Body

C9WY-14018-A Right side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7 Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

D1AZ-14018-A Door ajar switch found on 1971-73 Mercury Cougar XR7's and part of the Convenience Group package found optionally on standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light. Switch is the same for both doors. This switch was also used on 1972 Lincoln MK IV, and 1972 Ford Thunderbird.Fits 71 Cougar and XR7Fits 72 Cougar and XR7Fits 73 Cougar and XR7Fits 72 Lincoln MK IVFits 72 Ford Thunderbird ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. OEM style door jamb switch to release tilt/tilt-away columns on a 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the steering...

Reproduction one year only switch for the 1968 Mercury Cougar with power sunroof (or 1968 Ford Mustang convertible). The XR7 G used a different switch built into the console but the other Cougars ordered with a sunroof in 1968 had this switch mounted to the right of the steering column under the dash.   Knob and bracket included as shown.

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Sold only as a pair. *NOTE* The 1967 uses a smaller pin assembly and this switch will not work without modification. Replaces Ford Part #: C8AZ-13713-C.

Used corner cut from a 1971-73 Mercury Cougar. This would be the driver side where the quarter extension and bumper filler mount. Really it is two pieces spot welded together to the tail panel, quarter panel, and trunk drop off. These may have some pitting or minor rust in the trunk drop off area. 

Used corner cut from a 1971-73 Mercury Cougar. This would be the passenger side where the quarter extension and bumper filler mount. Really it is two pieces spot welded together to the tail panel, quarter panel, and trunk drop off. These may have some pitting or minor rust in the trunk drop off area. 

This pair of sturdy cardboard taillight covers / protectors are designed to protect your taillight sockets from being dislodged or damaged. In addition to the protection they offer they also serve to give a "cleaner" look to your luggage compartment. Will require minor trimming. Please let us know if you have a good used example so as to use as a template to perfect these parts.

Reproduction taillight panel for the 67-68 Cougar. Yet another in a long line of great fitting parts from our friends over at Dynacorn, this replacement taillight panel is perfect for those of you who have rust holes in and around the taillight area. As seen in the photo above, this is only the taillight panel and will not include the quarter extension panels or the rear taillight lower structure. ...

This is how most of our taillight panels are cut off. If you only need a partial panel we can do that too, just give us a ring. Keep in mind we only cut panels like this if both 1/4's are ruined. It is getting very hard to come up with some of these cuts. ...

This is how most of our taillight panels are cut off. If you only need a partial panel we can do that too, just give us a ring. Keep in mind we only cut panels like this if both 1/4's are ruined. It is getting very hard to come up with some of these cuts. Keep in mind that this is an over sized item and cannot get shipped through USPS, it can only go through UPS. You can expect to pay up to $200 in shipping for this item.

This is how most of our taillight panels are cut off. If you only need a partial panel we can do that too, just give us a ring. Keep in mind we only cut panels like this if both 1/4's are ruined. It is getting very hard to come up with some of these cuts.Click on images to enlarge. ...

Sold as a pair, these cardboard protectors do more than just give your trunk a clean look, they protect your tail light sockets from damage. If you see them advertised for less we want to know about it!

This RAM AIR hood scoop template was created by placing a piece of butcher paper under an original 1969 428 Cobra Jet RAM AIR hood scoop and applying spray paint to the mounting holes and opening. Contrary to what you may have been told, the opening is not supposed to be round, and yes those protrusions you see are in fact correct. The 1969 uses a slightly different cut out than the 1970.

This RAM AIR hood scoop template was created by placing a piece of butcher paper under an original 1970 428 Cobra Jet RAM AIR hood scoop and applying spray paint to the mounting holes and opening. Contrary to what you may have been told, the opening is not supposed to be round, and yes those protrusions you see are in fact correct. The 1970 uses a slightly different cut out than the 1969. If you can make a template for us from your 1968 or 1969 Ram Air Cougar we would love to hear from you! ...

For those wanting to make their own "custom" package tray this will assist you in getting the correct dimensions the first time. This template is traced from a reproduction packege tray onto a piece of butcher paper.

New template to make your own package tray cover for the Mercury Cougar. Package trays are difficult to package and can be costly to ship.  This template will assist you in making your own. *NOTE* There is a slight difference in size between 1967 and 1968 package trays.

New template to make your own package tray cover for the Mercury Cougar. Package trays are difficult to package and can be costly to ship.  This template will assist you in making your own. *NOTE* There is a slight difference in size between 1967 and 1968 package trays.

This listing is for a TEMPLATE which would be used to cut your own shock tower weld in plates. Our supplier made a batch of weld in plates to the wrong thickness, so we're selling this template for anyone who has the ability to fabricate their own. As a stand alone item, this template will not work for what it's indented for because it's too thin. It's made from 18 gauge steel (the actual plates are supposed to be 11 gauge) so they're worth nothing more than being a pattern for the...

This specially machined screw tensions the friction clutch assembly in the gearbox.

These are usually cracked, shrunk or missing. Your visors will constantly fall out of the center holder if these are missing or shrunken. Sold as a pair. Replaces Ford Part #: D1DZ-6204115-A.

