Intake Manifolds

Used intake manifold bolt for the Mercury Cougar or Ford Mustang equipped with the 351C engine. This item is sold individually.Ford part # 56145-S.

Reproduction intake manifold bolts for the Mercury Cougar Eliminator or the Ford BOSS Mustang equipped with the 302 BOSS engine. These units are sold individually.Replaces Ford part # 56146-S.

Set of 12 bolts for the intake manifold on any factory 1966-67 Ford 289 engine. AMK F-478.*Note - Excludes 1968 289 and 302 engines.

Set of (12) 2 1/16" bolts / studs and nuts for the intake manifold on any factory 1968 Ford 289 or 302 engine. AMK F-479. *Note - Excludes 1967 289 engines.

Set of 12 bolts for the intake manifold on any factory 1970-74 Ford 351C-2V engine. AMK F-1313.*Note - Excludes 351C-4V and 351W engines.

Set of 12 bolts for the intake manifold on any factory 1970-74 Ford 351C-4V engine. AMK F-1321.*Note - Excludes 351C-2V and 351W engines.

Set of 16 bolts for the intake manifold on any factory 1969-70 Ford 351W-2V and 351W-4V engine. AMK F-1131.*Note - Excludes all 351 Cleveland engines.

Set of 10 bolts and several spacers for the intake manifold on any factory 1967 Ford S or Z code, 390 engine. AMK F-475.*Note - Excludes 1968 1969 1970 - 390 and 428CJ engines.

Set of 12 bolts / spacers / stud for the intake manifold on any factory 1969-70 Ford S code 390-4V or 428 Cobra Jet or 428SCJ engine. AMK F-475.*Note - Excludes 1967-68 390 engines.

Set of bolts and studs for the intake manifold on any 1970 Ford 428 Cobra Jet engine. The 1970 set includes a second double ended stud, while the 1969 set only includes 1 double stud. 1970 R and Q code Mustang and Cougar.Trivia - 1970 Mercury Cougars only have a Q as the 5th digit in the VIN code. Yes, All 1970 428 cobra jet Cougars are designated as Q codes. Ram air was optional and will show on the window sticker or Marti Report.

Set of 20 bolts for the intake manifold on any 1970-71 Ford 429 Cobra Jet engine. 429CJ engines were optional in only in 1971 on Mercury Cougar and Ford Mustangs. Available in 1970 on B body Torino, Cyclone, Ranchero, Fairlane. *Note - Excludes Boss 429 engines.

Set of 20 bolts / studs, and nuts for the intake manifold on any factory 1968 Mercury Cougar GT-E 427-4V or 1968 Shelby GT-500 all with aluminum Police Interceptor intake manifold from Ford. AMK F-479.*Note - Excludes 1967 GT-500.

5/16-24 hex nut 7/16" head that is used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts. Sold individually. AMK B-12786

This is a set of four 7/16 nuts that are used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts. 

This is the complete eight piece kit that includes four 7/16 nuts and four studs (1 3/8") which are double threaded. One end is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with NO spacer.

This is the complete eight piece kit that includes four 7/16 nuts and four double threaded studs (2 1/2"). One end of the stud is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with a 1" spacer.

This is the complete eight piece kit that includes four 7/16 nuts and four double threaded studs (1 3/4"). One end of the stud is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with 1/4" to 3/8" spacers.

New reproduction of Ford part number D0OZ-9S500-A, Hi Temperature choke gasket for all 1970-71 429 Cobra Jet engines. Must utilize the stock Ford cast iron 429 Cobra Jet intake manifold. Fits J and C code 1971 Mercury Cougar and Ford Mustang, and J and C code 1970-71 Ford Torino, Ford Ranchero, Mercury Cyclone.*Note - Excludes 429 Super Cobra Jet engines which used a different intake manifold.

Used cast iron choke stove from any 1970-73 351C-2V Ford engine. This is held on with 4 bolts, and to our knowledge no block off plate is reproduced. Casting number on the iron plate is D0AE-9A705-D, which is only for the plate. The plate and coiled tube assembly has a Ford part number of D0AZ-9C869-B. No hardware included.

Used cast iron choke stove from any 1970 351C-4V Ford engine. This is held on with 2 bolts. Casting number on the iron plate is D0AE-9A705-C, which is only for the plate. The plate and tube assembly has a Ford part number of D0AZ-9C869-A. No hardware included. Limited to stock on hand.* Note - for those who do not need the choke stove, a cast aluminum block off plate can be purchased through Summit.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 2 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-2V engines. This gasket set includes a metal pan gasket.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-4V Cleveland engines. ...

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 4 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-4V engines. This gasket set includes a metal valley pan.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-2V Cleveland engines. ...

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1969-73 small block Ford engines with size 351 cubic inches, Windsor engine only. 1969-70 Mercury Cougar and Ford Mustang with 351W engines.Any doubts? 351 windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 289/302 engines. *Note - Excludes 351C or 351 Cleveland engines.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1967-70 big block Ford engines with size 390, 427, or 428 cubic inches, FE engine only. 1967-70 Mercury Cougar, Ford and Ford Mustang.

New gaskets for installing your 429 Cobra Jet intake manifold. This is the Felpro branded gasket. Fits 1970-71 Ford 429CJ engines. 1971 Mercury Cougar and Ford Mustang with J or C code 429CJ engines. Intake to cylinder head gaskets and intake end pieces, along with O ring for distributor. *Note - Excludes N code 429-4V or Thunderjet, passenger car engines.

