Your cart is empty!
Buy Details
These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang convertibles...
Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part #C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar...
Complete floor pan for the 1969 - 72 Mercury Cougar or 1965-68* Ford Mustang Convertible. *This is the closest available fit full floor pan for the 1969-73 Ford Mustang Convertible or Mercury Cougar Convertible, this pan will need modification to "make it fit." This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes substantially. ...
THIS ITEM IS OUT OF STOCK UNTIL FURTHER NOTICE Complete floor pan for the 1969-70* Ford Mustang or 1969-70* Mercury Cougar. This item ships direct from the manufacturer for most orders. This item must ship via truck freight. Shipping to business addresses tends to be less than residential addresses, sometimes substantially. This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less...
Complete floor pan for the 1965-68 Ford Mustang. NOTE: Can be made to fit 67-78 Cougar, Included seat risers are Mustang versions, which are taller than the Cougar seat risers. We recommend re-using your original Cougar seat risers, unless you want the extra height of the Mustang risers. Also note that the risers included with this floor pan will not be attached, you'll have to weld them on. Keep in mind Cougar has a longer wheel base which make the portion under the back seat substantially...
Premium grade and quality reproduction floor pan plug. These screw right onto the floor pans prior to the carpet underlay and are much better quality than the originals. The original plugs have rough stampings and are made from galvanized steel. These premium plugs have a smooth cutout and are zinc plated. We also carry the screws. ...
Stamped steel floor pan drain caps used to plug oval holes in the front or rear floors. Economy grade reproduction floor pan plug that closely resembling the originals. Complete with rough stampings made from galvanized steel.
Reproduction passenger side (right hand) floor pan to firewall extension for the 67-68 Cougar.
These correct floor pan patches are for the 1969-70 convertible and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long and 15 1/4" wide. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.
This piece runs under the floor over the transmission where the floor pan meets the firewall.
Reproduction pair of frame rail / floor supports. These extend off the back of the front frame rail and give support under the front floor pan. Includes driver and passenger sides.
Reproduction pair of frame rail / floor supports. These extend off the back of the front frame rail and give support under the front floor pan.Includes driver and passenger sides.
Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.
Looped weld in retainer for the rear seat installation on any 1967-70 Mercury Cougar. This is the front bracket that holds in the rear seat and was used on both coupes and convertibles. We cut out a section of the floor under the rear seat as shown. Make good measurements prior to removal of your old brackets. We think that the Ford number is C5AZ-6263370-B, but we have not been able to verify this for certain. For sure that basic Ford part number is 63370. ...
Hook bracket weld in retainer for the rear seat installation on any 1971-73 Mercury Cougar. This is the front bracket that holds in the rear seat and was used on both coupes and convertibles. Sold individually, two required per car. We cut out a section of the floor under the rear seat as shown. Make good measurements prior to removal of your old brackets. The Ford number is C9AZ-6263370-A.
This is a reproduction long front and rear floor pan. Will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but this will work for all years.
Reproduction full length driver side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years. Hi, and sincerely thanks for all help I've received from WCCC during my (mega) 1968 restoration project. If everyone would be that helpful, the world would be a much better place. ;-) My car is almost ready for the road, but - as always - there...
Reproduction full length passenger side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years.
Used driver side torque box gusset for any 1968-70 Mercury Cougar or Ford Mustang. It is the reinforcement bracket that attaches to the bottom of the torque box and frame rail for extra strength. Sold individually. This part is removed from a parts car, you will need to drill out spot welds and clean up the edges prior to installation. This is for the drivers side only. Technically only found on 1968-70 Mercury Cougar and Ford Mustang. Can be added to a 1967, if adding a passenger side...
Used driver side torque box gusset for any 1971-73 Mercury Cougar or Ford Mustang. It is the reinforcement bracket that attaches to the bottom of the torque box and frame rail for extra strength. Sold individually. This part is removed from a parts car, you will need to drill out spot welds and clean up the edges prior to installation. This is for the drivers side only. Replaces Ford part number D1ZZ-65100A15-A.
Used passenger side torque box gusset for any 1968-70 Mercury Cougar or Ford Mustang. It is the reinforcement bracket that attaches to the bottom of the torque box and frame rail for extra strength. Sold individually. This part is removed from a parts car, you will need to drill out spot welds and clean up the edges prior to installation. This is for the passenger side only. Technically only found on 1968-70 Mercury Cougar and Ford Mustang. Can be added to a 1967, if adding a passenger side...
Used passenger side torque box gusset for any 1971-73 Mercury Cougar or Ford Mustang. It is the reinforcement bracket that attaches to the bottom of the torque box and frame rail for extra strength. Sold individually. This part is removed from a parts car, you will need to drill out spot welds and clean up the edges prior to installation. This is for the passenger side only. Replaces Ford part number D1ZZ-65100A14-A.
Welded in hooked retainer for the rear seat back installation on any 1967-73 Mercury Cougar or Ford Mustang coupe or hard top body style. This bracket welds to the edge of the package tray. Two hooks per car, sold individually. We cut out a individual sections as shown. Make good measurements prior to removal of your old brackets. You will need to drill out the spot welds prior to installation. For sure that basic Ford part number is 62118.
