Under Hood / Non Engine

This is a replica of the warning tag that came on positive (+) terminal of Autolite batteries when the 1967 - 1972 Cougars and Mustangs were shipped from the factory.

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. Standard Draw pictured above, High Draw pictured to the left. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part # : C7ZZ-14300 ...

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. For 1972-73 Mercury Cougar and Ford Mustang all with V-8 engines.Positive cable is 10 1/4" center to centerNegative cable is 42" center to centerGround wire is 41" center to center Replaces Ford Part # :...

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. For any 1970-71 Mercury Cougar or Ford Mustang with 302 or 351 engine and 43-55 AMP alternators. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces...

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. For all 1972-73 Mercury Cougar or Ford Mustang with 43-55 AMP alternators and V-8 engines. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part...

Each of these great OEM Style kits include all three required cables, proper terminal and post clamp ends. Unlike CONCOURS CORRECT cables, these do not have the Ford part numbers on them. Starter cables are properly shielded from heat. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) NOTE: These cables are technically correct...

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part # : C8ZZ-14300

This battery cover is designed to be used with any maintenance free flat top battery **24/60 series with original terminal location for the Autolite battery covers.

Reproduction "Battery OK" Decal for the 1967 - 1982 Mercury Cougar / Ford Mustang

Fits Standard and XR7

Perfect fit the first time. You will be happy with this Group 24, quality reproduction and check out the price! These battery trays are a popular item for restorers since most of the originals have been destroyed by leaking batteries over the years. Replaces Ford part #: C7ZZ-10732-D.

This is what I consider to be "Premium Quality". Very correct in every detail and made in the US! The group 27 larger tray was optional on any Cougar and standard on big block Cougars. Replaces Ford part # C9ZZ-10732-AR

NOS service replacement battery tray, may not be exactly like the assembly line tray. Group 27 battery tray is typical for cars with air conditioning and higher amp alternators. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars.  Replaces Ford Part #: D0OZ-10732-B.

Exactly like the originals. This group 27 battery trays are a popular item for restorers since most of the originals have been destroyed by leaking batteries over the years. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars. Supplier misidentifies this part as D1ZZ-10732-B. Replaces Ford Part #: D0OZ-10732-B.

Concourse Correct with 22 & 24 series batteries for Mustang, Cougar and Shelby GT350/500 made in the USA by Mansfield Mustang to orig. Ford Specs includes attaching bolts Replaces Ford Part # C8ZZ-16060-A

Concourse Correct with 22, 24 & 27 series batteries for Mustang, Cougar and Shelby GT350/500 made in the USA to original Ford Specifications, includes attaching bolts. Replaces Ford Part # C9ZZ-16060-A or C9ZZ-16052-P .

Concourse correct with 22 & 24 series batteries for Mustang, Cougar and Shelby GT350/500 made in the USA by Mansfield Mustang to orig. Ford Specs includes attaching bolts Replaces Ford Part # C7ZZ-16060-A

Reproduction Battery Tray Bolts & U Nuts for the 1968 Mercury Cougar / Ford Mustang

Kit comes complete with J bolts and mounting nuts. Replaces Ford Part #: D0AZ-10756-K.

Fastens the battery tray to the fender apron.

Billet aluminum batter hold down bracket for all 1967-70 Mercury Cougar and Ford Mustangs. Maximum battery width 6-3/4 inches. We also have stainless steel hold down bolts available.

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Replaces Ford Part #: D0OZ-10757-A.

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Original used bracket, not reproduction. Replaces Ford Part #: D0OZ-10757-A.

Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.

This is the correct battery hold down clamp for the 1971, 1972 or 1973 Mercury Cougar & Ford Mustang. Ford Part #: D0OZ-10718-B. Note: The battery hold down clamp offered by many Mustang / Cougar vendors as "Concours Correct" is actually for the 1974 - 1978 Cougar /  Mustang.

Includes battery clamp and bolts required to mount battery on tray. Please note that vinyl coating will almost always crack along edges shortly after installation.

These original hood blanket clips grip much better than the reproductions. Usually there were 10-11 of these clips used but it can vary from car to car as they tended to be inconsistent at the factory on how many of the available holes they actually stuck a clip into. Sold Individually.

Reproduction rubber seal for the top of the brake fluid reservoir on the drum brake equipped Mercury Cougar or Ford Mustang. Also fits 1967-71 Ford or Mercury full and mid sized cars, and 1970-73 Maverick and Comet.  Replaces Ford part # C9AZ-2167-B.

