General (Old Category Structure)

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Grade "A" hoods have no rust under the lip, nothing more than a light skim coat of filler found anywhere, no damage in the hinge...

Very rare find...NOS Sheet-metal is getting very hard to come by these days. And even at these exorbitant prices we have a hard time keeping many NOS body panels in stock. The best place to find NOS Sheet-metal these days would be at major national swap meets like the All Ford swap meet held in Carlisle Pennsylvania each year in June.Ford part # C7WY-16612-A.

New old stock hood bumper for any 1971-73 Mercury Cougar or Ford Mustang. Sold individually, limited to stock on hand. Replaces Ford part #D1ZZ-16758-A

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. Painted a satin black color. New old stock hood hinge without the spring. These hinges will work for 1970 Cougars, but because the grill center was attached to the hood during this year. The spring is heavier duty than 1967-69.Ford part # C5AZ-16797-B, C8AZ-16797-A, or C9AZ-16797-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. 1978 manufactured date, this one is painted a gloss black color. New old stock hood hinge less spring. These hinges will work on 1970 Cougars, but because the grill center is attached to the hood during that year. The hood hinge requires heavier duty springs to accommodate the additional weight on the hood.Ford part # C5AZ-16796-B, C8AZ-16796-A, and C9AZ-16796-A.Anghel Restorations offers a very detailed...

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped without the spring. These will also work on 1967-70 as well....

This is an extremely rare hood scoop found only on the 71-72 GT and 1971 429 Cougars. This is similar to the 1969-70 scoop, but tapers more in the front so as to follow the unique hood line of the 1971-73 Cougar.Ford part # D1WB-16C664-AA. ...

Reproduction Eliminator hood scoop for the Mercury or Ford. Correct stud configuration, size and weight and far superior to our old scoop we offered. This scoop was made by using an original Eliminator scoop to make the mold. BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. This unit will sometimes crack at the opening. The dimensions are just like the original and measure 21 5/8" at the widest point on the front, 25"...

BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. The Scoop measures 21 5/8" at the widest point on the front, 25" at the widest point at the rear and 26 1/8" tall when stood on end and measured at its longest point. The scoop is 2 7/8" tall at the front middle when mounted on the hood.Ford part # C9WY-16C630-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73...

This original Ford service replacement hood scoop is the same as a factory installed scoop except that it does not have the embossements for the hood grille used on the very first Ram Air Cougars (prior to September 1968) and it has extra mounting stud receptacles for use on multiple applications such as the Comet GT and the Mercury Cyclone. This version does have the reinforcing or webbing like the originals. Ford part # C9WB-16C664-C, C9GB-16C664-C, and D14B-16C664-AA. Found on the bottom. ...

New high quality fiberglass hood for the 1967 - 1968 Mercury Cougar. Inspired by the XR7-G hood scoop, our supplier molded these hoods with this taller functional hood scoop already attached (keep in mind that the original XR7-G and GT-E hood scoops are non-functional). The "nostrils" of the scoop are cut out, and there is a large opening beneath the scoop to provide extra airflow to the engine. This version of the G-Force hood has a molded fiberglass under structure (as...

New high quality fiberglass hood for the 1967 - 1968 Mercury Cougar. Inspired by the XR7-G hood scoop, our supplier molded these hoods with this taller functional hood scoop already attached (keep in mind that the original XR7-G and GT-E hood scoops are non-functional). The "nostrils" of the scoop are cut out, and there is a large opening beneath the scoop to provide extra airflow to the engine. This version of the G-Force hood has a steel under structure that is taken from an original...

D3WY-17K834-A Molded rubber impact strip found on most 1973 Mercury Cougar front bumpers, driver side only. We will seldom have this part in stock, due to its low survival rate and high demand.

D3WY-17K833-A Molded rubber impact strip found on most 1973 Mercury Cougar front bumpers, passenger side only. We will seldom have this part in stock, due to its low survival rate and high demand.

As decades old Cougar lore goes... After Dan Gurney test drove the XR7-G for the first time he was asked what he thought about this new Cougar. His supposed reply was, "you can't hear the horn at high speeds." The car was later equipped with this third horn just for Mr. Gurney. Anyway, that is how the legend goes.  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

This item has been discontinued until further notice.Basically correct looking except for screws in place of the rivets. The High or Low tone is indicated in raised letters located on the perimeter of the horn. Replaces Ford Part #: C9ZZ-13832 / C9ZZ-13833 or C9ZF-13801-B / C9ZF-13802-C.

This item has been discontinued until further notice.The High tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13832 or C9ZF-13801-B.

Tested and working used Hi tone horn. The Hi tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13801-B Hi tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

This item has been discontinued until further notice.The Low tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13833 or C9ZF-13802-C.

Tested and working used Lo tone horn. The Lo tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13802-C Lo tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

Used grade "A" horn center / pad in light blue fro the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can paint it to match your interior. The reproduction center emblem and outer ring can also be purchased separately. *Restoration...

Black paper wrapped aluminum flexible tube that connects the vapor canister to the air cleaner. This is as close to concours as we can find, 3/4 inch diameter, 36 inches long, and black outside, brown paper color inside.  Fits 1970 California Delivered Cars and all 1971 - 1973 Cars. Look for Buck Tag EV or EM. Preheat/Emission Control Duct. Replaces Ford Part #: D1UZ-9d667-A, D4HZ-9d667-A or D0AZ-9D667-A

All 1967 390 Cougars with California emissions. Special molded hose see diagram. Connects the smog pump and air inlet assembly.

