General (Old Category Structure)

Correct for all 1967 Cougars with a 289. Keep in mind the Cougar never came factory with a 289 HiPo.

C8AZ-9A603-C metal shroud and tube assembly that attaches to the factory 1968 air cleaner assembly on all C code 289-2V engines as well as F code 302-2V, and J code 302-4V engines all for 1968. We do not believe that this set up came with the Canadian export Cougars, those 1968 Cougars should have the closed PCV system, much like the 1967 49 state Cougars.Do to age and their location our used risers will have minor surface rust, but otherwise be in good condition. Reproduction version of this...

C8AZ-9A603-C metal shroud and tube assembly that attaches to the factory 1968 air cleaner assembly on all C code 289-2V engines as well as F code 302-2V, and J code 302-4V engines all for 1968. We do not believe that this set up came with the Canadian export Cougars, those 1968 Cougars should have the closed PCV system, much like the 1967 49 state Cougars.Do to age and their location our used risers will have rust and or be very thin in spots. Reproduction version of this part is no longer...

Grade B exhaust manifold heat shield for any 1970 Mercury Cougar or Ford Mustang with 351C engine, 2V or 4V, it doesn't matter. Uses a separate, small diameter metal tube (part number D0OZ-9652-A) that attaches to the 1970 Cleveland air cleaner snorkel. Grade B used will have minor pitting, and may have small holes and or rough rusted edges. When mounted it would be difficult to see the defects. We also stock A grade versions.Replaces Ford part number D0OZ-9A603-F.

Since we have a difficult time keeping grade "A" Windsor heat shields in stock we also offer a driver quality version. This unit will be very thin from rust in certain areas. C9OZ-9A603-A Metal shroud and tube assembly that attaches to the factory 1968-1969 air cleaner assembly on all 351 Windsor engines both H code 351-2V and M code 351W-4V (1969 offering only). *Note - for 1970 this shield is used after build date of 2-2-1970, but could be used on prior dates. We suspect that the early 2...

D0AZ-9A603-C This is a two piece metal shroud unique to early production 1970 H code 351-2V Windsor Cougars. Due to problems Ford had with this design they returned to the 1969 style later in the year (after 2-2-70). *Note - 1970 351-2V Windsor cars build before 2-2-1970 used a two piece heat shield. Also used air cleaner snorkel D0OZ-9A626-B and a paper 'S' tube. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts....

Very hard to find, one year only part that is not currently reproduced. These came on 1968 Cougars equipped with the "S" code 390 and the "X" code 390. Must have for that show quality GT or XR7-G. *NOTE* Please keep in mind that our hard to find parts like this are not always competitively priced with what you will find on the open market at swap meets and private party sales. Our primary intent in listing these is for our customers to use this website as a resource to properly identify parts...

*NOTE: This item comes un-painted from the manufacturer.Another spot on reproduction! Correct for CJ and SCJ.  Comes with brackets and hardware as shown. Click on images to enlarge. ...

Sold individually Zinc (Dark Silver)

Used heater and air conditioning box for early to mid 1967 Mercury Cougar and Ford Mustangs. These are getting so hard to find without a broken drain cock or rust in the metal lips. We have a few single halves if you need the half without the drain cock. Soon we will have every single internal and external part from this assembly listed here, in the mean time give us a ring for those obscure parts! The unit you see pictured is typical of what you can expect in a 1967-68 with just a minor...

Reproduction heater blower motor for Mercury Cougar and Ford Mustang. Wiring will need to be spliced into your existing wiring harness. Save the squirrel cage and the heater motor mounting plate from your old unit because it is not included with this item.These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units....

Reproduction heater blower switch that mounts to the rear of the factory installed A/C ventilation control panel on  Mercury Cougars and Ford Mustangs.Replaces part # C8ZZ-19986-A.

This reproduction heater blower switch for Mercury Cougar and Ford Mustang mounts to the rear of the factory installed air conditioning ventilation control panel.Replaces part # C7ZZ-19986-A.

These are getting so hard to find without a broken drain cock or rust in the metal lips. The unit pictured here is typical of what you can expect when you buy out used complete box. Plan on repairing the drain cock or other minor cracks. All doors will be functional, we will not promise the evaporator is good and we do promise the heater core will be bad. We have a few single halves if you need the half without the drain cock. Soon we will have every single internal and external part from this...

