Body

Premium grade and quality reproduction floor pan plug. These screw right onto the floor pans prior to the carpet underlay and are much better quality than the originals. The original plugs have rough stampings and are made from galvanized steel. These premium plugs have a smooth cutout and are zinc plated. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford...

Stamped steel floor pan drain caps used to plug oval holes in the front or rear floors. Economy grade reproduction floor pan plug that closely resembling the originals. Complete with rough stampings made from galvanized steel.

Used custom cut driver side roof section of the drip rail for the 67-68 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C7WY-6551701-B

Used custom cut driver side roof section of the drip rail for the 69-70 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C9WY-6551701-A

Used custom cut passenger side roof section of the drip rail for the 67-68 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C7WY-6551700-B

Used custom cut passenger side roof section of the drip rail for the 69-70 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C9WY-6551700-A

This restored driver side (left hand) drip rail moulding / trim for the Mercury Cougar equipped with a vinyl top has had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. These are sold outright, as one side only, or as a pair. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good used...

This restored passenger side (right hand) drip rail moulding / trim for the Mercury Cougar equipped with a vinyl top has had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. These are sold outright, as one side only, or as a pair. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good...

This shim, also referenced to as washers, goes in the clutch portion of the drive gearbox to properly adjust the friction. Three shims (plus a hand crank) were originally supplied with sunroof cars.

This reproduction cowl vent repair panel for the driver side (left hand) of the Mercury Cougar or Ford Mustang addresses a common problem with these old Cats and Ponies. Rust in the cowl. Easy to install on the driver side, but takes more effort on the passenger side, especially if you have air conditioning. These panels are also called fresh air cowl vents or inner cowl vent repair panels. Another way to avoid doing expensive cowl repairs is to purchase our cowl cover.*NOTE*  While...

Only fits Ford Mustang 1969-70.

Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the passenger.

Reproduction electric rear deck / trunk lid release. Includes electric lock latch, control knob and wiring needed to install.Detailed instructions included.

There never was an Eliminator convertible from the factory, but we think there should have been. Since the rear quarter panels are shaped differently, we redesigned the side stripes to fit the contours of the convertible Cougar correctly. Otherwise, these are the same stripes we sell in coupe format, cut from OE-spec 3M Scotchcal vinyl and designed from a NOS stripe kit. The kit includes 17 separate pieces, including all side stripes, hood stripes, rear spoiler stripe, ELIMINATOR rear quarter...

This is our complete black stripe kit for the 1970 Cougar Eliminator. The kit includes 17 separate pieces, including all side stripes, hood stripes, rear spoiler stripe, ELIMINATOR rear quarter panel decals, and the often-overlooked 3-piece rear trim blackout stripes. This is the most correct and complete kit you'll find anywhere. Designed using a NOS stripe kit as a reference, and cut from the same 3M satin black vinyl that Ford used from the factory. *Convertible owners - If you're planning...

Black stripe kit for the 1969 Cougar Eliminator. This is the most correct kit you'll find anywhere. Designed using a NOS stripe kit as a reference, and cut from the same 3M satin black vinyl that Ford used from the factory. Kit includes 8 pieces for the fenders & extensions, doors, and quarter panels.Copy of original Ford decal instructions included. Note that these stripes are supposed to go on in a straight line, they do not curve down with the body line. See car picture in this listing for...

There never was an Eliminator convertible from the factory, but we think there should have been. Since the rear quarter panels are shaped differently, we redesigned the side stripes to fit the contours of the convertible Cougar correctly. Otherwise, these are the same stripes we sell in coupe format, cut from OE-spec 3M Scotchcal vinyl and designed from a NOS stripe kit. Quality and fit are second to none. There was also never a white Eliminator stripe kit in 1970 (unlike 1969) but we figured...

This is our complete white Eliminator stripe kit for 1970 Cougar coupes. There was never a white Eliminator stripe kit from the factory in 1970 (unlike 1969) but we figured we'd make these available for those wanting a custom look. Designed using a NOS stripe kit as a reference, and cut from OE-spec 3M vinyl, fit and quality are second to none. The kit includes 14 separate pieces, including all side stripes, hood stripes, rear spoiler stripe, and ELIMINATOR rear quarter panel decals. Unlike...

White stripe kit for the 1969 Cougar Eliminator. This is the most correct kit you'll find anywhere. Designed using a NOS stripe kit as a reference, and cut from the same kind of 3M vinyl that Ford used from the factory. Kit includes 8 pieces for the fenders & extensions, doors, and quarter panels.Copy of original Ford decal instructions included. Note that these stripes are supposed to go on in a straight line, they do not curve down with the body line. See car picture in this listing for...

