General (Old Category Structure)

Lots of great photos inside and out of the Cyclone, Montego and 1968 Cougar.

Great color brochure showing the full line of Ford products.     ...

This is the jumbo version, a much smaller version is what is commonly found. Mint condition.

This promo guide features all Mercury's from 1968. Notice the Model A in the background. It features a great shot of a red GTE blazing down the track.   ...

Features all the Mercury line-up for 1970. Mint condition, ask us about wholesale pricing or stock trades as we have extras of this promo guide.     ...

Features all the Mercury line-up for 1971.     ...

This guide is mostly for the Mercury Cyclone GT / Spoiler but has a large two page section of a Yellow Eliminator that includes a "bizarre" shot of it showing it going through a huge mud puddle. Great listing of all the high performance, over the counter packages. Did you know you could buy a "Dominator" kit for your Eliminator? Click on images to enlarge.                           ...

Very distinguished looking pair of Mercury Cougar promo glasses. As documented in our "40th Anniversary Introductory Program Book / CD" Mercury came up with dozens of unique ways to promote the new "Cougar" in 1966. For obvious reasons this particular item is amongst the hardest to find, with the Cougar "Hamburger Patties" being the most difficult to find. Cutting is required on these reprints. *Don's sister not included

Nice reproduction of the prop rod used on the 1970 Eliminator. This will work on any 1967 - 1973 Cougar that has had a spoiler installed. The pictures of the installed original prop rod were taken at the 2008 PROWL Cougar show hosted by Cascade Cougar Club. The concours correct BOSS 302 Eliminator pictured is owned by John Benoit in Edgewood Washington. Click on images to enlarge. The above picture shows the approximate location of where to drill the hole in the passenger side rear quarter...

This after market adjustable proportioning valve is far superior to the original equipment. Fully adjustable for tuning front to rear brake bias. Requires some routing modifications of brake lines for proper fit. Includes adapter fittings. Replaces Ford part # C5ZZ-2B091-A, or C7OZ-2B091-B.Fits: 1967 Mercury Cougar 1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang 1968 Ford Mustang 1969 Ford Mustang 1970...

C9OA-2B091-A Cylindrical shaped brass valve, some times called the pressure control valve, brake valve or 'cigar' valve. 1969 disc brake cars have it mounted almost directly on the Pressure Differential Valve on the driver side fender apron. The pressure differential valve is also commonly called the 'brake distribution block'. Please understand that most all of these valves will have some tool marks from pliers or vice grips. It is what we have left after previous owners have serviced them...

Used proportioning valve for the 1967-68 Mercury Cougar or Ford Mustang. This is a cylindrical shaped brass valve, some times called the pressure control valve, brake valve or 'cigar' valve. For 1967 Cougars, this valve is most often found at the junction of the high pressure hose back at the rear end. 1968 had it connected to the distribution block on the driver side firewall. Will come with the C7OE-... stamped valve. Starting in 1969 the valves had a C9OE... Ford part number. These are used...

Reproduction proportioning valve for the Mercury Cougar or Ford Mustang. This is a cylindrical shaped brass valve, some times called the pressure control valve, brake valve or 'cigar' valve. This valve is most often found at the junction of the high pressure hose back at the rear end, or later, found with the distribution block mounted on the driver side apron (inner fender). Replaces Ford part # C7OZ-2B091-B.Here’s a video to help you rebuild the distribution block and proportioning valve: ...

Rubber protection sleeve that attaches to the front bumper brace tubes. 1968 Mercury Cougars only due to the front side marker lights. Attaching point is where the front side marker wiring harness touches the bumper brace. Pliable rubber hose slit as shown, about 1-1/2 inch long for those that want to make their own. Looks like 15/16" ID thin wall rubber tubing. Sold individually, two needed per car.

1969 and 1970 Mercury Cougar rubber sleeve. Attaches to the front bumper brace tubes. Attaching point is where the side marker wiring harness makes contact with the bumper brace. About 2-3/8 inches long for those wanting to replicate from a piece of thin wall 7/8" ID rubber tubing. Sold individually, two needed per car.

This plastic plate / bracket is installed between dimmer switch and the floor of your 67 - 73 Cougar to provide a bit or protection for the wiring.

This plate attaches the 3/8" steel fuel line under the driver's side rear torque box, as it makes its way from the rear frame rail out to the rocker area. It acts both as a mount and as a protector from road debris. These were used on late 1967 to 1968 Cougars and Mustang with the 3/8" fuel line. Early 1967 cars had smaller 5/16" fuel line, and different routing (through the transmission tunnel), and did not use this part. Mounting bolts included.

