Engine & Under Hood

Replacement radiator cap for the 1967 - 1973 Mercury Cougar or 1967 - 1973 Ford Mustang. This radiator cap releases pressure when the pressure exceeds 13 pound of pressure.

Concours correct Autolite spark plug wires for any 1968 Mercury Cougar or Ford Mustang with 289 or 302 engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q67 (second quarter 1967) on the 7mm wires. Black spark plug boots on this set.

Small block dipstick tube for the 1968 Cougar and Mustang. Nice chrome finish to catch the eye. Will also fit on 1969 Mustangs with a 302 engine.

Nice reproduction oil dipstick made from all steel, painted Ford engine blue. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals. Replaces Ford part # C7OE-6750-B or C8OE-6750-B.

This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. Air Filter Height (Inches) : 2.35" Air Filter Height (mm) : 59.69 mm Air Filter Bottom I.D. (Inches) : 7.54" Air Filter Bottom I.D. (mm) : 191.52 mm Air Filter Bottom O.D. (Inches) : 10" Air Filter Bottom O.D. (mm) : 254 mm Air Filter Top I.D. (Inches) : 7.54" Air Filter Top I.D. (mm) : 191.52 mm Air Filter Top O.D. (Inches) : ...

Concours correct Autolite spark plug wires for any 1967 Mercury Cougar or Ford Mustang with 289 engines and without smog pump. Black wires with 'Autolite' and 'radio resistance' imprinted on the 7mm wires. Correct black boots angled where needed.

Exact Reproduction 289 Hi-Po Main Cap Set offered by Ford. They are cast and machined here in the USA from the original Ford blueprints. A set consists of caps numbered 1- 4 and requires the use of an original rear main cap to finish an engine. These caps are cast from the highest quality Nodular iron and machined for ease of fitting to any 289 block. The I.D. of the main bearing bore is .020 undersize and the side registers are .010 oversize on each side for proper adjustment before line...

Original design in chrome. Beautiful fit, a really nice part. Replaces Ford part # C6AZ-6754-C.

Decal Text: Autolite EV-68C D3OZ-6A666-A Replaces Ford Part #: D3OZ-6A666-A.

Decal Text: Autolite EV-50 D0AZ-6A666-A Replaces Ford Part #: D0AZ-6A666-A.

This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. Air Filter Height (Inches) : 2.51" Air Filter Height (mm) : 63.75 mm Air Filter Bottom I.D. (Inches) : 11.203" Air Filter Bottom I.D. (mm) : 284.56 mm Air Filter Bottom O.D. (Inches) : 13" Air Filter Bottom O.D. (mm) : 330.2 mm Air Filter Top I.D. (Inches) : 11.2" Air Filter Top I.D. (mm) : 284.56 mm Air Filter Top O.D....

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Cork Oil Pan Gasket for the 351 Cleveland Cork Oil Pan Gasket in the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.

Cork valve cover gaskets for any 351C or 351 Cleveland Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Rubber valve cover gaskets for any 351C Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Concours correct Autolite spark plug wires for any 1971 Mercury Cougar Eliminator or Ford Mustang with 351C engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q70 (second quarter 1970) on the 7mm wires. Orange spark plug boots on this set.

Chromed dipstick tube and dipstick for the 351 Cleveland. Average quality part, made in China. Replaces Ford part # D0ZZ-6750-K.

NOTICE: The supplier is no longer making the previous version of the upper hose, and the new hoses will have more of a textured outer wall.  Some Vendors show C8ZE for the upper hose, but C8WE is the correct stamping. These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co, also approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal...

New One-Piece, Rubber Coated Fiber Oil Pan Gasket for the 390, 427 or 428 FE Big Block engine in the 1968, 1969 or 1970 Mercury Cougar and Ford Mustang. 3/32" thick.

Reproduction Big Block Cork Oil Pan Gasket for the 1967 - 1970 Mercury Cougar or Ford Mustang

Reproduction positive crankcase ventilation valve or PCV valve for 1967 Mercury Cougar, Cyclone, Ford Mustang and Torino all with 390GT or S code 390-4V engines. This valve has a stamped casting number of C7AE-6A666-B, comes with a white plastic ring as shown. Ford engineering number C7OZ-6A666-A. Also used on 1967 Shelby Mustang GT500, Ford 428PI, and Mercury Cougar GT-E 427-4V engines. *Note - Must be used with either a reproduction or original 90 degree PCV adapter. ...

Concours correct Autolite spark plug wires for any 1969 Mercury Cougar Eliminator or Ford Mustang with 390 or 428CJ engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q68 (second quarter 1968) on the 7mm wires. Black spark plug boots on this set.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds

Decal Text: Autolite EV-1 C7OZ-6A666-A Replaces Ford Part #: C7OZ-6A666-A

Spark Plug Wire Separator Brackets for the 1969 - 1970 Mustang Cougar or Torino with 428CJ Finned Aluminum Valve Covers, 1969 - 1970 Mustang Boss 302 with Finned Aluminum Valve Covers or Boss 351 models. These are an MCA approved unit made here in the USA. These replace Ford part number C9ZZ-6583-A and include both brackets and the 4 screws to properly install these units. Attaches spark plug wire holder to the factory finned aluminum valve covers

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Concours correct Autolite spark plug wires for any 1969 Mercury Cougar or Ford Mustang with 428CJ engine with thermactor smog system. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q68 (second quarter 1968) on the 7mm wires. Orange spark plug boots on this set.

