General (Old Category Structure)

These selector buttons are top quality reproductions with a lot of attention given to the details to make these little units look factory fresh and correct.

Vacuum switch not included. This consists of the two lever assembly for the vacuum and cable actuation of the air conditioning plenums damper doors on your 1968 Mercury Cougar or Ford Mustang with integral A/C.Replaces part # C8ZZ-19B888-A for the switch assembly.

Fits 1967 Cougar and Mustang with factory Heater Only Firewall and 1967 289 engine. Custom Hurricane Heat Cool & Defrost System for 1967-68 Mercury Cougar / Ford Mustang with original 289 V-8 with or w/o Power Steering. Easy to Install! Hurricane Unit mounts to firewall in place of factory heater, a/c & heater fittings pass neatly through original blower motor hole with custom rubber grommet. Electronic switching package includes correct reproduction A/C Control bezel w/ louvers. Electronic...

Reproduction A/C Tag Retainer for the 1967 - 1973 Mercury Cougar

Used vacuum tank or canister for the early built 1967 Mercury Cougar and Ford Mustang with factory or integral air conditioning. According to the Ford Master Parts Catalog, the cutoff date for this A/C canister was December 1967. Later cars used the common two nipple vacuum cans that mount inside the passenger side fender below the hood hinge on the passenger side.Replaces Ford part number C7ZZ-19A566-A.

Grade B A/C vacuum canister that has a non working check valve. Suitable for filling the hole in your passenger side fender apron. This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and not holding vacuum, tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's...

This A/C vacuum canister mounts to the passenger side fender well and controls doors inside the A/C unit. This unit includes a built in check valve. Fits 1968-1970 Mercury Cougar and Ford Mustang. The collapsing or imploding problem has been resolved on this vacuum reservoir with the addition of the ribbing for strength.  Replaces Ford part # C8ZZ-19A566.

Reproduction Air Conditioning Vent Air Door Axle for the 1967 and 1968 Mercury Cougar or Ford Mustang.

Reproduction Air Conditioning Vent Air Door for the 1967 and 1968 Mercury Cougar or Ford Mustang.

Round air conditioning vent registers for all 1967-68 Mercury Cougar and Ford Mustang with factory A/C.

Reproduction factory air conditioning vent register knob. This knob controls the black vent door or valve inside the round registers. These will fit the original axle shafts, but will need to be attached with some super glue or other adhesive. These new knobs fit our reproduction axle shafts that have new splines on them perfectly. Please note the position or orientation of the knob in relation to the position of the internal black plastic butterfly.

Black plastic retainer for attaching the direction air conditioning vent registers.

This new chrome interior A/C vent register kit is spot-on! Comes with driver and passenger A/C vents, knobs and standard center vent with cover plate.

Finally, an answer to the much needed, delicate 1968 air conditioning side vents! Visually, these are very hard to tell apart from the originals we have listed on this site but functionally they are much better in that they are cast in one piece. The originals were very prone to breaking and often when you close the door on your 1968 Mustang, Cougar or Shelby the lower portion of the vent falls off. This kit is correct for the 1968 Mercury Cougar only and it includes all three knobs, right and...

This new chrome interior A/C vent register kit is spot-on! Comes with driver and passenger A/C vents, knobs and XR7 center vent.

Finally, an answer to the much needed, delicate 1968 air conditioning side vents! Visually, these are very hard to tell apart from the originals we have listed on this site but functionally they are much better in that they are cast in one piece. The originals were very prone to breaking and often when you close the door on your 1968 Mustang, Cougar or Shelby the lower portion of the vent falls off. This kit is correct for the 1968 Mercury Cougar only and it includes all three knobs, right and...

Complete vent includes mounting hardware. These are sold individually, so please choose between driver and passenger side. We do not guarantee the felt strip to be in place (see picture for example) and we do not guarantee good chrome finish on the louvers. We do inspect them carefully for cracks. Ford part # C9ZZ-19893-D driver side, C9ZZ-19893-C passenger side. *NOTE* The leading edges of the round plastic register are chromed. Often the chrome will wear off, but if you rotate the register...

This reproduction A/C vent register with knobs is show quality and a perfect fit for your Mercury Cougar or Ford Mustang / Shelby. Includes all three control knobs and dealer pricing available.

Reproduction passenger side A/C vent with black camera case finish for the 67 - 68 Mustang. 

Complete vent includes mounting hardware. These are sold individually, so please choose between passenger and driver side. We do not guarantee the felt strip to be in place (see picture for example) and we do not guarantee good chrome finish on the louvers. We do inspect them carefully for cracks. Ford part # C9ZZ-19893-C passenger side, C9ZZ-19893-D driver side. *NOTE* The leading edges of the round plastic register are chromed. Often the chrome will wear off, but if you rotate the register...

Reproduction driver side A/C vent with black camera case finish for the 67 Mustang.

Reproduction driver side A/C vent with black camera case finish for the 68 Mustang.

This new chrome interior A/C vent register kit is spot-on! Comes with all three knobs and is a direct fit with your existing OEM ducts, switches, and switch linkage parts. Dealer pricing is available.

Finally, an answer to the much needed, delicate 1968 air conditioning side vents! Visually, these are very hard to tell apart from the originals we have listed on this site but functionally they are much better in that they are cast in one piece. The originals were very prone to breaking and often when you close the door on your 1968 Mustang, Cougar or Shelby the lower portion of the vent falls off. This kit is correct for the 1968 Mercury Cougar only and it includes all three knobs and the...

Reproduction pair of A/C vent registers for your 69 - 70 Cougar or Mustang. Sold as a pair. Replaces Ford part numbers: C9ZZ-19893-D driver side, C9ZZ-19893-C passenger side.

part # 370608-S. Used in multiple places on mounting brackets.

