Contact Us / Visit Us (click here)
If the Shopping Cart takes too long to respond, you can bypass the shopping cart and go straight to the checkout page by clicking the following link: Checkout.
International Customers Click Here [Updated 1/2024]
Loading Trivia . . .

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 1825-1872 of 13243
Price: $27.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25133 -

D0WY-13B013-A Center section that connects to the vacuum motor on 1970 Mercury Cougar, including XR7 and Eliminator. The center piece is offset to the left of center and the hook part that goes to the vacuum motor points down.1969 and 1970 center shafts are not interchangeable.

Centering Ring - Steering Column - Fixed / Tilt - Repro ~ 1968 Mercury Cougar / 1968 Ford Mustang
1968 Ford Galaxie and LTD,
1968 Ford Fairlane and Torino,
1968 Mercury Comet and Montego,
1968 Ford Falcon,
1968 Mercury Meteor
0
Price: $45.55

Buy Details

Availability: In-Stock Item
Item #: 31655 -

Reproduction upper tube lower insulator for the 1968 Cougar or Mustang column. Used to stabilize the lower end of the steering column. Works on both tilt and fixed columns. Outside diameter is 2-1/8" inches and inside diameter is 1-1/2" inches. NOTE* Ford describes this as an "upper" bearing in relation to the lower steering column tube bearing. It is not used at the upper end of the column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a...

Price: $39.87

Buy Details

Availability: Out of Stock
Item #: 15-0199 -

Used centering ring for any fixed or tilt column on a 1968 Cougar or Mustang.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Price: $39.87

Buy Details

Availability: In-Stock Item
Item #: 15-0198 -

Used centering ring for any fixed or tilt column on a 1969 - 1973 Cougar or Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Price: $58.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0131 -

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator, lever, switch, and hardware sold separately. Unbroken condition, it will definitely need new foam on the door. Stapled foam seal to center vent may not be perfect.Replaces Ford part number C7ZA-19740-B.

Price: $38.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0132 -

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator, lever, and hardware sold separately. Unbroken condition, it will definitely need new foam on the door.Replaces Ford part number C9ZZ-18471-A.

Price: $48.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0133 -

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator and hardware sold separately. Unbroken condition, it will definitely need new foam on the door.Replaces Ford part number D1ZZ-18471-A.

Price: $115.00

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 26751 -

Channel bracket cut from a car. This is the front bracket for mounting fuel tank straps on a 1971-73 Mercury Cougar. Mustang may be the same, just not sure. No Ford part number found. We cut it from a car, spot welds of the actual bracket will need to be drilled and cleaned up prior to installation. Make sure that you measure the exact location of this bracket before you remove from your car. 

Price: $20.57

Buy Details

Availability: In-Stock Item
Item #: 13700 -

This manual with it's 101 pages will undoubtedly save you many hours of frustration.Here's our video on chassis and suspension upgrades:

Price: $18.25

Buy Details

Availability: In-Stock Item
Item #: 25880 -

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar.Here's our video on chassis and suspension upgrades:

Price: $58.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 16-0045 -

Used transmission line adapter and check valve for all FMX transmissions. This fitting goes into the rear part of the transmission case and connects the rear most cooling line to the case. Has internal ball check valve to prevent fluid from back flowing. All FMX transmissions 1969-73 Mercury Cougar or Ford Mustang. The male threads going into the transmission case are 1/2-20 pipe threads.Replaces Ford part number C3AZ-7D174-A.

MSRP:$51.99
Price: $36.00

Buy Details

Availability: In-Stock Item
Item #: 26096 -

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

Price: $48.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 19023 -

This one in, one out design was unique to the early 1967 Cougar for the headlights. Also found on vacuum controlled options like the 1967 Mustang Cougar tilt / tilt-away steering column. This is a good used unit that has been tested and found to hold vacuum well. This valve is located a few inches behind the carburetor.

Price: $59.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 19220 -

This check valve is located in-line just behind your carburetor. To test it simply place it in your lips and try blowing through the side with the single port. You should be able to breath in and not breath out. If this valve is bad you will find the headlights opening up after the engine has been shut off on your 1969 - 1970 Cougars and your tilt away function not working correctly on your 1967 - 1970 Cougars equipped with a tilt column. A good working vacuum system should be able to...

Price: $8.10

Buy Details

Availability: In-Stock Item
Item #: 11646 -

Midland boosters with power drum or power disc brakes and includes the grommet. The check valve diameter is 0.830" for a 13/16" hole and the hole in the Midland boosters is right at 1.040" in diameter.

Price: $194.85

Buy Details

Availability: Rare / NOS Part
Item #: 33115 -

Screws onto the cylinder head smog tubes. Sold individually, two needed per application. Ford part number C8AZ-9A487-A.New old stock Ford.

Price: $33.89

Buy Details

Availability: Out of Stock
Item #: 31432 -

Screws onto the cylinder head smog tubes. All California emissions 1967 Cougars with 289 or 390 engines, and 1969 - 1970 Boss 302 Eliminators, all thermactor smog air tubes. Sold individually, two needed per application. Due to the difficulty in removing these valves, we sell them attached to the air supply tubes. These are aftermarket replacements and will look significantly different than the OEM factory installed valves. But they work.

