Plastic Clips

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

This clip is hidden about midway under your console and is used to keep the wire running to the back seat light in place. It attaches to the driver side of the console base. Correct for both XR7 and standard consoles.

Used to hold wiring to the back of the dash.

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible.

Used Front Marker Light Plastic Clip for the 1967 and 1968 Mercury Cougar

Four required per car. *Tip from Andrew Petyak* Found a good product to clean used vacuum lines. Its called Wide White-from Coker tire (or Wesley's White Wall Bleach). Used to clean whitewall tires. Its safe for rubber with no harsh chemicals in it. Cleans up rad hoses without giving them that shiny look. Put small amount in thick cotton towel and gently pull hose through it.

Good used clip used to route the wiring harness along the driver side of the engine compartment.

Used headlight wiring plastic clip for the 1968 Mercury Cougar. 2 per side, mount to the headlight buckets.Ford number 377599-S.

Reproduction vinyl top moulding clip for all factory installed 1971-73 Mercury Cougars and should also work on the 1971-73 Ford Mustangs. These are like the ones that attach under the nail heads. Typically, the vinyl top mouldings for the 1971-73 are aluminum.  These are actually Au-Ve-Co brand part number 11288 which is a replica of a GM part, but these are the closest to the originals as we can find. Even though these are not exact copies of the originals, in our tests...

Known to have been used on 1969-1970 air conditioning boxes to hold a vacuum hose to the actuator.  They can be screwed or bolted to the plenum.   Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Inside diamenter = 1"

Used plastic clip for the Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Cougar owner Mike B. shares that this clip was also used on 1970 Cobra Jets with Drag Pak option. Used to hold the wiring harness behind the factory oil cooler on the radiator core support.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used wire loom plastic clip for the Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Six required per car.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject.

Used Trunk Light Wire Plastic Clip for the 1967 - 1973 Mercury Cougar

Found on the lower radiator core support. 4 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part number 382350-S.

Used plastic clip for the Mercury Cougar or Ford Mustang.

New reproduction wire loom clip for the lower radiator core support.

Found on the lower radiator core support.  4 clips needed to attach the wiring harness and the vacuum hoses for the headlight system. Sold Individually. Replaces Ford part # 383104-S.

Found on the lower radiator core support. 4 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part # 383104-S.

This small detail item is used to hold the console wiring harness to the driver side of the rear console compartment end. It clips to the top of the panel part # C7ZB-65060A74-A . Not for use with the XR7 console.Ford part number C3SB-14A163-B.

Located behind the dash to the right of the steering column.

Reproduction black plastic clip that goes onto the lower center of the firewall of any 1969-70 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the second most common. There is a third clip that is only found on 1969 cars.

Reproduction black plastic clip that goes onto the lower center of the firewall of any 1969 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is only found on 1969 and 1970 cars.

Used black plastic clip that goes onto the lower center of the firewall of any 1969-70 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the second most common. There is a third clip that is only found on 1969 cars.

Used black plastic clip that goes onto the lower center of the firewall of any 1969 Cougar or Mustang. Also found on the back of the instrument cluster on the 71 - 73. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is...

This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash. We think that it is Ford part number 382184.

Reproduction Door Speaker / Courtesy Light Loom Clip for the 1967 - 1968 Mercury Cougar or Ford Mustang

Special fasteners which hold firewall insulator to the firewall. Made of high-quality plastic. Sold in pairs Check out this video

Clip used to route the wiring harness along the driver side of the engine compartment.

Reproduction Large Wire Loop Strap for the 1968 Mercury Cougar or Ford Mustang 

Found on the lower radiator core support. 2 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part number 377359-S.

Found on the lower radiator core support. 2 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part number 377359-S.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Keeps spark plug wires neat and orderly. Mounts on valve covers. Replaces Ford Part #: B8Q-12297-A.

Made of heat resistant black nylon. Keeps spark plug wires neat and orderly.

Used Strap - Large Wire Loop for the 1968 Mercury Cougar or 1968 Ford Mustang

Reproduction Universal Strap / Medium Wire Loom for the 1967 Mercury Cougar or Ford Mustang 

Universal wire loom plastic clip for any application on Cougars or Mustangs, as well as many other models.5" x .26"

Reproduction Tail Light / Trunk Light / Courtesy Light Loom Clip for the 1967 - 1968 Mercury Cougar or Ford Mustang