Decal Text: Autolite EV-45 C8OZ-6A666-B Replaces Ford Part #: C8OZ-6A666-B.

Replaces Ford Part #: EV-51 or D0OZ-6A666-A

Good used rubber ram air seal for any 1968-70 Mercury Cougar or 1968 Ford Mustang. May have some warpage issues. 

This is the reproduction bare metal oil pan for the 1971 Merucury Cougar and Ford Mustang equipt with the 429 big block. Does not include drain plug or a baffle.

This is a reproduction bare metal oil pan with a baffle for the 1971 Mercury Cougar or Ford Mustang and a 429 big block. Includes the drain plug.

These are the best CONCOURS radiator hoses on the market. Made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co. Features special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Imprint is CONCOURS correct for the specific application year includes the Autolite logo. Hoses are also approved by Ford Motor Co. Replaces...

Cork valve cover gaskets for any 429 or 460 Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

New rubber oil pan gasket for the 1971 Mercury Cougar or Ford Mustang when equipped with the 429ci engine. Rubber/Steel Core, 3/32" thick.

Rubber valve cover gaskets for any 429 or 460 Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Reproduction 7-blade fan, fan clutch, fan to clutch bolt kit, and water pump to clutch bolt kit for the 67 - 70 Cougar and Mustang. This kit can  be used to upgrade any 67-70 Cougar/Mustang small block that already has a 24" radiator to the big block cooling fans. Also keep in mind our 1968-1970 big block clutch fans will fit a multitude of Ford products throughout the 1960's and 1970's, including but not limited to Galaxy, LTD, Ranchero, Marquis, Parklane, Cyclone,...

Unique for the 1969 351 Windsor engines without air conditioning. Flat steel bar stock spacer that positions the power steering pump a measured distance away from the cylinder head. The bars are 3-3/8" x 3/4" x 1/2" in size. The threaded hole in the center is tapped 3/8-16. The two outer holes for attaching to the cylinder head are 11/33" holes on a 2-9/16 inch center. Verify the pre-tapped holes in your cylinder head if making your own spacer. For 1970, a round spacer was used, as could be...

Unique for the 1969 351 Windsor engines without air conditioning. Flat steel bar stock spacer that positions the power steering pump a measured distance away from the cylinder head. The bars are 3-3/8" x 3/4" x 1/2" in size. The threaded hole in the center is tapped 3/8-16. The two outer holes for attaching to the cylinder head are 11/33" holes on a 2-9/16 inch center. Verify the pre-tapped holes in your cylinder head if making your own spacer. For 1970, a round spacer was used, as could be...

The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...

Perfect fit for your 289, 302, or 351w with or without AC but a hard sell when our good used rust free brackets cost less . . .

Used alternator adjusting bracket for early 1967 Mercury Cougar or 1965-67 Ford Mustang with 289 V-8 engines. Very early style which is a carryover from the 1965-66 289 alternator bracket. The difference of this C5AE-10145-A alternator bracket and the C7OE-10145-A bracket is the C7OE bracket has a slightly rounded off end to prevent contact with some of the larger diameter water pump pulleys. To be safe, we recommend the C7OE-10145-A bracket for clearance purposes. Ford part number...

Used alternator adjusting bracket for any 1967-68 Mercury Cougar or 1967-68 Ford Mustang with 289 or 302 V-8 engines. C7OE-10145-A stamped bracket has a slightly rounded off end to prevent contact with some of the larger diameter water pump pulleys from previous years. Ford part number C7OE-10145-A.*Trivia - All 3 small block alternator adjusting brackets from 1965-1969 will fit most all 289 / 302 / 351W engines unless your engine has one of the larger pulleys. ...

Ford started using this alternator adjusting bracket sometime in 1973. It mounts to the rear of the alternator. Fits any 1973 Mercury Cougar and Ford Mustang and likely many other Ford cars with 351 engines. It works with the 1970-73 front mounting bracket. Replaces Ford part number D3AE-10145-C.

Used alternator adjusting bracket for any 1969 Mercury Cougar or Ford Mustang with 351W V-8 engines. This C9OE-10145-A stamped bracket is correct for all H or M code 351 Windsor engines. Will also fit 1969 F code 302 Ford engines too.Ford part number C9OE-10145-A.*Trivia - All 3 small block alternator adjusting brackets from 1965-1969 will fit most all 289 / 302 / 351W engines unless your engine has one of the larger pulleys. ...

Used alternator adjusting bracket for any 390 engine 1968-69 Mercury Cougar or Ford Mustang without factory smog. Specifically this is for 1968 390-2V or X code engines, and 1969 390-4V or 390IP engines offered in 1969 cars with S code designation. Replaces Ford part number C8AE-10145-A.This is the 411 for 1968-69 alternator mounting on Mustang and Cougar with 390 engines. If your 1968 S code car (390GT or 390-4V) was delivered in the United States (meaning not Canada or other foreign...