This plastic protector sleeve is often missing or broken, but occasionally we come across a good used one. This part attaches just in front of / below the fuel tank on the passenger side, and serves two purposes: it routes the wiring closer to the fuel sending unit without it dangling down, and protects it from road debris This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Used cable and knob assembly for opening the driver side fresh air vent on 1971-73 Mercury Cougar without air conditioning. Cable control mounts through the dash in a special dash bezel. About 13 inches in total length.Replaces Ford part number D1WY-6501891-A.*Note - Does not fit Mustang.

"B" grade used cable and knob assembly for opening the passenger side fresh air vent on 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Cable control mounts under the dash below the glove box. Cougar uses a different mounting bracket than the Mustang. B grade will have a broken mounting tab, but will otherwise have a good cable. About 23 inches in total length.Replaces Ford part number D1ZA-6501890-A.

Good used double sheave alternator pulley.Ford Part #: C5AF-10A352-J.

Used cast dual sheave alternator pulley. Casting number C9AF-10A352-C, we believe that these originally had a zinc dichromate finish. Called out for use on various 1969-70 Mercury Cougar and Ford Mustang with a need for a dual sheave alternator pulley.*Note - this is a cast pulley instead of the common stamped steel single sheave version.Ford part # C5AZ-10344-L.

Reproduction alternator pulley, single sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Reproduction alternator pulley, two sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Used stamped steel single groove alternator pulley, typically these are described as being 2-7/8 inches in diameter. We find various casting numbers on them, such as: C5AF-10A352-F1, C5AF-10A352-G1, C5AF-10A352-K, C5AF-10A352-L.Replaces Ford part number C5AZ-10344-K.

Used crank shaft pulley for any 1970 Mercury Cougar or Ford Mustang with Boss 302 engine. This is a double groove pulley with a 5-13/16 inch inner pulley diameter, pulley turns the water pump and alternator. 6-5/8 inches diameter for the smog pump belt. This pulley would have been used without power steering. Also used only up until about Jan, 1970. After Jan 1970, Ford just installed a 3 sheave pulley with the middle sheave not being used. Replaces Ford part number D0ZE-6312-A. ...

C6AZ-6A312-A Two applications on 289 engines. 1. Manual transmissions and standard cooling (standard cooling is the 17 inch radiator). 2. All transmissions with extra cooling (extra cooling is the 20 inch radiator). Dual belt alternator pulley, California emissions permissible. & Without air conditioning or power steering. Ford casting number C6OE-6312-A. Double sheave 67 crank pulley. 6-5/8 inches in diameter.

New crank shaft pulley with 2 sheaves for any 3 bolt, 289 / 302 / 351W engines with power steering and the single belt alternator pulley. Without air conditioning, and without emissions.   6-3/8" overall diameter, has 3/8 and 1/2 inch grooves for fan belts. Replica of the C7AE-6312-A crankshaft pulley by Ford. Double sheave 67 crank pulley.

C5AZ-6312-E Application 289 engines with power steering and the single belt alternator pulley. Without air conditioning, and without emissions.   6 5/16" wide 3" deep to mounts.  Ford casting number C7AE-6312-A. Double sheave 67 crank pulley.

C7AZ-6A312-A. Double or two groove crankshaft pulley. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. 6-1/8 inches in diameter. 1967 Application - Mercury or Ford 289 with automatic transmission and standard cooling (17 inch radiators). Without air conditioning and without power steering. 1968 Application - Mercury or Ford 289 or 302 with or without power steering. Thermactor emissions permissible. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. ...

Has casting number D0OE-6312-B stamped on the inside. Application for 1970 all 351 engines, 1971 M code 351-4V, and 1971 and 1972 H code 351-2V engines with power steering or idler pulley. Dual sheave crankshaft pulley measurement of 8.00" and 6-11/16" diameters. No air conditioning. Ford Master Part number D0OZ-6A312-E. Four bolts hold it on too.

C9OZ-6A312-B. Application 1969 351W engines without air conditioning, and with or without power steering. Ford casting number C9OE-6312-E. Double sheave 69 crank pulley.

Ford part number C8AZ-6A312-C. Application 390-2V and 1968 - 1969 390-4V engines without air conditioning and with power steering. Ford casting number C8AE-6312-C. Double sheave 68 69 crank pulley.

Ford part number C8AZ-6A312-E. Application 1968 - 1969 - 1970 428 Cobra Jet without air conditioning and without power steering. Ford casting number C8AE-6312-E. Double sheave 68 69 70 428 CJ crank pulley.