Price: $83.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23927 -

Screws onto the cylinder head smog tubes. All California emissions 1967 Cougars with 289 or 390 engines, and 1969 - 1970 Boss 302 Eliminators. Sold individually, two needed per application. Due to the difficulty in removing these valves, we sell them attached to the air supply tubes. See 1967 cylinder head smog tubes.

Price: $110.95

Buy Details

Availability: In-Stock Item
Item #: 30671 -

Reproduction manual choke cable and knob. This one closely resembles the factory manual choke as found on all 1969-70 Mercury Cougar Eliminators with the G code Boss 302 engine and the 1969-70 Ford Boss 302 Mustang. Additionally this style choke was used on all 1970 428 Cobra Jet engines. See the experts for dash mounting locations.

Price: $24.85

Buy Details

Availability: In-Stock Item
Item #: 32356 -

Carburetor choke pull off for most 2V and 4V Autolite or Motorcraft carburetors 1958-74. Diaphragm with a hook on it, to 'pull off' the choke. Ford basic part number is 9J549, part of the dashpot assembly. We do not think that it will fit Holley carburetors. Also fits AMC and Jeep that used Autolite and Motorcraft carburetors. 

Price: $39.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 22234 -

Used cast iron choke stove from any 1970-73 351C-2V Ford engine. This is held on with 4 bolts, and to our knowledge no block off plate is reproduced. Casting number on the iron plate is D0AE-9A705-D, which is only for the plate. The plate and coiled tube assembly has a Ford part number of D0AZ-9C869-B. No hardware included.

Price: $115.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 22235 -

Used cast iron choke stove from any 1970 351C-4V Ford engine. This is held on with 2 bolts. Casting number on the iron plate is D0AE-9A705-C, which is only for the plate. The plate and tube assembly has a Ford part number of D0AZ-9C869-A. No hardware included. Limited to stock on hand.* Note - for those who do not need the choke stove, a cast aluminum block off plate can be purchased through Summit.

Price: $18.25

Buy Details

Availability: In-Stock Item
Item #: 41464 -

Reproduction 8 Cylinder 2V Choke Thermostat Shield for the 1967 and 1968 Mercury Cougar and Ford Mustang

Price: $48.47

Buy Details

Availability: In-Stock Item
Item #: 41553 -

This bezel was never offered from the factory on a Cougar but is a very attractive part for those with a manual transmission and no console. Works with rubber or leather shift boot, three or four speed manual transmission. Check out our video on rebuilding your shifter below: ...

Price: $9.86

Buy Details

Availability: Out of Stock
Item #: 15-0055 -

Two required per car, early 67 used a chrome version of this screw. Later years used this screw.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Price: $22.35

Buy Details

Availability: In-Stock Item
Item #: 10613 -

Very nice reproduction cigar lighter knob for 1970 Mercury Cougar and Ford Mustang. Metal knob, screws onto your heating element.

Price: $18.77

Buy Details

Availability: In-Stock Item
Item #: 26126 -

Knob is exact replacement, element is a generic replacement. Exact replacement for 67-68 dash or 69 center console lighter and lighter socket.

Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 10669 -

Cigar lighter for all 1967-68 Mercury Cougar and Ford Mustang dash ashtray mounted locations. Additionally used on 1969 Cougar and Mustang consoles, console only, not the under dash ashtray unit.

Price: $36.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24360 -

Used cigar / cigarette lighter for the lower dash mounted ashtray unit. 1969 Mercury Cougar and Ford Mustang.

Price: $40.37

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25172 -

Used cigar or cigarette lighter for all 1970 Mercury Cougar and Ford Mustang. Starting in 1970 this lighter moved to the dash position that was vacated by the 1969 ignition switch.

MSRP:$24.00
Price: $20.05

Buy Details

Availability: In-Stock Item
Item #: 41728 -

Knob is exact replacement, element is a generic replacement. Socket and element are manufactured by the same company to insure fit. Exact replacement for 1967-68 dash or 1969-70 under dash lighter and lighter socket. Replaces Ford part # C7ZZ-15052 and C6ZZ-15055-B.*Note - Retainer should have a ground lug on it in order to work with 1969 console cigar or cigarette lighters.

Price: $33.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25408 -

Cigar or cigarette lighter for 1971-73 Mercury Cougar and Ford Mustang. Slight change from the 1970 style, this one has a black plastic shaft. Ford part # D1ZZ-15052-A.

Price: $44.87

Buy Details

Availability: Out of Stock
Item #: 22672 -

Used 20 amp circuit breaker for either 69 - 70 or 71-73 Cougars.Mounted on the Starter solenoid in 69-70 cougars for convertible tops or power windows, and also on 71-73 Standard Cougars for convertible tops, power windows, heated back light, power seats or seat back release.On the 71-73 XR7 the circuit breaker was mounted next to the starter solenoid on a junction block. Different wire diagrams, owner / shop manuals list this circuit breaker in both locations, possibly due to multiple...