New inner floor frame support for the Mercury Cougar and Ford Mustang.
If you are buying our one piece Mustang floor pan or our driver side rear extended floor pan, you will find they line up great until you come to the area where it meets the wheel house. The inner Wheel house is very different Mustang vs. Cougar and this used custom cut will be needed if your existing pan needs replaced all the way to the wheel houses. If you need more material than what is shown contact us with a picture of your needs and we can cut to suit. ...
If you are buying our one piece Mustang floor pan or our driver side rear extended floor pan, you will find they line up great until you come to the area where it meets the wheel house. The inner Wheel house is very different Mustang vs. Cougar and this used custom cut will be needed if your existing pan needs replaced all the way to the wheel houses. If you need more material than what is shown contact us with a picture of your needs and we can cut to suit. 1969-70 Mercury Cougar. ...
If you are buying our one piece Mustang floor pan or our passenger side rear extended floor pan, you will find they line up great until you come to the area where it meets the wheel house. The inner Wheel house is very different Mustang vs. Cougar and this used custom cut will be needed if your existing pan needs replaced all the way to the wheel houses. If you need more material than what is shown contact us with a picture of your needs and we can cut to suit. ...
If you are buying our one piece Mustang floor pan or our passenger side rear extended floor pan, you will find they line up great until you come to the area where it meets the wheel house. The inner Wheel house is very different Mustang vs. Cougar and this used custom cut will be needed if your existing pan needs replaced all the way to the wheel houses. If you need more material than what is shown contact us with a picture of your needs and we can cut to suit.1969-70 Mercury...
Floor tunnel body reinforcing plate for the floor shifter on any 1967-68 Mercury Cougar or 1965-68 Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than other years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel. Ford part number C5ZZ-6512118-A.
Floor tunnel body reinforcing plate for the floor shifter on any 1969-70 Mercury Cougar or Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than previous years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel. Ford part number C9ZZ-6512118-A.
Floor tunnel body reinforcing plate for the floor shifter on any 1971-73 Mercury Cougar or Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than previous years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel. Ford part number D1ZZ-6512118-A.
Reproduction driver side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps ...
Reproduction passenger side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps. ...
Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...
Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...
Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 4 total per car, all 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped for the front seat belts inboard on 1971-73 cars. Round anchor bracket with factory welded nut for added strength. See related items for good used seat belt anchor plates if you have concours needs. Replaces Ford Part # D1AZ-6561216-A. ...
This seat riser / platform is specific to Mustang, but if you're "vertically challenged"....you may want to go ahead and use this part on your Cougar. It'll raise your seat up enough so that you don't have to use phone books anymore!
These are exact replacements for the 1964-68 Ford Mustang, but looks similar to the pans for the 1967-68 Mercury Cougar. These floor pans will also fit the 1969-73 Mustang, but the will requires modification to fit properly. 1969-70 cars have different ribbing configurations and 1971-73 cars can use these also. This is a heavy gauged stamped steel floor pan.Will fit Convertible if upward facing rocker flange is modified. *NOTE* This floor pan has the outside lip bent up which is proper for...
These are exact replacements for 1964-68 Ford Mustang, but looks similar to the 1967-68 Mercury Cougar. This floor pan will also fit the 1969-73 Ford Mustang, but 1969-70 cars have different ribbing configurations. To use this pan in 1971-73 cars will require modification. This heavy gauged stamped steel floor pan starts behind the seat platform.Will fit Convertible if upward facing rocker flange is modified. *NOTE* This floor pan has the outside lip bent down which is proper for coupes,...
This is a reproduction 3 piece non assembled torque box for the driver side on the 69 - 70 Cougar or Mustang Coupe. The benefit of getting a non assembled torque box is that you'll find installation much easier as compared to the pre-assembled boxes. Included are inner and outer panels and gusset. Passenger side non-assembled torque boxes are not available.
Here is our reproduction SPI torque box for the driver side (left hand) of your Mercury Cougar coupe.
Here is our reproduction passenger side (right hand) SPI torque box for your Mercury Cougar coupe.
Driver side (left hand) outer section of the torque box for the Mercury Cougar and Ford Mustang for both coupe and convertible.
Reproduction floor pan firewall extension for the driver side (left hand) of your 67 - 68 Cougar.
These correct floor pan patches are for the 1969-70 convertible and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long and 15 1/4" wide. Great for the person doing a "correct" restoration on their 1969-70 Cougar / Mustang / Shelby.
*The rocker flange on this convertible pan is wrong, it's supposed to face down but they are made like the coupe, facing up. It will need to be modified to make fit correctly* This is our reproduction, uncut, driver side (left hand), long, front and rear floor pan for your Mercury Cougar convertible.
*The rocker flange on this convertible pan is wrong, it's supposed to face down but they are made like the coupe, facing up. It will need to be modified to make fit correctly* This is our reproduction, uncut, passenger side (right hand), long, front and rear floor pan for your Mercury Cougar convertible.