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very...

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of all of the 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T.Licensed by FORD

This is the aluminum emblem which mounts on the center of all scuff plates. Features raised script surrounded by "Product Of Ford" like original, adhesive backed and protective coating. Sold individually, two required per car. Replaces Ford part # C8ZZ-6513208-T. Technically this is the version found on 1967 cars, the 1968 versions had a larger blue oval 'Ford', and did not have the 'Product of' line.

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

High quality reproduction adhesive emblem for your deck lid. Measures 6.5" wide by 2.35" tall. It has the correct black paint applied to the sides. If you have a 71-73 Cougar this chrome emblem is a much better match to your other emblems even though it is not technically correct. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think...

Adhesive backed, located on the right side of your deck lid.  We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often, as you can see one of our example photos above, the line workers did not even attempt to get them very well centered. Both emblems were placed on the RH side of the deck lid "somewhat" centered top to...

Holds both both the speedo cable and the parking brake cable in place with two self tapping bolts. Bolts not included, picture is for reference only. Part will have rust, but not severe.Replaces Ford part number 381821-S2 per the Chassis Assembly Manual 1967 page 17, 1968 Page 39.

This is the first bracket to secure the emergency brake cable as it exits the firewall. It mounts to the frame rail. It is held on by one bolt which is not included, picture is for reference only. Part will have rust but not severe.

Grade A door cup (escutcheon) used on both the Xr7 and Decor / Deluxe interiors with moulded door panels. Casting numbers as seen on the back can read D1WB-6522635-A or D3WB-6522635-A. The last 3 digits will read something like -AWA, AWD or similar which denotes the different colors. These resemble Mustang but are in fact unique to the Cougar. Very hard to come by without substantial UV damage. Please denote interior color and we will attempt to send your requested color. Product Condition...

Grade B door cup (escutcheon) used on both the Xr7 and Decor / Deluxe interiors with moulded door panels. Casting numbers as seen on the back can read D1WB-6522635-A or D3WB-6522635-A. The last 3 digits will read something like -AWA, AWD or similar which denotes the different colors. These resemble Mustang but are in fact unique to the Cougar.  Grade B versions will have significant UV damage and will need to be cleaned as best possible and painted. Plastic will be flakey and may be...

Grade B door cup (escutcheon) used on both the Xr7 and Decor / Deluxe interiors with moulded door panels. Casting numbers as seen on the back can read D1WB-6522635-A or D3WB-6522635-A. The last 3 digits will read something like -AWA, AWD or similar which denotes the different colors. These resemble Mustang but are in fact unique to the Cougar. Grade B versions will have significant UV damage and will need to be cleaned as best possible and painted. Plastic will be flakey and may be be...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install.  These are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

This rod bridges the gap between the trunk lock cylinder and trunk latch. It is held in place by the round spring that attaches to the back of the trunk lock cylinder. Ford part number C7SZ-6543283-A. 1967 - 1968 only.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Grade "A" will be perfect with no dings, ready to sand and paint. No surprises, just excellent quality!Ford part # D0WB-16A678-A.

This grade "B"unit will only have a minor ding like the one shown here.Ford part # D0WB-16A678.

New Old Stock grille center extension / surround for the 1970 Mercury Cougar, in the original box from Ford.Ford part # D0WB-16A678-A.

Sold as a Kit as Pictured.

Reproduction Fastener Kit - Deck / Trunk Lid & Hinges for the 1968 Mercury Cougar / 1968 Ford Mustang 

Reproduction fender fastener kit for Mercury Cougar Standard and XR7.

These reproduction hood and hinge bolts and U nuts fir both the Standard and XR7.

This reproduction hood latch and catch screw and U nut kit fits both the Standard and XR7 and is sold as a kit as pictured.

This reproduction hood latch vertical support screw and U nut kit fits both the Standard and XR7 and is s sold as a kit as pictured.

Correct Fit and finish for 1967, and works for 1968. Connects the overhead roof console to the mounting bracket. The only difference between the 67 and 68 kits are that the 67 screws are chrome and the 68 are zinc. The zinc will discolor over time, so we suggest using the 67 kit on a 68. Replaces Ford Part #: 519A58

This reproduction quarter panel extension fastener kit fits both the Standard and XR7.

This kit mounts the wing to the pedestal.

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust and no distorted wheel lip areas from over sized tires rubbing. We really inspect the area where the fender extension bolts...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust and no distorted wheel lip areas from over sized tires rubbing. We really inspect the area where the fender extension bolts...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust, no distorted wheel lip areas from over sized tires. We really inspect the area where the fender extension bolts on well as...