Ford casting number C1AE-6312-A. Cast iron double sheave pulley. 6-5/8" and 6.00" in diameter. Ford cast number C1AE-6312-A. For use with power steering and air conditioning or with California thermactor emissions, either or, not both.

Ford casting number C5TE-6312-A. Single cast iron pulley for use with California thermactor emissions and low mount dual alternator pulleys. No other options, just the DSO 52 and 53 California engines. Ford Master Part number C5TZ-6A312-A. 6-5/8 inches in diameter. Together with the inner crankshaft balancer pulley, these now paired pulleys drive both the water pump and alternator pulleys. The Thermactor air pump pulley is driven by the 3rd outer water pump pulley sheave - only. Must use the...

Ford part number C5AZ-6312-B. Application for 1967-68 289 and 302 engines without all of the following; air conditioning, power steering, California thermactor smog. The alternator would also have a single sheave pulley. Ford casting number C5AE-6312-A. Single sheave crank shaft pulley. About 6-5/16 inches in diameter.

NOTE* After comparing to the original pulley, we've found that this reproduction is approximately 3/16" shorter in overall height. New crank shaft pulley, single sheave small block Ford 289 / 302 351W engines up to 1969. Single V-belt or fan belt pulley, means for use with only the alternator. Not for use with power steering, air conditioning, or smog pump. Measures just under 6-1/4 inches in diameter. Single sheave crank shaft pulley with 3 bolt holes, excludes engines after 1970....

Single sheave crankshaft pulley. No options, one single fan belt around the crank shaft pulley, water pump pulley, and the alternator. Probably found on Boss 351, and other 351C cars without power steering or air conditioning.Pulley marked D1ZE-6312-AA.

D0OE-6312-A For both Windsor and Cleveland 351 engines starting in 1970. This is a single sheave pulley, meaning without air conditioning and without power steering. One groove with a diameter of 6-11/16 inches in diameter. Ford Master Part number D0OZ-6A312-A. A four bolt hole crankshaft pulley for use with 1970 and upward crank dampeners.

Used crank shaft pulley for any 1969 Mercury Cougar or Ford Mustang with 351w engine. This is a single groove pulley with a 6-1/8 inch diameter, and would have been used without power steering. One belt just for the water pump and alternator. Also fits other cars with 351 Windsor engines without P/S.Replaces Ford part number C9OE-6A312-D.

Application 390 engines with only an alternator and water pump. Ford casting number C8AE-6A312-B. Single sheave 68 crank pulley. 

Ford part number C8OZ-6A6312-B. Application 289 and 302 engines with air conditioning and power steering optional. Ford casting number C8OE-6312-B. Triple sheave 68 crank pulley. While this pulley is identified as the available pulley over the Ford counter for this application, the C5AE-B pulley is what was installed on 1968 Cougars and Mustangs from the factory.

C5AZ-6312-D Application for 1967-68 289 or 302 engines with air conditioning. Power steering and or California Thermactor emissions permissible. Ford casting number C5AE-B. Triple sheave 67 68 crank pulley. Inner diameters are about 6-1/2 inches, outer diameter is 7-5/16 inches.

Ford part number C8OZ-6A312-C. Applications: 1. 1968 289 - 302 engines with Thermactor emissions and manual transmissions, may have power steering or air conditioning. 2. 1969 Boss 302 Eliminators with all applications. Ford casting number C8OE-6312-C. Triple Sheave 68 crank pulley.

D0AE-6312-C For both the Cleveland and Windsor variety. Starting in 1970 Ford tried to standardize many of the engine parts. This is the "with air conditioning" pulley for all 1970 - 1971 351-2V & 351C-4V engines, and all 1972 -1973 351-2V engines. Triple sheave 6-23/32", 8.00", 8-13/32" inch diameters. A four bolt hole crank shaft pulley for use with 1970 and upward crank dampeners. Ford Master Part number D0AZ-6A312-C. *Excludes 1972 and 1973 Q code 351CJ engines. This means all 1972 and...

D0OE-6312-C For both Cleveland and Windsor 351 engines. This is also the "with air conditioning" pulley, but with power steering option. Triple sheave 8.00", 7-55/64", 6-9/16" diameters. A four bolt hole crank shaft pulley for use with 1970 and upward crank dampeners. Ford Master Part number D0OZ-6A312-B. This is a Service Replacement pulley for D0AE-6312-C. *Excludes 1972 Q code 351 Cobra Jet engines. This means all 1972 351C-4V engines.

D2OE-6312-AA Application - Q code 351 Cobra Jets with air conditioning or power steering. Triple sheave pulley, 6-9/16" and 7-13/64" in diameter. Ford Master Parts number D2OZ-6A312-A.