My Lists
Login
Subtotal
$0.00
Shipping
Tax
Discount
Total
*NOTE* According to Phil Parcels of the National Cougar Data Base Project, the approximate cut off VIN for determining EARLY...
This solid state sequential kit eliminates all the mechanical motor-driven sequencers and relays used in the trunks of the...
Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk...
Reproduction dash pad in black for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised...
NOTE: At the moment the supplier is only making the late model version of this beltline kit. The late version has a slight...
Another spot-on reproduction by WCCC! C9ZE-E Applications: 1. All 1969 428 Cobra Jet with and without air conditioning. 2....
Spot-On reproduction from WCCC! C8OE-B Application for 1968 includes all 390-2V, 390-4V, 427-4V, and 428 Cobra Jet engines...
Correct fitting reproduction set of 4 wheel lip mouldings for the 67 - 68 Mercury Cougar Check out this video...
New LED dash light kit for the gauges in your STANDARD 67 - 68 Mercury Cougar. Finally, a kit that will provide you the...
New LED dash light kit for the gauges in your Mercury Cougar. Finally, a kit that will provide you the light you need to see...
This conversion will replace the old, tired, vacuum system that likes to leak and wear out. This kit consists of two BRAND...
This conversion will replace the old, tired, vacuum system that likes to leak and wear out. There are few differences...
Nice reproduction D0OZ-17C583-A windshield wiper stop as found on any 1971-73 Mercury Cougar, 1971-73 Ford Mustang, 1970-71 Ford Torino, or 1970-71 Mercury Cyclone. Zinc plated and rubber dipped...
We shatter the castings from used back-up light assemblies to remove the socket and pigtail complete. This is for the person who has a nice original back up light and is willing to invest the time...
Used and reusable backup lamp socket and wiring assembly for the reproduction reverse light chrome housings or to replace a damaged lead in your original 1969-70 Mercury Cougar reverse light. This...
Used Dash to Gauge Feed Harness for the 1973 Mercury Cougar and Ford Mustang with either the 351C-2V or 351C-4V, Cleveland engine only. Also bundled with the wires is the air conditioning clutch...
Used wire extension for the tilt / tilt away steering column found in the Mercury Cougar or ford Mustang.
This four used piece wiring kit gives you all the factory correct wiring unique to a 1970 XR7 convertible.The rocker switch that raises and lowers the convertible top for the 1970 XR7 convertible is...
This black wire attaches to the fusible link coming off the starter solenoid on one end then passes through the firewall to mate with the top switch wiring at the other end. Correct for both XR7,...
This short section of wiring attaches to the terminal post on the starter solenoid that faces towards the firewall. The other end is a female plug that incorporates a fusible link. If your switch...
This black wire attaches to the fusible link. The Fusible link connects to the starter solenoid with an eyelet connector, then connects to this wire with a billet connector. This wire then passes...
Used wiring cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Unique to the 1968 and 1969 tilt column, fixed column version will not fit on a tilt without...
Used under dash wiring harness fuse block / box (with a chip or two) with wire leads for the Mercury Cougar STANDARD. This is part of the 14401 main under dash wiring harness. The difference between...
Used fuse block / box and pigtail for the under dash harness on the Mercury Cougar. This is part of the 14401 main under dash wiring harness.Ford part # C6OZ-14A068-A.*NOTE* This unit has the same...