This decal was available in both red and purple and both decals have the same Ford part number on them with the purple decal being slightly larger with more defined text. This is the purple version.Decal reads:Ford Dearborn, Mich. Air Conditioner Maximum Operating Charge 4LBS. 8OZ. of R-12 Complies With SAE-J639 Replaces part # D20E-19A688-AB

Available in Red and Purple. Both the red and the purple decals have the same Ford part number on them. The purple is a slightly larger decal, with more defined text. Decal reads: Ford Dearborn, Mich. Air Conditioner Maximum Operating Charge 4LBS. 8OZ. of R-12 Complies With SAE-J639 D20E-19A688-AB

Decal reads: Ford Dearborn, Mich. Air Conditioner Maximum Operating Charge 1LBS. 12OZ. of R-12 Complies With SAE-J639 D1ZA-19A688-AC

This Accelerator Pedal Rod To Firewall Grommet reproduction fits both the 67 and the 68. Replaces Ford part # C6OZ-9793-A.

Reproduction diaphragm pump that mounts on the front all 67 - 73 Cougar or Mustang Autolite 2V carbs as well as 1967 Autolite 4V Carbs. With today's gas, these commonly fail, especially when sitting for extended periods of time. Complete failure will cause fuel leaks, but many times these will affect performance well before a leak actually starts. Good idea to replace every few years or if sitting for 6 months or more. Replaces Ford Part #: C4AZ-9B559-A.

Stainless insert that fits in holes around wheel.Fits the following models with styled steel wheels:1969 Mercury Cougar1970 Mercury CougarThese inserts fit or both the 1969-70 OEM Cougar styled steel wheels and the reproduction 1969-70 styled steel wheels. These are the most up to date version of these bezels. The originals tend to have a more mirrored finish like the stainless steel window trim, these reproductions tend to have a brushed nickel look to them.Sorry, these do not come with...

Set of 20 stainless inserts that fit in holes around wheel.Fits the following models with styled steel wheels: 1969 Mercury Cougar1970 Mercury Cougar These inserts fit or both the 1969-70 OEM Cougar styled steel wheels and the reproduction 1969-70 styled steel wheels. These are the most up to date version of these bezels. The originals tend to have a more mirrored finish like the stainless steel window trim, these reproductions tend to have a brushed nickel look to them.Sorry, these do not...

Polished stainless steel inserts that fit in holes around wheel.Fits the following models with style steel wheels:1969 Mercury Cougar1970 Mercury Cougar1969 Mercury Cyclone1970 Mercury CycloneNice used, in most cases we can supply the rubber gaskets, but not always.Limited to stock on hand. ...

Molded rubber plug, seals access hole in the side of shift housing. Replaces Ford Part # : C5ZZ-7C147-B Check out our video on rebuilding your shifter below: ...

Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...

NOS 1967 Mercury accessories and factory installed optional equipment binder. This catalog was used in the dealerships to upsell customers on a variety of options available for their car. It details options from appearance, comfort and convenience, performance and other miscellaneous items such as fire extinguishers and tire chains.  This is a rare find, dealers were the only ones who were issued these binders, and this one happens to be in great condition.

C9ZZ-14A318-A-Used Wire lead for the accessory terminal found optionally on 1969-70 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire can be marked with C8OB-14A318-A or C9ZB-14A318-A.NOTE: There are two version of this wire, one is long and the other is short. The shorter version has a smaller gauge wire. ...

There are 3 of these acorn nuts used per emblem. They are taller than what was used in 1968.Sold individually.

Ford called this small door latch part an adjuster. It threads onto the bottom of the door latch rod inside the door. Common to most Ford products 1965-1970. Ford part number C5AZ-62218106-A.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service,...

This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many...

Used actuator for the seat back release on the 1971 - 1973 Mercury Cougar or Ford Mustang. This item is tested and will be in working condition. Left is the same as right, two required per car. Sold individually.

This article explains how to switch out the headlight vacuum actuators on the 1967 and 1968 Mercury Cougar in under an hour. Just click "add to cart" and go through checkout, and you'll get a link in your email to download the high resolution version of this article. Do you want to replace those worn out actuators yourself or are you looking for some more great information on your Cat’s headlight vacuum system? The video below is your ticket! ...

Unique for the 1969 351 Windsor engines without air conditioning. Flat steel bar stock spacer that positions the power steering pump a measured distance away from the cylinder head. The bars are 3-3/8" x 3/4" x 1/2" in size. The threaded hole in the center is tapped 3/8-16. The two outer holes for attaching to the cylinder head are 11/33" holes on a 2-9/16 inch center. Verify the pre-tapped holes in your cylinder head if making your own spacer. For 1970, a round spacer was used, as could be...

Unique for the 1969 351 Windsor engines without air conditioning. Flat steel bar stock spacer that positions the power steering pump a measured distance away from the cylinder head. The bars are 3-3/8" x 3/4" x 1/2" in size. The threaded hole in the center is tapped 3/8-16. The two outer holes for attaching to the cylinder head are 11/33" holes on a 2-9/16 inch center. Verify the pre-tapped holes in your cylinder head if making your own spacer. For 1970, a round spacer was used, as could be...

Fits perfect! The collar that slips into the opening of the bell housing is very tight for a precise fit that will withstand high horse power motors.

Reproduction center cap adapter kit for installing Legendary center caps on the Legendary Series GT9 wheels. The spacing is a bit deeper on these specific wheels, so this adapter kit comes with special adapters and longer screws.  This kit is intended to make original and after market Mag 500 and Style Steel wheels center caps work on the Legendary Series GT9 wheels.  Please note that the included screws may not fit the thread pattern of some center caps.  The plates will...