Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Below are some guides that may help you make the most use of the fastener section of our website.
Buy Details
Reproduction intake manifold nut for the 289 or 302 on the 1968 Mercury Cougar and Ford Mustang (and possibly other Ford / Mercury cars). 5/16-18 X .72 X .33 zinc free-spin flanged nut. Sold individually. Replaces Ford part #: 374031-S
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds
Reproduction A/C Tag Retainer for the 1967 - 1973 Mercury Cougar
part # 370608-S. Used in multiple places on mounting brackets.
There are 3 of these acorn nuts used per emblem. They are taller than what was used in 1968.Sold individually.
This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually. These clips attach to posts built in to the car. In case you're missing some...
Ford Part # 379390-s Sold individually
Includes a pair of chrome screw adjusters, nuts and washers, heavy duty plastic rest plates and attaching screws to repair or replace that missing seat back adjustment.Replaces Ford Part #: C1DZ-6461643
Fits 1967 Standard or XR7
This screw / stud seems to always be missing. This screw is just a little longer than stock to accommodate installing the Hi-Po air cleaner. Fits most Autolite carburetors. Size: 4 1/8 inches length 1/4-20 X 5/16-18 threads. Check your thread size on the carburetor, we think that starting in 1969 the Autolite 4300 carburetors had 1/4-20 threads. Please note that this stud has 5/16-18 threads going into the carburetor. Replaces Ford Part #: 370971-A *Note - Check your carburetor, it will...
Sold individually. Used on factory 2V Ford carburetors. Zinc (dark gray)
Reproduction Alternator Connection Nut for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold insividually
Reproduction Alternator Connection Nut for the 1970 Mercury Cougar or Ford MustangSold individually
Reproduction Alternator Pulley Nut for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
Reproduction Anchor Strap - Tape In for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Replaces Ford Part # C8AZ-2B164-A Sold individually
Reproduction apron nuts for the 67 - 70 Cougar or Mustang. These are the fasteners that are imbedded into the aprons on either side of the engine compartment and are used to fasten the hood hinges to the car. Sold in a pack of 6 fasteners.
Sold individually # 374212-S
Fits 1967 and 1968 Standard or XR7
This is a used A/C center vent attaching clip. Two required per center AC vent, the two tiny tabs fit in the holes on the sides of the vent assembly and when you tighten the Phillips screw it will pull the vent tight against the dash pad. Very hard to come by, others have used silicone to bond the chrome vent in place when clips could not be found.Replaces Ford part number C7AZ-14570-A.
Replaces Ford Part # 50828-S Sold individually. Zinc Dichromate (yellow-rainbow)
OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S
Sold individually. Stainless Steel
Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.
Barrel nut for the 3/16" stud found on the 6.5 Liter badge and the GT badges that mount on the fender of 1967 Mercury Cougar and Mercury Cyclone GT with the S code 390 engine. Same GT badge on the 1968 Mustang GT models. Item sold individually. The install is basically the same as shown here: https://youtu.be/mcd788WUNns
Tubular or barrel nut for attaching our reproduction "C" pillar XR7 emblems with studs. We found these fasteners to install the emblems without disturbing the headliner of a 1967-68 Mercury Cougar. These are also suitable for installing this emblem onto the trunk lids of 1971-73 Mercury Cougar XR7 models. The originals were flat backed and glued onto the deck lids with adhesive. These tubular nuts require two 7/32" holes be drilled. These mount on the lower part of the roof behind the...
Fits Standard and XR7
Reproduction Battery Tray Bolts & U Nuts for the 1968 Mercury Cougar / Ford Mustang
These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.
Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"
Reproduction master exterior fastener kit for the Mercury Cougar Standard and XR7. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Fender Splash Shields (front of fender) Fender Splash Shields (rear of fender) Battery Tray Hood and Hinges Cowl Panel Shock Tower Braces Hood Levelers Hood Latch and Catch Fender Extensions Quarter Panel Extensions Trunk Latch...
Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.
Reproduction 289 - 302 Alternator Bolt w- Smog for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold individually
Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!
Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!
Replaces Ford Part # C9OZ-6065-B
Sold individually. Replaces Ford Part # C9OZ-6065-A
Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.
Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.
Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
Sold individually Zinc (dark silver)
Bolts and installation kit for most 1970-73 Mercury Cougar and Ford anything, including Mustang with V-8 engines. Kit includes main pivot bolt and adjusting bolt as shown. Spacer not included, but available used.
Replaces Ford Part # 43260-S Sold individually
New screw with a correct 3/8 inch hex head for installing all armrests for all years.