Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

1967 - 1973 Mercury Cougar Body Parts including sheet metal, brackets, fender extensions and other parts found on the body of your Cougar can be found here. Need help? Call 503-463-1130


Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 913-960 of 1659
$0 Price: $506.25

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 31648 -

Reproduction deck lid for the 67-68 Cougar. Exact reproductions of the originals, these deck lids are well fitting and are a perfect replacement for your old rusty lid.  Does not include hardware or lock cylinder, shipped bare. Here's the installation kit for these reproduction deck lids. Keep in mind that this is an oversized package and will most likely have to be shipped through truck freight. Expect to pay up to $250 in shipping charges. ...

$0 Price: $506.25

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 31892 -

Reproduction deck lid for the 69-70 Cougar. Exact reproductions of the originals, these deck lids are well fitting and are a perfect replacement for your old rusty lid.  Does not include hardware or lock cylinder, shipped bare. Here's the installation kit for these reproduction deck lids. Keep in mind that this is an oversized package and will most likely have to be shipped through truck freight. Expect to pay up to $250 in shipping charges. ...

$0 Price: $65.55

Buy Details

Availability: In-Stock Item
Item #: 15484 -

Reproduction driver side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps ...

$0 Price: $65.55

Buy Details

Availability: In-Stock Item
Item #: 15485 -

Reproduction passenger side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps. ...

$0 Price: $100.05

Buy Details

Availability: In-Stock Item
Item #: 12817 -

Good for all 71-73 Cougars and Mustangs. This extension extends from the driver side rear fender apron to the top of the cowl.This rear fender apron extension is a great choice for your damaged, rusted or missing panel. Made from stamped steel, just like the original. The extension fits in place between the passenger side rear fender apron and the top of the cowl. It provides for a sturdy, stable mounting area for the far rear top fender bolt and the rear hood hinge bolts. ...

$0 Price: $100.05

Buy Details

Availability: In-Stock Item
Item #: 12122 -

Good for all 71-73 Cougars and Mustangs. This extension extends from the passenger side rear fender apron to the top of the cowl.This rear fender apron extension is a great choice for your damaged, rusted or missing panel. Made from stamped steel, just like the original. The extension fits in place between the passenger side rear fender apron and the top of the cowl. It provides for a sturdy, stable mounting area for the far rear top fender bolt and the rear hood hinge bolts. ...

$0 Price: $225.77

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32615 -

Driver side, rear frame rail, from a 1969 and 1970 Mercury Cougar hard top. Full length, we cut so that there is some remaining metal on the edges. Ford part number C9WY-6510125-A.* Note - this item has dimensions in excess of 75 inches, and will ship as "Over- Size", unless you pick up in person. ** Note - Convertible is different.

$0 Price: $52.75

Buy Details

Availability: In-Stock Item
Item #: 41633 -

Reproduction driver side rear inner apron for both the Mercury Cougar and Ford Mustang.

$0 Price: $49.15

Buy Details

Availability: In-Stock Item
Item #: 41686 -

Stamped steel driver side (left hand) rear inner apron for the Mercury Cougar or Ford Mustang.Here's a little film to help you fortify your flexxy feline!

$0 Price: $43.65

Buy Details

Availability: In-Stock Item
Item #: 19680 -

Reproduction stamped steel driver side (left hand) rear inner apron for Mercury Cougar or Ford Mustang.

$0 Price: $52.75

Buy Details

Availability: In-Stock Item
Item #: 41629 -

Reproduction passenger side rear apron for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

$0 Price: $50.95

Buy Details

Availability: In-Stock Item
Item #: 41685 -

Reproduction stamped steel passenger side (right hand) rear inner apron for the Mercury Cougar or Ford Mustang.Here's a little film to help fortify your flexxy feline!

$0 Price: $41.85

Buy Details

Availability: In-Stock Item
Item #: 19702 -

Reproduction passenger side (right hand) rear inner apron for Mercury Cougar and Ford Mustang.