C6OE-9425-A Cast iron intake manifold used on all 1967 C code 289-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of C6OE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4AZ-9424-H. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance.

C8AE-9425-B Cast iron intake manifold used on all 1968 C code 289-2V, and F code 302-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of C8AE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4AZ-9424-J. The 1966-67 289-2V intake is also a good alternate, see related items for that one.*Installation Tip - A 1 inch aluminum spacer...

C6OE-9425-B Cast iron intake manifold used on all 1967 A code 289-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C6OE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4OZ-9424-G. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance.

Very rare over the counter, Group II dress up accessory item for any 289 / 302 small block engine. In excellent used condition with no cracks, stripped threads or corrosion damage. The nicest you will ever find. This over the counter Intake was marketed by Shelby American in the Cougar catalog titled "How To Sharpen Your Cat's Claws". Shelby casting number S2MS-9424-A. This intake is basically the same one you so often see with COBRA lettering on it. New to our inventory as of 12-15-2017, the...

C8ZE-9425-A Cast iron intake manifold used on all 1968 J code 302-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C8ZE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4OZ-9424-H. *Installation Tip - A 1 inch 4 barrel aluminum spacer plate with PCV provision is needed for proper air cleaner clearance.

D0AE-9425-M Cast iron intake manifold used on all 1970 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of D0AE-9425-M. Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D0AZ-9424-D. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

D1AE-9425-DA Cast iron intake manifold used on all 1971-72 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of D1AE-9425-DA. Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D1AZ-9424-D. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

D3AE-9425-CA Cast iron intake manifold used on all 1973 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of D3AE-9425-CA. Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D3AZ-9424-C. *Installation Tip - A spacer plate with EGR provision is needed for proper installation. *Note - 351 Cleveland engines only. ...

D0AE-9425-E, -H, or -L Cast iron intake manifold used on all 1970-71 M code 351-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0AE-9425-E, -H, or -L . Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D0AZ-9424-C. *Note - 351 Cleveland engines only.

Cast iron intake manifold used on all 1973 Q code 351-4V or 351CJ engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D3ZE-9425-AA . Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D3ZZ-9424-A. *Note - 351 Cleveland engines only. *Installation Tip - A spacer plate with EGR provision is needed for proper installation. ...

C9OE-9425-A or -F Cast iron intake manifold used on all 1969-70 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of C9OE-9425-A or -F. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9OZ-9424-A. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

C9OE-9425-B Cast iron intake manifold used on all M code 351-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C9OE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9OZ-9424-B. Casting number can also be C9OE-9425-D, or C9OE-9425-E. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air...

C6AE-9425-G Cast iron intake manifold used on very early 1967 S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold, used before 1-11-1967. Take off manifold with correct casting number of C6AE-9425-G. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C6AZ-9424-N. This manifold will need to be cleaned and hot tanked prior to use. Current dates available: 6F22, 6L15. *Note -...

C7AE-9425-E Cast iron intake manifold used on 1967 S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold, used before 9-11-1967. Take off manifold with correct casting number of C7AE-9425-E. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C6AZ-9424-K. This manifold will need to be cleaned and hot tanked prior to use. Current dates available: 7A31, 7C27, 7D3,  *Trivia -...

C8AE-9425-A Cast iron intake manifold used on all 1968 S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C8AE-9425-A.  Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C8AZ-9424-A or -B. There is also a C8AE-9425-F version that we offer on another listing.  Current dates available: 7H12, 7H17, 7L10, 7L17,...

C8AE-9425-F Cast iron intake manifold used on all 1968 S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with casting number of C8AE-9425-F. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C8AZ-9424-C. There are other versions of this "S" intake manifold with a suffix "A" letter.  Current dates available: 8A23. *Trivia - One of the heaviest car...

Used C8OE-9425-C Cast iron intake manifold used on all 1969 - 1970 Q and 1968 - 1970 R code 428CJ and 428SCJ engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C8OE-9425-C . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford part number C8OZ-9424-B.  Current date code is 9C25 or March 25, 1969 and 0A19 or January 19, 1970. *Trivia - One of the heaviest...

Reproduction lightweight aluminum high performance intake manifold with the Cobra logo. This is an exact copy of the manifolds Carol Shelby offered on his Shelbys and Cobras in the late 1960's. Fits 260,289 and 302 engines.You can find the SHELBY lettered intake here. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

Reproduction lightweight aluminum high performance intake manifold with the Shelby logo. This is an exact copy of the manifolds Carol Shelby offered on his Shelbys and Cobras in the late 1960's. Fits 260,289 and 302 engines.You can find the COBRA lettered manifold here. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

Reproduction intake manifold valley pan for the Mercury Cougar or Ford Mustang equipped with the 351 Cleveland engine with the 2V (2 barrel) heads.

Reproduction intake manifold spacer for the Mercury Cougar or Ford Mustang equipped with the 390 or 428 engine. Sold individually, # VI.

Replacement steel tube for all FE intake manifolds. Tube connects to water pump via a rubber hose. Fits all FE - 352, 390, 410, 427, 428 engines. Best to replace when intake manifold is removed to drive out the old rotted steel tube. We use a little silicone on the smooth surface prior to installation. The connecting hose (and clamps) to water pump normally got painted Ford engine blue from the factory.