Price: $10.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0048 -

25 AMP circuit breaker for all 1968 Mercury Cougars and Ford Mustangs with factory air conditioning. Mounts on the panel, under the dash, next to the fuse block. This particular breaker was also used on the ASC installed 1968 sunroofs. It is 1.07" x 0.40" and has a single green and red dot. Box is marked Tung Sol, 25AMP 12V, and made in the U.S.A. Electrical schematics list this circuit breaker. Ford part # C8ZB-14526-A, C8ZZ-14526-A.

Price: $17.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 27335 -

Used on 1967 Mercury Cougar and Ford Mustang for the air conditioning, located under the dash to the back of the ignition switch. 25 amp circuit breaker, identified in the Ford MPC as part number C5AB-14A065-F or C5AZ-14526-C. It is 1.25" x 0.80". Box is marked FASCO Type 4110. 25AMP 12V. Attached mounting tab is included.These are tested and guaranteed to work.

Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 53193 -

Used in 1968 Mercury Cougars for the sequential motor, located under the dash on a panel next to the fuse block.15amp circuit breaker, not clearly identifiable in the Ford MPC. It is 1.07" x 0.40" and has a single green dot. Box is marked Tung Sol, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's...

Price: $15.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 27333 -

Used in 1967 Mercury Cougars for the stop lamp switch, located under the dash on a panel next to the fuse block.15amp circuit breaker, not clearly identifiable in the Ford MPC. It is 1.07" x 0.40". Box is marked 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. The MPC shows this circuit breaker was also used on 1965-66 Continental convertible and 1965 Thunderbird convertible. These are tested and guaranteed to work.*NOTE* Need help diagnosing a Cougar turn signal...

Circuit Breaker - Stop Light - 15 AMP - Used ~ 1969 - 1970 Mercury Cougar
1970 Mercury Cyclone, 1971 Mercury Cyclone,1969 Mercury Marquis, 1970 Mercury Marquis,1969 and newer Mercury full size
8
Price: $10.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 10172 -

Used in 1969-70 Mercury Cougars for the stop lamps, located under the dash on a panel next to the fuse block.15amp circuit breaker. It is 1.07" x 0.40" and has a single green dot. Box is marked Tung Sol, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. Also fits 1969 and newer Mercury full size, 1970-71 CycloneFord part number C9MY-14526-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the...

Price: $10.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 10173 -

Used in 1971-73 Mercury Cougars and Ford Mustang for the stop lamps, located under the dash on a panel next to the fuse block.15amp circuit breaker. It is 1.25" x 13/16" and has a single green dot. Box is marked FASCO, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. Ford part number D1MY-14526-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

Price: $15.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 27334 -

Used on 1967-68 Mercury Cougar and Lincoln Continental for the tail lamps or running lights in the rear, located in the trunk drivers side upper rear corner. Also used on 1967 Mercury Cougar and Ford Thunderbird for the headlight vacuum solenoids, mounts on panel under the dash board for that application. This 5 amp circuit breaker cycles the rear taillights on and off and is not clearly identifiable in the Ford MPC. It is 1.25" x 0.80". Box is marked FASCO Type 4110. 5AMP 12V. Integrated...

Price: $9.86

Buy Details

Availability: Out of Stock
Item #: 10196 -

These are used hose clamps that bolt to the body and lateral A/C bracket. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available may have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, securing the hoses on most cars. Replaces Ford part number 374125-S100.

Price: $9.75

Buy Details

Availability: In-Stock Item
Item #: 26487 -

Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.

Price: $12.75

Buy Details

Availability: In-Stock Item
Item #: 26490 -

This is the correct battery hold down clamp for the 1971, 1972 or 1973 Mercury Cougar & Ford Mustang. Ford Part #: D0OZ-10718-B. Note: The battery hold down clamp offered by many Mustang / Cougar vendors as "Concours Correct" is actually for the 1974 - 1978 Cougar /  Mustang.

Price: $0.85

Buy Details

Availability: In-Stock Item
Item #: 13911 -

Designed for any one-inch hose, this clamp can be used for a number of different applications including the breather hose between the valve cover and air cleaner on 1967, and 1968 Cougars.

Price: $28.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 10944 -

Band or ring style factory exhaust pipe clamp. For 2 inch outside diameter exhaust pipes. Comes with a course sheet metal type threaded hex head bolt. Ford part number C5DA-5A272-B. *Note all 1967 & 1968 Cougars had 2 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C6AA-5A272-A is the factory style 2-1/4" tailpipe clamp.

Price: $17.75

Buy Details

Availability: In-Stock Item
Item #: 31136 -

Concours reproduction horseshoe clamp with correct style of nuts. Used on all 1967 - 1973 models with 2 inch exhaust tips. Correct for XR7-G, GT-E, Mustang GT, Shelby Mustang, all Ford.   Clamp only, Sold individually. This is a Scott Fuller reproduction.