$0 Price: $19.67

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 19124 -

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

$0 Price: $16.78

Buy Details

Availability: In-Stock Item
Item #: 15862 -

Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

$0 Price: $19.67

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 19125 -

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

$0 Price: $140.27

Buy Details

Availability: Discontinued, Limited Stock on Hand
Item #: 13806 -

This reproduction fiberglass valance actually is better quality than you might guess... The mold was made from a NOS FoMoCo valance and as you look at the pictures you will notice that every tiny detail was mimicked. This is a good alternative for those trying to shed a few pounds as they are much lighter than OEM and keep in mind our steel reproductions are substantially heavier than OEM.Replaces Ford part # C9WY-6540544-A

$0 Price: $194.27

Buy Details

Availability: In-Stock Item
Item #: 32437 -

Quality reproduction steel rear lower valance for the 1969 - 1970 Mercury Cougar. This Dynacorn reproduction is actually made of thicker stock than OEM. The original's weight is 4.6 lbs and this new reproduction weighs in at 5 lbs. We've tested this valance on a few of our cars and found them to fit exceptionally well. Mounting hardware is sold separate. Also available in fiberglass.Replaces Ford part # C9WY-6540544-A. ...

$0 Price: $39.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 27205 -

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford part # D1WB-6528519, Mercury MPC # D1WY-6528011-A. Do you have questions about your Cat's factory pinstriping? This link may help.

$0 Price: $39.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25322 -

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford part # D1WB-6528518, Mercury MPC # D1WY-6528010-A. Do you have questions about your Cat's factory pinstriping? This link may help.

$0 Price: $38.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24109 -

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

$0 Price: $46.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23429 -

Rear fender splash shield for the driver side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16103-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

$0 Price: $46.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23430 -

Rear fender splash shield for the passenger side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16102-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

$0 Price: $209.88

Buy Details

Availability: In-Stock Item
Item #: 30093 -

Reproduction rear taillight panel lower structure / support for the 67 - 68 Cougar. This is a complete replacement for the factory spot-welded-in panel, not a partial cut. For more info on this new trunk panel, check out this video below:

$0 Price: $27.35

Buy Details

Availability: In-Stock Item
Item #: 41506 -

This area of the door often cracks due to the stress caused by worn out hinges. This twelve piece kit includes six screws and six form fitting washers to reinforce the recessed areas that often crack. If your latch area is badly cracked you will want to purchase the repair kit that requires being welded in.

MSRP:$34.99
$34.99 Price: $33.48

Buy Details

Availability: In-Stock Item
Item #: 14-0001 -

This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...

$0 Price: $32.27

Buy Details

Availability: In-Stock Item
Item #: 12-3008 -

New pair of weld in shock tower reinforcement plates cut from 11 gauge steel (1/8") for the Mercury Cougar or Ford Mustang. It is common knowledge that one of the main design flaws of the early Cougar or Mustang are the shock towers. Because of this design flaw, it is common (even with pampered, low mile, completely stock cream puffs) for the shock towers to have some degree of cracking as they were never designed to fit an oversized wheel and tire package, be cornered hard or handle the heavy...

$0 Price: $75.95

Buy Details

Availability: In-Stock Item
Item #: 14080 -

High quality chrome finish on lever & base. Improved cable for smooth operation. You must have correct trunk latch to use this remote. Detailed instructions included. Look for the trunk latch in our 'related items' tab.

$0 Price: $59.15

Buy Details

Availability: Discontinued, Limited Stock on Hand
Item #: 14085 -

This is an upgrade to the Electronic Trunk Release. Allows trunk to be opened with just the push of a button on two wireless remotes that are included. NOTE: This item requires that you have a latch mechanism equipped with the remote release tab.

$0 Price: $8.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0202 -

This is the round metal threaded disc that attaches the D0ZZ-6523258-A bushing to the door glass brackets. About 1-3/4" in diameter, two each per door glass on a 1970. 1971-73 Mercury Cougar and Ford Mustang use 3 of these for retaining the door channel bracket. Ford part number 384289-S.Click on images to enlarge. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy...

