 or C6OZ-63222A80-A.

These high quality vent window seals are the first on the market to replace the original Ford part exactly. This is the small seal at the front of the door and next to the door weatherstrip. Sold as a pair. Replaces Ford Part #: C7ZZ-6522332/3, C7ZZ-65223A32-B, C7ZZ-65223A33-B, C7ZZ-65223A32-C & C7ZZ-65223A33-C.

These are good reproductions of the originals for your American Sunroof Corporation Golde Sun Roof. The roof opening seal is 89 1/4" x 3/4" and the seal that affixes to the rear edge of the roof panel measures 42 1/2" x 3/4". These have the correct aluminum inner core with rubber bead, wrapped in the correct felt textured, black material. They're are made by the original manufacturer in Germany and will fit all Cougars equipped with the ASC sunroof. Very hard to find seals at a reasonable...

Reproduction door glass seals for the front of the door to the window glass for the Mercury Cougar or Ford Mustang. Replaces Ford part # C9ZZ-6520264. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Premium reproduction rubber seal with the proper thickness of the 1967-68 seal as found on Mercury Cougar and Ford Mustang except these are not molded to the extension contours. Starting in 1969 this channel seal was manufactured slightly smaller which tightened up the gap on the fender and quarter extension seals. This seal maintains the slightly larger gaps. Sold as a pair, two pairs needed per car.  Each package has 2 strips of 25 1/2" lengths. *NOTE* Do not over tighten the...

Used convertible rear seat structure cut from a 69 - 70 Cougar Convertible parts car. This will not fit a Mustang due to the differences in the wheel houses and transition panel. Keep in mind that this is an oversized item and cannot ship through any conventional means. Truck freight and crating fees will apply. 

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 4 total per car, all 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped for the front seat belts inboard on 1971-73 cars. Round anchor bracket with factory welded nut for added strength. See related items for good used seat belt anchor plates if you have concours needs. Replaces Ford Part # D1AZ-6561216-A. ...

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

This seat riser / platform is specific to Mustang, but if you're "vertically challenged"....you may want to go ahead and use this part on your Cougar. It'll raise your seat up enough so that you don't have to use phone books anymore!

This seat riser / platform is specific to Mustang, but if you're "vertically challenged"....you may want to go ahead and use this part on your Cougar. It'll raise your seat up enough so that you don't have to use phone books anymore!

Here is our free download for the 1968 Mercury Cougar sunroof panel service procedures.

Published by the Lincoln Mercury Division to provide information on diagnosis, service procedures, adjustments & specs. Filled with diagrams and illustrations to help disassemble, repair & reassemble various components pertaining to the sunroof panel on the 1968 Mercury Cougar.Issue # LM-7882April 1968

Reproduction shock support for the 67 - 68 Cougar. This support sits underneath the transition hump and attaches the upper mounts of each rear shock. The shock hardware is accessible through two access holes on the hump.

Used upper shock mount cross member for Q code 351CJ and 351C-4V Cougars from 1972-73. We think. Probably includes 4 speed cars too from 1971. Bracket appears to be slightly different than the Mustang version of the same generation. Pretty rare bracket, likely needed the competition handling package option, with the 351C-4V engines. Basic Ford part number is 18A000. This is the rear upper shock cross member, designed for staggered rear shocks. Notice the missing hole for the passenger...

If you buy this reproduction tower, you will no doubt save you time in clean up. But nothing will ever fit and look like original FoMoCo towers!Here's a little film to help you fortify your flexxy feline!

This tower is technically incorrect for a 1969-70 Mercury Cougar as it has no reinforcement plate. Cougar owners would definitely want to buy a good used tower instead of this reproduction. Keep in mind all Cougars came with reinforced towers in 1969-70 just as all 1969-70 Cougars came with the 9" rear-end and 351 or larger engine.Here's a little film to help you fortify your flexxy feline! ...

Excellent condition tower as cut from a Western parts car. No specific part number for this structural front suspension section.Generic Ford part # C7ZZ-16055-D or E, includes apron and side member.Here's a little film to help you fortify your flexxy feline! ...