Reproduction disc brake master cylinder cap for the Mercury Cougar or Ford Mustang. This unit has the correct stampings, rubber inner gasket, and is considered show quality. This cap will only fit master cylinder part # 15298.Replaces Ford part # C7AZ-2162.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang / Torino1968 Ford Mustang / Torino 1969 Ford Mustang / Torino 1970 Ford...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Not correct for 1967 but works as a functional substitute. This vacuum reservoir mounts under the battery tray for factory tilt swing away steering columns found in the Mercury Cougar or Ford Mustang / Thunderbird. Note that some 1968 Mustangs (without air) mount this tank on the passenger side rear apron. This is a double nipple tank, we also sell the single nipple tank for the...

After-market exact reproduction of the original Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a gravity switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

Reproduction 390GT Engine Lift Hooks for the 1967 Mercury Cougar and Ford Mustang. Also fit 1966-67 Ford Fairlane and 1967 Shelby GT-500, and 1966-67 Ford / Mercury 428 Police Interceptor engines.Ford number C6OZ-17K004-A.

Reproduction plastic battery hold down for the Mercury Cougar or Ford Mustang. According to the Master Parts Catalog, late 1969 through mid 1970, Cougars and Mustangs used these black plastic units. Late 1970 used the same as the 1971-73 model.Replaces Ford part # D0DZ-10718-A.

Used plastic battery hold down for the Mercury Cougar or Ford Mustang. According to the Master Parts Catalog, late 1969 through mid 1970, Cougars and Mustangs used these black plastic units. Probably introduced at the same time in very late 1969 as when the hold down clip was used to attach to the battery apron? Replaces Ford part # D0DZ-10718-A and casting number D0DB-10755-A. 

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

This item has been discontinued until further notice.Basically correct looking except for screws in place of the rivets. The High or Low tone is indicated in raised letters located on the perimeter of the horn. Replaces Ford Part #: C9ZZ-13832 / C9ZZ-13833 or C9ZF-13801-B / C9ZF-13802-C.

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position. We do offer the correct used Cougar horns.Replaces Ford Part # C7ZZ-13832. These horns are close but not correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B...

This item has been discontinued until further notice.The High tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13832 or C9ZF-13801-B.

This item has been discontinued until further notice.The Low tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13833 or C9ZF-13802-C.

Attaches behind the drivers side horn on all 1969-70 Mercury Cougar and Ford Mustangs with air conditioning. We believe that this part was installed to maintain clearance with the A/C condenser. Ford part number C9ZF-13925-A as seen in the 1969 Electrical Assembly Manual.

Tested and working used pair of Hi and Lo tone horns. 1967-68 Mercury Cougar used part number C7WF-13802-B and C7WF-13801-B. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for your show car.NOTE* - Hi tone = passenger side / Low tone = driver side

This is the bolt to hold the battery onto the battery tray. Battery hold down bolt only. Sold individually. Replaces Ford Part # : D0AZ-10756-A

Stainless steel battery hold down bolts. Work with standard battery hold down brackets and the billet hold down bracket.

This engine compartment lamp assembly includes lamp socket, bracket, mercury switch, and length of wire. A bit of investigation shows us that an inline fuse was used on the single wire and it has an amp rating of 7.5 amps.Replaces part # C9WY-15702-A

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

This is a good quality non-concours starter solenoid. Inexpensive replacement if you are not worried about being 100% correct. Disappointing quality, often will fail in less than a year, we recommend buying original FoMoCo. Replaces Ford part # B6AZ-11450-A, C7AZ-11450-A & D2AF-11450-A.

Just about the only possible reason to put this poor quality reproduction on your Cougar is that it is a good tool to put out engine fires. No Joke! If you happen to have an engine fire you can carefully open your hood, yank the blanket downward and smother the fire by pushing the blanket tight around the area that is burning. This can at least buy you time until a fire extinguisher is located. How do I know? I saved a very pristine 1974 XR7 a few years ago this way! This inexpensive product...

Just about the only possible reason to put this poor quality reproduction on your Cougar is that it is a good tool to put out engine fires. No Joke! If you happen to have an engine fire you can carefully open your hood, yank the blanket downward and smother the fire by pushing the blanket tight around the area that is burning. This can at least buy you time until a fire extinguisher is located. How do I know? I saved a very pristine 1974 XR7 a few years ago this way! This inexpensive product...