General (Old Category Structure)

Leaf spring front bolts for any 1968 Mercury Cougar or Ford Mustang. AMK F-368, About 4-3/8 inches long. 4 total pieces, 2 bolts, 2 nuts.

Leaf spring front bolts for any 1969-70 Mercury Cougar or Ford Mustang. AMK F-251, About 4-3/8 inches long. 4 total pieces, 2 bolts, 2 nuts.

Leaf spring front bolts for any 1967 Mercury Cougar or Ford Mustang. For some reason the 1967 bolts are a bit longer than later years. AMK F-1065, About 6-1/2 inches long. 6 total pieces, 2 bolts, 2 heavy washers, 2 nuts.

Fits all models.

Complete 22 bolt set for oil pan on the 70 - 73 Cougar or Mustang.  

Pictured is a complete set of 1967 Hex bolts, spacers and washers. We will make sure they are damage free, rust free, and a complete set removed from the same year of Cougar as yours. There were minor and major changes almost every year so you will want to select the right year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! 

Reproduction bolts and washers for the shoulder belts on any 1969-73 Mercury Cougar or Ford Mustang. Includes 2 each of the "D" bolts and chrome thick washers. Quality AMK kit F-3563.

Bolt kit for mounting power steering ram cylinder brackets to the frame rail on any 1967-70 Mercury Cougar or Ford Mustang. Kit includes: two short bolts with lock washers, long horizontal bolt, nut, and reinforcing washer. Quality AMK fastener kit.

Includes 2 hex head Screw & Washer Assembly aka "SEMS" bolts for the throttle cable bracket on the 1970 Cougar or Mustang equipped with the 428 Cobra Jet.

Installation kit for the fastening the new reproduction deck lids to the trunk hinges on the 67 - 70 Mercury Cougar. The reproduction deck lids don't come with the J nuts installed and we've found this set to be a perfect fit.

New bolts and nuts for attaching the engine frame stands to the frame. Fits all 1967-70 Mercury Cougar and Ford Mustang with V8 engines. 4 bolts and 4 nuts. 3/8-16 X 3 1/2 Grade 5 phosphate flange bolts.

Engine mount bolt kit for installing engine or motor mounts to the frame stands. 1967-70 Mercury Cougar or Ford Mustang V-8. Two bolts and two nuts. Quality AMK part F-753.

Engine mount bolt kit for installing engine or motor mounts to the frame stands. 1971-73 Mercury Cougar or Ford Mustang V-8. Two bolts and two nuts. Quality AMK part F-467.

Reproduction bolts and U nuts for mounting the front valances on either a Mercury Cougar or Ford Mustang.

Reproduction Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang.If you're working on both sides of your grille, you will need two kits, one kit will do one half of the grille.

Reproduction Headlamp Housing Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang

Fits Standard and XR7

Here are our reproduction hood latch support brace bolts and U nuts for the Mercury Cougar.

3M brand two part channel bonding adhesive for gluing in the Mercury Cougar or Ford Mustang door side glass and rear quarter glass. This is the best product on the market for re-gluing those troublesome 1969 side windows. We use this product for our own cars here at WCCC and have found an applicator that works great. If you just need an applicator to do just your car, we have a 60 day loaner you can use right here. However, if you are doing multiple cars or other parts, you may want to...

This 31 page pamphlet / booklet / pamphlet is full of items most people do not know a Cougar could ever be decked out with; from TV's to trouble lights. This dealer promotional guide is loaded with options like air horns, spotlights, vacuum cleaners, ski carrier adapters, Oxford roofs, and other obscure parts you never knew you could spend your money on... Click on images to enlarge. ...

These pamphlets were found buried in the back room of a San Jose California Lincoln-Mercury dealership. There was no reason to keep them after the warranty expired so most were discarded long ago. Great for that person who likes original documents. Limited quantity.

New rubber boot for brake push rod to the master cylinder on all drum brake cars. Fits all 1967-72 Mercury Cougar and 1965-73 Ford anything cars, including Mustang.Trivia - Did you know that 100% of all 1973 Mercury Cougars, came from the factory with front power disc brakes?

Reproduction rubber boot for the drag link end of the power steering ram cylinder on most any 1967-70 Ford small and intermediate sized cars. Comes with band style crimp clamp like the originals. Keep in mind that this product is made from material that is thinner and softer than OEM.

Reproduction power steering control valve boot and clamp, for the 1967-70 Mercury Cougar or 1965-70 Ford Mustang. Gold tone clamp, molded rubber boot, and pair of screws. Very accurate reproduction. 

This is the storage bag that the convertible top cover folds into when the top is in the down position. Ford calls this part the "Folding top dust hood container." It is made from common vinyl top material and is always black. It measures 15"x27" and the bottom portion is sometimes, tapered down to 8". The same design was used for many Ford Products of the day including Torino, Montego and others. Current offering does not have a tapered bottom, it is square. Pictures will show both styles...