This is the best upgrade tower for your Cougar or Mustang that does not have the factory reinforcement plate. 1969 features the largest plate of all years 1968-70 and will fit perfectly without modification into any year 1967-70. If both of your towers are cracked this is a no brainer, if only one of your towers are cracked then it would look out of place to have one tower that is reinforced and one that was not. No specific part number for this structural front suspension section. For 1970,...

1970 features a reinforcement plate that is a combination of a 1968 and 1969 plate. This is an excellent upgrade for any 67-70 Cougar or Mustang without reinforced shock towers. This is a 100% clean, uncut tower worthy of any show-car. No specific part number for this structural front suspension section. For 1970, the plate size was shortened, for easier access for spark plug changes. Generic Ford part # D0ZZ-16055-B, included apron and side member. ...

Used driver side (left side) shock tower that is in excellent condition as cut from a Western parts car. For Mercury Cougar and Ford mustang with no specific part number for this structural front suspension section. Generic part # D1ZZ-16055-A, includes apron and side member.

We highly suggest you look at our mint condition used towers for about the same price. Why mess around with repo when you can get FoMoCo?!Here's a little film to help you fortify your flexxy feline!

We highly suggest you look at our mint condition used towers for about the same price. This tower is technically incorrect for a 1969-70 Mercury Cougar as it has no reinforcement plate. Cougar owners would definitely want to buy a good used tower instead of this reproduction. Keep in mind all Cougars came with reinforced towers in 1969-70 just as all 1969-70 Cougars came with the 9" rear-end. All Cougars also came with 351 or larger engines for those years as well, except for the 302...

Excellent condition tower as cut from a Western parts car. If you are replacing two towers because of cracks, we strongly suggest upgrading to a 1969-70 pair of reinforced towers. The 69 and 70 towers are an exact fit into your 1967-68 Ford Mustang or Mercury Cougar. There are no specific part numbers for this structural front suspension section.Generic Ford part #s C7ZZ-16054-C or C7ZZ-16054-E, includes apron and side member. Here's a little film to help you fortify your flexxy feline! ...

This is the best upgrade tower for your Mustang or Cougar that does not have the factory reinforcement plate. 1969 features the largest plate of all years 1968-70 and will fit perfectly without modification into any year 1967-70. If both of your towers are cracked this is a no brainer, if only one of your towers are cracked then it would look out of place to have one tower that is reinforced and one that was not. No specific part number for this structural front suspension section. For...

1970 features a reinforcement plate that is a combination of a 1968 and 1969 plate. This is an excellent upgrade for any 67-70 Cougar or Mustang without reinforced shock towers. This is a 100% clean, uncut tower worthy of any show-car. No specific part number for this structural front suspension section. For 1970, the plate size was shortened, for easier access for spark plug changes. Generic Ford part # D0ZZ-16054-A, included apron and side member. ...

Used passenger side (right hand) shock tower in excellent condition as cut from a Western parts car. No specific part number for this structural front suspension section. Generic Ford part # D1ZZ-16054-A, includes apron and side member.

Reproduction driver side (left hand) shock tower and apron assembly for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Used driver side shock tower and apron assembly for the Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

1971-73 shock towers are not reproduced and finding rust free Western aprons is getting to be a challenge. This is a great value for those needing multiple parts and want factory spot welds. Generic Ford part # D1ZZ-16055-A, includes apron and side member.

Reproduction passenger side shock tower and apron assembly for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) shock tower and apron assembly for Mercury Cougar or Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Used passenger side shock tower and apron assembly for the Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

1971-73 shock towers are not reproduced and finding rust free Western aprons is getting to be a challenge. This is a great value for those needing multiple parts and want factory spot welds. Generic Ford part # D1ZZ-16054-A, includes apron and side member.

Solid, undamaged, used driver side (left hand) shock tower brace for Mercury Cougar and Ford Mustangs. Consider our brace kits for the best bang for your buck! Ford part # C9ZZ-16A053-A. *NOTE* Excludes 1969-70 Boss 429.Here's our little film to help you fortify your flexxy feline!