Usually ships in 3-5 business days. Reproduction heater box with A/C for 67 - 68 Cougars and Mustangs. This new plenum is made of a sturdy hard plastic that should hold up much better than the original fiberglass boxes. Includes pre-installed seals, clips, flaps, brackets, etc. Just install your heater core (with end cap seals) and AC evaporator (with rubber grommet). See related products. The style of this box most resembles the 1967 version, with the flat mating surfaces between the two...

Usually ships in 3-5 business days. Reproduction heater box with A/C for 69 - 70 Cougars and Mustangs. This new plenum is made of a sturdy hard plastic that should hold up much better than the original fiberglass boxes. Includes pre-installed seals, clips, flaps, brackets, etc. Just install your heater core (with end cap seals) and AC evaporator (with rubber grommet). This assembly comes with two heater core gaskets, one for early 69 and one for late 69 - 70. NOTE: We've received some helpful...

Usually ships in 3-5 business days. Reproduction heater box for the Mercury Cougar or Ford Mustang equipped with air conditioning. These are getting so hard to find without a broken drain cock or rust in the metal lips, so we are happy to bring you this quality reproduction! This unit will come with all the necessary seals and clips. If you need to replace them you can get the heater core here or the blower motor here. We suggest reusing your original A/C evaporator as long as it doesn't leak...

Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Due to the age, there may be a minor stress crack or blemish, it will be a good used assembly. Note that this does not come with a fan assembly, so you will need to reuse your old one. Heater core IS NOT INCLUDED. This icon means that we're looking to buy this part!WCCC is a...

Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). The pictures in the sequence above are reference pictures, grade B boxes will have cracks or breaks. Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Save your old fan motor and plate, this unit does not come with a fan assembly. Grade B used, will have a crack or chips in the fiberglass. Fair condition, will need a...

Heater Box Assembly for 1967-1968 Mustangs without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a factory type fiberglass two piece heater box/heater core casing. The heater box is a pre-assembled unit which includes the gasket and all seals. The heater plenum attaches to this assembly and directs warm air to the car. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts...

Basic clam shell box as shown for cars WITHOUT AC. Keep in mind we have nice original FoMoCo units for less money! *NOTE*Kit does not contain heater blower motor, squirrel cage, or blower motor mounting plate. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years. ...

Used Heater Box Assembly for 1967-1968 Mercury Cougar and 1965-68 Ford Mustang without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a used factory fiberglass two piece heater box/heater core casing. We suggest purchasing the foam kit and new heater core. These used boxes are over 45 years old, there will likely be some cosmetic issues, which include minor cracks or chipped fiberglass. Clips to hold two pieces together are included. *Note...

Special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws. ...

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. This taller or round clip is slightly easier to clip onto the boxes. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard...

Set of 4 special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Reproduction heater cable for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit is an exact fit!Replaces part # C7ZZ-19988-A.

Reproduction heater cable for Mercury Cougars and Ford Mustangs equipped with factory A/C. Replaces part # C9ZZ-185188-A.

We offer this "Core Grade" assembly for those that purchase the various 1968 reproduction bezels. This assembly will provide the needed 'guts' for the various 1968 Mercury Cougar heater control bezels. A Complete heater control assembly includes bezel or face plate, bracket control mounting plate, electrical switch, and hardware. Ford part # C8WA-18531.*NOTE* - Does not include knobs or cable.

Complete used heater control assembly that includes a bezel / face plate, bracket control mounting plate, electrical switches, and vacuum switches. Functional, driver quality, heater control assembly. Knobs and light socket wiring harness not included. Replaces part # D1ZZ-18A651-A. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A silver paint pen (purchased from most artist...

C9ZZ-18A651-A Complete heater control assembly includes bezel or face plate, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. Expect some degree of wear and tear on the plastic knobs and the lever borders. Knobs and light socket wiring harness not included. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A...

Heater control bezel for Mercury Cougars without A/C. Assembly includes bezel in A grade condition. You will most likely have to paint to match your dash color. Check back often, this type and grade of part is seldom in stock very long. Will likely have a couple of pits in the chrome plating. Almost never as nice as the one in the photo. Ford part # C7WA-18531-A.

This reproduction knob set is made by Scott Drake Enterprises. Unlike original knobs, these have a much larger font. Much easier to read while driving than the originals. Replaces Ford Part #: C8ZZ-18519

Used heater control light and socket assembly. Good for 71 - 73 Cougars with or without A/C.

Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...

Constructed from corrosion resistant copper and brass. A great buy for anyone needing to make repairs to this vital part. Replaces Ford Part #: C5DZ-18476-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with AC, but many of the same concepts apply to other years. ...

These reproduction pieces are factory correct replacements for your 1967-68 Cougar or Mustang and will only fit non A/C heater cores of those years.

Our heater cores are the finest available anywhere for any price and they are constructed from corrosion resistant copper and brass. A great buy for anyone who is sick of smelling anti-freeze and needing to make repairs to this vital part. Replaces Ford Part #: C9ZZ-18476-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years. ...

Our heater cores are the finest available anywhere for any price. Constructed from corrosion resistant copper and brass. A great buy for anyone who is sick of smelling anti-freeze and needing to make repairs to this vital part.Replaces Ford Part #: D1ZZ-18476-B. Check out our video below on how to replace a heater core! We used a '69 Cougar with AC, but many of the same concepts apply to other years. ...

Concours correct red striped heater hose for Mercury Cougars and Ford Mustangs built prior to 2/1/1970. After 2/1/1970, the stripe on the hose was changed to yellow. This hose features durable red striping with "Autolite" spelled out and is dated H9H04B. Correct for all V-8 engines WITHOUT air conditioning. The hoses for cars with A/C have 90 degree elbows molded at one end which fits on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so...

Concours correct yellow striped heater hose for Mercury Cougars and Ford Mustangs produced after 2/1/1970. A red stripe was used before 2/1/1970. Durable yellow striping with "Autolite" spelled out and dated H0A13A. Correct for all V-8 engines WITHOUT air conditioning. Hoses for cars with A/C have a 90 degree elbow molded into one end that goes on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so that the yellow striping shows! ...

Concours correct heater hose for all Cougars and Mustangs built after 2/1/1970. Prior to that year, red striping was used. These hoses feature durable yellow striping, "Autolite" spelled out, and are dated LQ0H04A. Correct for all V-8 engines WITHOUT air conditioning. The hoses that are used on cars with A/C have a molded 90 degree elbow at the end that fits on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so that the yellow striping...

Concours correct yellow striped heater hose that features durable yellow striping with "Motorcraft" spelled out and dated LQ1H04A. Correct for all V-8 engines WITHOUT air conditioning. The hoses for cars with A/C have a molded 90 degree elbow at the end that fits on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so that the yellow striping shows!Replaces part # D2ZZ-18472-Y

Concours correct red striped heater hose for late 1968 (after 2/1/1968) Mercury Cougar and Ford Mustang. Durable red striping with "Autolite" spelled out and dated H8A23B. Correct for all V-8 engines without air conditioning. The difference with the 'with air conditioning' hoses is they have a molded 90 degree elbow. Some length trimming may be needed for a tight looking fit. Turn those hoses so that the red striping shows!

Concours correct red striped heater hose for 1969 Mercury Cougars and Ford Mustangs with factory or integral air conditioning. Durable red striping with "Autolite" spelled out and dated H8H02A. These hoses have a correctly molded 90 degree elbow on one end that fits on the water valve side. Some length trimming may be required for a tight looking fit.

Concours correct red striped heater hose for all 1969 Mercury Cougars and Ford Mustangs WITHOUT air conditioning. Correct for use with all V-8 engines. Durable red striping with "Autolite" spelled out and dated H8H02A. Some length trimming may be required for a tight looking fit.

Concours correct red striped heater hose for Mercury Cougars and Ford Mustangs built prior to 2/1/1970 WITH factory or integral air conditioning. After 2/1/1970, the red stripe and date code was changed to yellow. Durable red striping with "Autolite" spelled out and dated H0A12A. Correct for all V-8 engines with A/C. Theses hoses have a correctly molded 90 degree elbow on one end that attaches on the water valve side. Some length trimming may be required for a tight looking fit. Turn those...

Concours correct yellow striped heater hose for Mercury Cougars and Ford Mustangs produced after 2/1/1970 WITH factory or integral air conditioning. Before 2/1/1970 a red stripe was used. Durable yellow striping with Autolite spelled out and dated HOA13A. Correct for all V-8 engines with A/C. These hoses have the correctly molded 90 degree elbow that goes on the water valve side. Some length trimming may be needed for a tight looking fit. Turn those hoses so that the yellow striping shows! ...