Body

Good used Western part that is not bent or heavily rusted and the left is the same as right. Ford master part # D1WY-16B134-A.

Looped weld in retainer for the rear seat installation on any 1967-70 Mercury Cougar. This is the front bracket that holds in the rear seat and was used on both coupes and convertibles. We cut out a section of the floor under the rear seat as shown. Make good measurements prior to removal of your old brackets. We think that the Ford number is C5AZ-6263370-B, but we have not been able to verify this for certain. For sure that basic Ford part number is 63370. ...

Hook bracket weld in retainer for the rear seat installation on any 1971-73 Mercury Cougar. This is the front bracket that holds in the rear seat and was used on both coupes and convertibles. Sold individually, two required per car. We cut out a section of the floor under the rear seat as shown. Make good measurements prior to removal of your old brackets.  The Ford number is C9AZ-6263370-A.

New Old Stock. This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

This is our reproduction, uncut, driver side (left hand), long, front and rear floor pan for your Mercury Cougar convertible.

This is our reproduction, uncut, passenger side (right hand), long, front and rear floor pan for your Mercury Cougar convertible.

Reproduction full length driver side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years. Hi, and sincerely thanks for all help I've received from WCCC during my (mega) 1968 restoration project. If everyone would be that helpful, the world would be a much better place. ;-) My car is almost ready for the road, but - as always - there...

Reproduction full length passenger side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years.

This fusible link is a section of wire connecting the starter solenoid on one end and wiring harness that passes through the firewall to mate with the top switch wiring. Correct for power sunroof equipped Cougars. May also work for XR7 and Standard convertibles.

NOS C7ZB-6522449-A Driver side small size pad or gasket for the exterior door handle. Driver side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.

Replaces Ford part #D1AZ-6522428. Sold individually.

NOS C7ZZ-6522428-A Passenger side large size pad or gasket for the exterior door handle. Passenger side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.

NOS C7ZB-6522448-A Passenger side small size pad or gasket for the exterior door handle. Passenger side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.

Door lock and trunk lock gasket as found on all 1969-73 Mercury Cougar. Gasket used to seal the lock cylinders to the exterior door on all 1967 - 1973 Mercury Cougar and Ford Mustang as well as the trunk lock gasket on all 1969-73 Mercury Cougar. It is not used for the trunk lock cylinder on the 1967 - 1968 Mercury Cougar because they uses a flip up trunk lock cover that instead uses a gasket between the covers housing and the trunk. Replaces Ford part #C7AZ-6243625.

This gasket is found behind the trunk lock housing, which the lock itself sits in behind the trunk lock cover plate, and forms a seal between the trunk lock housing and the trunk itself. Made of soft rubber much like the original. Replaces Ford part #: C7WY-6543625.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Made from durable black plastic with correct ridged edges. Includes all four gaskets, enough for both the left and right exterior door handles. Replaces Ford part numbers C7ZZ-6522428/9.

Premium quality, exact fit plastic gasket set for both the driver and passenger side door handles. Also fits 66-71 Ford Fairlane and 70-71 Cyclone / Torino as well as several other Mercury, Ford Lincoln models. We are the exclusive retailers in the U.S. for this quality kit.

These 1969-70 Mercury Cougar chrome door handle gaskets are the closest fit to the original Ford gaskets on the market. 4 pieces as shown, enough for both door handles only, round lock gaskets sold separately.Will also work on 70-71 Cyclone and Torino.

Replaces Ford part #C9ZZ-6344228, sold as a pair. This is our economy version.

These are Concours quality with correct bevel and markings.. Sold as a pair.

Used original Golde sunroof gear box. This box is found above the headliner on the passenger side.Golde part number 0142850 00

Insert to replace the worn rubber and felt channel guide for the door glass in your cool Cat or precious Pony. These units feature original looking felt. Top molded pieces are bonded securely and has steel inserts for added strength. Sold in a pair. There are three brands of this particular piece, we carry the best even though our price is less than most everyone else. Replaces Ford part #C7ZZ-6521546-A and C7ZZ-6521547-A. Check out our handy diagram below to find other '67-'68 door parts you...

Very rare to find one of these that has never been tapped in the slightest. We have a very limited quantity of grade A centers in stock. Ford part # C7WY-8A047-A. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

The majority of our centers look like the rust free part you see pictured. They will need some minor body work before paint. We will not send you junk! Ford part # C7WY-8A047-A. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

Used driver side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

Used driver side grille assembly found in all 1970 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1971-73 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the driver side of 1971-73 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

Used driver side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

Used passenger side grille assembly found in all 1970 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1971-73 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the driver side of 1971-73 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

Used passenger side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

Used passenger side grille assembly found in all 1970 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1971-73 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the driver side of 1971-73 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

Used passenger side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

Reproduction pair of grille assemblies found in all 1970 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Replaces Ford part numbers D0ZB-65280B62-A and  D0ZB-65280B63-A

This is the 1.37" X 1.66 X .31 plastic grommet that goes inside the trunk to protect the trunk wires from rubbing the edges of the sheet metal body. This grommet was also used for the hood light wiring under the hood.

Used grommet for protecting the trunk light wiring as found on 1967-70 Mercury Cougar and Ford Mustangs. Ford part number C4AB-14603-A.

Used chrome end for the grab handle found on Mercury Cougar XR7 and several other Lincolns like the Continental MK III. Seldom will these be perfect, most have some pitting on the top sides. Fortunately they can be switched end for end and the pitting side can be installed downward. These units are sold individually.Mercury part # C9MB-5422668-A or D0MB-5422668-A.

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Our used handles do not come with this linkage part so if yours is missing this is what you need. Comes with mounting screw as shown.

Reproduction LIGHT BLUE Interior Headliner for the 1967 Mercury Cougar. Correct Moon Crater texture available in most stock colors. This is a VERY light blue used on the early 1967 XR7 with dark blue interior. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark...

Reproduction BLACK Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of installing...

Reproduction BRIGHT RED Interior Headliner found in the very early 1967 Standard Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured)....

Reproduction DARK AQUA Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of...

Reproduction dark ivy gold / dark green headliner for the 1967 and 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Thinking of installing your own headliner? Join in the discussion here for some helpful tips. Check out our video below showing how to install...

Reproduction LIGHT AQUA Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of...

Reproduction interior headliner in light ivy gold / light green for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured)....

Reproduction MAROON / DARK RED Interior Headliner for the 1967 or 1968 XR7 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red and Dark Ivy Gold. Thinking of installing your own headliner? Join in the discussion...

Reproduction MEDIUM BLUE Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of...