New reproduction insert for the Hurst shifter boots. This is designed to protect the integrity and lengthen the life of the rubber boot used to protect Hurst shifters with rectangular arms. After a while, your boot can become stressed and even begin to tear apart when the arm is shifted contantly. You must remove the shifter handle to install the support. You may need to trim into the reinforced area to get a good fit. Installs from the under side of the boot. Check out our video on rebuilding...

Holley fuel filter decal, for Holley equipped cars. Including all 1967-68 S code 390-4V, 1968-70 R and Q code 428 Cobra Jets, 1967 GT-E with W code 427-4V, or 1969-70 G code Boss 302 Eliminators. Concours detail item. C7OE-9155-A. 

Reproduction BOSS 302 MT Emission Decal for the 1969 Mercury Cougar / Ford Mustang

Reproduction BOSS 302 Rev Limiter Decal for the 1969 Mercury Cougar or 1969 Ford Mustang 

Reproduction BOSS 302 Rev Limiter Decal for the 1970 Mercury Cougar or 1970 Ford Mustang 

 Reproduction BOSS 302 Valve Cover Decal for the 1969 - 1970 Mercury Cougar or Ford Mustang

Nice used aluminum intake manifold for 351C-4V and Boss 351 engines. This was a Ford over the counter or Ford dealer performance offering. This manifold was cast by Buddy Bar and looks on modified. Ford number D1ZX-9425-DA, this version allows the use of a square bore carburetor, which is unlike the original Boss 351 Autolite 4300D spreadbore design carburetor. Most enthusiasts were converting to Holley carburetors for performance, which would be perfect for this intake manifold. Dual plane. ...

Rear most convertible top bow #4, from a 1969-70 Mercury Cougar or Ford Mustang convertible top assembly. This is the last bow and would have had a tack strip attached. Bow only, slat brackets sold separately. Ford part number C9ZZ-7651278-A.

Rear most convertible top bow #4, from a 1971-73 Mercury Cougar or Ford Mustang convertible top assembly. This is the last bow and would have had a tack strip attached.   Ford part number D1ZZ-7651278-A.

Used to cushion and protect top vinyl from excessive wear from side rails. Unfortunately none of the reproductions that we have found resemble the OEM pads. OEM pads looked canvas on the under side that goes against the convertible top rails, and what looked like the soft side of a velcro strip on the upper side that makes contact with the convertible top itself. These are still highly recommended as they keep the convertible top rails from rubbing thorough the convertible top. "I found WCCC...

Good used Western part that is not bent or heavily rusted and the left is the same as right. This is the round style and the round and the flat 1971-72 fender braces fully interchange.Ford master part # D3WY-16B134-A.

Support brace between the bottom of the steel lower dash panel and the cowl top. Fits 1969-70 Mercury Cougar and Ford Mustang with either air conditioning or without air conditioning. Ford part number C9ZB-6504672-A.

One end attaches to the right of the brake pedal support, and the other to the dash panel. Original Ford part number C9ZB-6504510.

Sold as pair on exchange or outright. Only cores with minimal corrosion can be considered for exchange. Ford part number C7AZ-6204144-A, casting number as seen on the backside reads C8AB-6204122-B.  Does not include smaller rod for the sun visor tips.  Sold as a pair.

Reproduction Sun Visor Bracket & Rod for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang. Great quality and fit, left and right use same part, sold separately. Replaces Ford part # C7AZ-6204144-A.

Used mounting bracket from a 1967-68 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. 

Used mounting bracket from a 1971-73 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. 

Used bracket or mounting tab that often gets lost when servicing the air conditioning plenum. Attaches to the box with two screws and has stud that goes through the engine firewall for mounting the A/C box assembly under the dash. Basically the same part as found on 1967-68 brackets, but this one has a slightly longer stud. Replaces Ford part number C9ZZ-18A456-A.

Used bracket or mounting tab that often gets lost when servicing the air conditioning plenum. Attaches to the box with two screws and has stud that goes through the engine firewall for mounting the A/C box assembly under the dash. Basically the same part as found on 1969-70 brackets, but this one has a slightly shorter and pointed stud. Replaces Ford part number C7ZZ-18A456-A.

1967 Cougar and Mustang tubular steel brace. Connects and supports the rear of the air compressor to the factory intake manifold. From what we can tell there is no difference 67 to 68.Ford part # C7ZZ-2889-A.

289 engines without factory air conditioning.

B1967 California emissions low mount alternator bracket for the S code 390-4V engine. Ford casting number C6AE-10156-A, Ford part number C6AZ-10156-A. The early bracket has two extra (for unknown reasons) small holes. Notice this late bracket can be found with both styles of FoMoCo logos.Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and...

Bracket mounts to 9 inch third member. Will not have heavy corrosion as found on Midwest and Eastern cars. Not notched like later years of snubbers. Correct for 1967 Mercury Cougar and 1965-67 Ford Mustang. Rubber bumper sold separately - C3AZ-4730-B rubber carrier bumper. Picture - 2007 40th Anniversary show in Carlisle PA. Bill Pratt with "Catvert".