This is an upgraded version from what you see in our video but the idea is the same. This tool has a square hole so you can use your 3/8" drive ratchet or breaker bar to get the correct angle and have even better control of your leverage when placing the torsion bar into the slot. Used to remove the hinge springs (torsion rods) off the 1967 - 1973 Cougar or Mustang. No more trying to remove with the wrong tools . These can be tricky to remove without this tool.  Will not work on 1964 -...

Upper toque box patch panel plates for the 67-70 Cougar Coupe or 65-70 Mustang Coupe or Fastback.

Reproduction passenger side (left hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

This is a reproduction 3 piece non assembled torque box for the driver side on the 69 - 70 Cougar or Mustang Coupe. The benefit of getting a non assembled torque box is that you'll find installation much easier as compared to the pre-assembled boxes.  Included are inner and outer panels and gusset. Passenger side non-assembled torque boxes are not available.

Reproduction torque box gusset for your 67 - 70 Cougar or Mustang. It is the reinforcement bracket that attaches to the bottom of the torque box for extra strength. Sold as a pair.

Driver side (left hand) outer section of the torque box for the Mercury Cougar and Ford Mustang for both coupe and convertible.

These long rods are installed horizontally in your trunk and attach to the trunk lid hinges. We only remove these bars in pairs from cars that demonstrate that they can in fact support the weight of the deck lid on their own. We do not save rusty, bent or weak springs. These are the best we have to offer from our Western parts cars. 1967-70 torsion springs C7WY-6544890-A and C7WY-44891-A. Limited to supply on hand. The body section of the shop manuals describe how to adjust these bars, we...

These long rods are installed horizontally in your trunk and attach to the trunk lid hinges. We only remove these bars in pairs from cars that demonstrate that they can in fact support the weight of the deck lid on their own. We do not save rusty, bent or weak springs. These are the best we have to offer from our Western parts cars. 1971-73 Mercury Cougar torsion springs D1WY-6544890-A and D1WY-44891-A. The body section of the shop manuals describe how to adjust these bars, we offer a torsion...

Reproduction transition panel for the 67 - 70 Cougar. This is a complete replacement for the factory spot-welded-in panel, not a partial cut. For more info on this new trunk panel, check out this video below:

Reproduction transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy our used support, as these reproductions are inferior to the originals, and to be honest, they simply do not fit well.

Used transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy this used support as compared to the reproductions. The repros we offer are inferior to the originals, and to be honest, they simply do not fit as well.

Used transmission tunnel specialty cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up with the firewall, floor pans and rear seat area. If you'd like a smaller section, you can tape off the area you're working on and send us a few digital pictures so we can cut to your needs. Pricing may not change, because we're...

Used transmission tunnel specialty cut. From a 1969 Mercury Cougar, slightly different than the 1970 tunnel.File picture of 1967 tunnel, you get a 1969 tunnel cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up with the firewall, floor pans and rear seat area. If you'd like a smaller section, you can tape off the...

Used transmission tunnel specialty cut. From a 1970 Mercury Cougar, slightly different than the 1969 tunnel. The 1970 tunnel has a bump out on the driver side for the manual transmission Hurst shifter clearance. File picture of 1967 tunnel, you get a 1970 tunnel cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up...

Used transmission tunnel specialty cut. From a 1971-73 Mercury Cougar.File picture of 1967 tunnel, you get a 1971-73 tunnel cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up with the firewall, floor pans and rear seat area. If you'd like a smaller section, you can tape off the area you're working on and send us a...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.Clear, high strength adhesive for use with lightweight fabrics and carpets. Heat and moisture resistant.

Reproduction driver side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.

Reproduction passenger side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.

Reproduction driver (left hand) side trunk floor panel with trunk drop off. This is a complete replacement for the factory spot-welded-in panel, not a partial cut.For more info on this new trunk panel, check out this video below:

Reproduction passenger (right hand) side trunk floor panel with trunk drop off. This is a complete replacement for the factory spot-welded-in panel, not a partial cut. For more info on this new trunk panel, check out this video below:

Comes with trunk drop offs and complete tail panel. We would be happy to modify the way in which we remove this part to best fit your needs. Figure about $250 for shipping and crating via www.forwardair.com. Please call to order this one.

Comes with trunk drop offs and complete tail panel. We would be happy to modify the way in which we remove this part to best fit your needs. Figure about $250 for shipping and crating via www.forwardair.com. Please call to order this one.

These reproduction J clips mount to the underside of the deck lid and fit Standard and XR7 trunk lids.

Used cover with dull chrome. This used to be a very sought after and expensive part due to how difficult they were to find. Now that our show quality reproductions are here they have little value... Great for someone that just wants their driver to look complete. Fits all 1967-68 Mercury Cougars, Standard and XR7 models. Decal inserts available separately. ...

For 1967 both the XR7 and Standard model used the decal shown on this reproduction trunk lock cover. For 1968 only the Standard model used this decal as the XR7 and XR7G had their own unique center badging. *NOTE* You will have to apply the licensed by Ford decal to the deck lock cover. Click on images to enlarge. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

This is for the person who already has a decal or XR7G emblem to place in the center section. Maybe you have a custom idea? Same great quality and flawless fit as our other deck lock covers.*NOTE* After a long hiatus these are finally back in stock! They were worth the wait, the quality is really good on this new reproduction.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...