$0 Price: $0.85

Buy Details

Availability: In-Stock Item
Item #: 17294 -

Retainer or keeper for door hinge pins on all 1968-73 Mercury Cougar and Ford Mustang, plus most all other Ford products with a typical door hinge pin. The factory installed the hinges with the pins driven in from the bottom as viewed with the doors installed. Most restorations install the pins from the top so that gravity holds them in. These retainers allow the pins to be mounted concours correctly. You must use a socket or other tool to install. These fit the door hinge pins with 5/16 inch...

$0 Price: $0.90

Buy Details

Availability: In-Stock Item
Item #: 41928 -

Plastic insert with metal locking retainer. Replaces Ford part # C5AZ-6221952-A. NOTE* This clip will need to be squeezed on the clip side in order to obtain a good grip. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

$0 Price: $2.88

Buy Details

Availability: Out of Stock
Item #: 11-0323 -

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

$0 Price: $2.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0445 -

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

$0 Price: $29.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 26143 -

Used, with little to no scratches, suitable for every day driver.

$0 Price: $49.86

Buy Details

Availability: Out of Stock
Item #: 30609 -

Spring steel clip located under the drive cable housing as seen on page 16, figure 19 of our free download of the sunroof panel service procedure manual.

$0 Price: $169.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 30480 -

This strip has a series of seven retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.

$0 Price: $169.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32915 -

This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.

$0 Price: $27.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 18537 -

Used grade A side mirror retaining nut for the 1968 Mercury Couga or Ford Mustang. Grade A's will have no scratches or dings.Ford part number C8ZZ-17B719-A

$0 Price: $44.85

Buy Details

Availability: In-Stock Item
Item #: 26152 -

Good grade "A" used nut with minimal scratches from removal process. The originals have deeper grooves and have a better luster on the chrome than the reproductions. This is a one year only design. Don't forget to check out our special tool used to remove and install this nut.

$0 Price: $9.86

Buy Details

Availability: Out of Stock
Item #: 31504 -

Used grade A side mirror retaining nut for the 1968 Mercury Couga or Ford Mustang. Grade B's will have minor scratches or dings. Ford part number C8ZZ-17B719-A

$0 Price: $20.88

Buy Details

Availability: Out of Stock
Item #: 14398 -

Functional used nut with heavy scratches. The originals have deeper grooves and have a better luster on the chrome than the reproductions. This is a one year only design. Don't forget to check out our special tool used to remove and install this nut.

MSRP:$21.99
$21.99 Price: $21.47

Buy Details

Availability: Out of Stock
Item #: 26149 -

Replaces the original Ford part that features a # C7SB-17B732-A casting number. Basically correct for 1967 but works just as well on 1968 mirrors. These nuts are are not 100% correct for a 67 or 68, kind of a mixture of both.Very nice chrome quality at a reasonable price. NOTE: Our mirror nut removal tool works & fits perfectly with the original mirror nuts. However, you will find the tool will NOT fit this reproduction nut properly, it will require that it be filed a...

$25.00 Price: $27.35

Buy Details

Availability: In-Stock Item
Item #: 14368 -

Replace that stripped or scarred retaining nut. This one is unique for your 1969 with remote mirror. Used on multiple FoMoCo applications starting in 1966 on the Mercury Comet. Replaces Ford Part #: C6GY-17B719-A.

$0 Price: $29.15

Buy Details

Availability: In-Stock Item
Item #: 31671 -

This mirror nut for the 70 - 73 Cougar or Mustang is made from stainless steel, as compared to the other reproduction we offer which is made from die cast metal. A few benefits of the stainless steel nut is that the finish on it will not tarnish over time, and that it cannot be cross threaded.

MSRP:$4.99
$4.99 Price: $0.95

Buy Details

Availability: In-Stock Item
Item #: 10665 -

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

$0 Price: $1.95

Buy Details

Availability: In-Stock Item
Item #: 26206 -

Correct rivets for use after you have painted your car or installed a new door. No special tools needed for installation. Simply lightly tap the center recessed portion with a small bolt or blunt punch. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com. Sold as a pair. Replaces Ford Part #: C5ZZ-6223000-A or 354921-S.