Reproduction gas tank to filler pipe hose fits the 67 to 70 Mercury Cougar, measures 4 1/2" long. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

This Pump to Value Outlet Pressure Hose is 100% correct for the 1967, 1968, 1969, 1970 big block. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Replaces Ford Part #: C9OZ-3A319-C.

D3-6A664-4V Original used hose that connects the oil cap mounted PCV valve and the metal hard line on 1973 Mercury Cougar and Ford Mustang Q-code 351CJ engines only. Used hoses will have faded Motorcraft markings (if present). Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes all 1969-72 351, and 1973 351-2V engines. *Note - These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't...

C9AZ-6A664-A Original used hose that connects the valve cover oil cap mounted PCV valve and the front of the Quadrajet carburetor base plate on 1970 through 1971 Mercury and Ford 429 Cobra Jet engines only. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work)....

D0AZ-6A664-C Original used hose that connects the valve cover mounted PCV valve and the carburetor spacer plate on 1970 Mercury Cougar and Ford Mustang 351 Cleveland engines both 2 and 4 barrel versions."L" shaped hose, 1/2" in diameter, approximately 15-1/4 inches long. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes 1969-70 351W or Windsor engines. *Note - These molded and...

C9OZ-6A664-A Original used hose that connects the original PCV valve to the carburetor spacer plate. All 1969-70 351 Windsor 2V and 1969 351Windsor 4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. This hose is a bit longer than the 289/302 version due to the taller deck height of the 351 Windsor engines. *Note - These molded and contoured hoses were designed to work with the...

C7TZ-6A664-A Used after 02-21-1969. Original used hose that connects the original PCV valve to the carburetor spacer plate. All later 1969 S code 390-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *NOTE* These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally anything other than period original intake...

D0ZZ-6A664-A Original used hose that connects the original threaded PCV valve combination with C7OZ-6A706-A elbow and the carburetor spacer plate. Molded hose with 5/8" valve end and 3/8" spacer plate end. 1970 428CJ and 428SCJ engines, includes Cougar and Mustang only. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes 1967-69 S code 390-4V and 1968-69 428CJ engines. See part...

C7ZZ-6A664-B Original used hose that connects the original threaded PCV valve combination with C7OZ-6A706-A elbow and the 390 PCV transfer tube on the intake manifold. Molded hose with 5/8" valve end and 1/2" tube end. All 1967-68 S code 390GT or 390-4V engines and 1968-69 428CJ and 428SCJ engines, includes Cougar, Mustang, Fairlane, Torino, Ranchero, Cyclone, and Comet. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some...

Used vacuum hose connects the Regulator to intake manifold on 1967-68 Mercury Cougar and Ford Mustang. Red striped hose about 20.34 inches long. Ford number for hoses is C7ZA-9C770-B.

Used vacuum hose connects the Regulator to Servo Valve on 1967-68 Mercury Cougar and Ford Mustang. Yellow striped hose about 14.09 inches long. Ford number for hoses is C7ZZ-9C746-A.

D2PZ-8597-A New Old Stock service replacement. Fits 260/289/302 engines from 1966-69. The water bypass hose goes between the water pump and water neck that attaches to the intake manifold.

Used vacuum hose with inline muffler, connects the Servo Valve to the Regulator on 1969 Mercury Cougar and Ford Mustang with factory Speed Control. Hose about 42.7509 inches long. Ford number for hoses is C9ZZ-9D860-A.

Left side. Bracket to hold the junction of the steel brake line and the rubber brake hose. Mounts to the frame rail. Fits 1967 Mercury Cougar and Ford Mustang with factory installed Kelsey Hayes 4 puck disc brakes only.Ford part number C5ZZ-2082-D.

Right side. Bracket to hold the junction of the steel brake line and the rubber brake hose. Mounts to the frame rail. Fits 1967 Mercury Cougar and Ford Mustang with factory installed Kelsey Hayes 4 puck disc brakes only.Ford part number C5ZZ-2082-C.

[No Description Provided]

Good used original power steering lower hose bracket and retainer with a new reproduction insulator installed in place of the original crusty or missing insulator.This bracket is for cars with the big block routed power steering hoses.

Used connector plug that attaches to the A/C vacuum switch assembly on the 69 - 72 Cougar or Mustang. The six vacuum hoses are molded into the plug, and for those instances when someone has cut a hose, simply use a hose connector.

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. Kit includes used check valve and fittings shown, but does not include headlight switch. "I found a good way to...

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. "I found a good way to remove 50 years of crud. Soak the lines in hot water and dawn dish soap for a bit then take a...

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. If you have a tried and true method of cleaning these hoses let us know and if it sounds good we will post it here!NOTE:...

This is what is referred to as a campaign part. It was found that the early 1967 Cougars were having some issues with the headlights and this revised hose kit with ground strap was the fix. Often these have been found opened on dealers shelves with the "near new" take off hoses placed back in the original box. This is a great find for the guy wanting to do a concours restoration on his 1967 Mercury Cougar. Not for use on a 1968 as the switch was located under the dash as opposed to next to the...