General (Old Category Structure)

Grade "B" original metal emblem for your Eliminator or Standard model Cougar. Grade B emblems will have pitting and faded or missing paint. We rarely ever get flawless examples of this particular emblem as the original plating was substandard (in our opinion). This emblem was used on the standard, decor and Eliminator models.

Good used emblem with no bends, but will be scratched. Will need new adhesive tape as these did not come with studs. For any Cougar, but only came on 1969-70 Standard Models, and all 1971-73 Mercury Cougars. 1971-73 XR7 and Standard Models, as well as convertible.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in...

Grade A used, trunk emblems for 1969-70 XR7 models. We will very seldom have this in stock, the alternatives are grade B used or reproduction. Please see related items below. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line workers did not even attempt to get them very well centered. Both...

Due to corrosion caused from the exhaust this used emblem will most likely have poor quality chrome. The emblem shown would be the very rare exception.

Will show at least a small amount of pitting. Casting number as seen on the back reads D0WB-652803-E.

Used driver side (left hand) XR7 door panel emblem for the Mercury Cougar. The emblem shown is not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold individually. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

Used passenger side (right hand) XR7 door panel emblem for the Mercury Cougar. The emblem shown is not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold individually.

Used XR7 door panel emblems for the Mercury Cougar. The emblems shown are not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold as a pair.

Left is the same as right, one year only emblem at the center top of the door panel. Usually will show a small amount of pitting. Casting number as seen on the back reads D0WB-6520802.

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of all of the 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T.Licensed by FORD

This is the aluminum emblem which mounts on the center of all scuff plates. Features raised script surrounded by "Product Of Ford" like original, adhesive backed and protective coating. Sold individually, two required per car. Replaces Ford part # C8ZZ-6513208-T. Technically this is the version found on 1967 cars, the 1968 versions had a larger blue oval 'Ford', and did not have the 'Product of' line.

These fender emblems look much like the 1968 quarter panel emblems but differ in that they have longer studs that fasten via barrel clips as opposed to a speed nut used on the 1968 quater panel emblems. The Ford casting number on the backside is D1WB-16098-AA. For the money, The 1968 repro quarter emblem is a much better buy . ...

These were on the lower rear portion of early 1967 390 GT Cougar fenders. In later 67 and 68 the separate G and T letters were used on the Mercury Cougar. Comes with replacement tubular nuts as shown. Other applications include 1967 Mercury Cyclone GT and 1968 Mustang GT. The GT rectangle badge was used until sometime between 11/22/66 and 1/28/67, after that, the individual letters were used.Ford part number C7GY-16098-BFord Casting number C7GB-16720-B ...

These were on the lower rear portion of early 1967 390 GT Cougar fenders. In later 67 and 68 the separate G and T letters were used on the Mercury Cougar. Comes with replacement tubular nuts as shown. Other applications include 1967 Mercury Cyclone GT and 1968 Mustang GT. The GT rectangle badge was used until sometime between 11/22/66 and 1/28/67, after that, the individual letters were used.Replaces Ford part number C7GY-16098-B ...

These were on the lower rear portion of early 1967 390 GT Cougar fenders. In later 67 and 68 the separate G and T letters were used on the Mercury Cougar. Comes with replacement tubular nuts as shown. Other applications include 1967 Mercury Cyclone GT and 1968 Mustang GT. The GT rectangle badge was used until sometime between 11/22/66 and 1/28/67, after that, the individual letters were used. Ford part number C7GY-16098-B ...

Decent reproduction of the 69-70 Cougar fender extension COUGAR script. This emblem was used for 2 years only and was located on the driver side front fender extension (fender cap). The originals came with speed nuts but these have push on clips from the back which means they are easier to install as no tools are needed. If one looks very close you will see minor differences compared to original examples. If you want to trade in your dull, pit free emblem for store credit we will give $20 for...

Used front fender extension "Cougar" script. The one you receive may not look as good as the one pictured but will be very close in condition, expect one of the four studs on the back to be missing. Ford Engineering number as found on the backside: C9WB-16098-B Ford number C9WB-16098-A. Note that the 1970 version stamped D0WA-16098-A is slightly different, most noticeable on the letter "C".

Used front fender extension "Cougar" script. The one you receive may not look as good as the one pictured but will be very close in condition, expect one of the four studs on the back to be missing. Ford Engineering number as found on the backside:  Ford number D0WB-16098-A. Note that the 1970 version is stamped D0WA-16098-A.

Amazing quality that surpasses any NOS or restored emblem you will ever see. This unique emblem was only used on the front fender extension (driver side) of the 1967 and 1968 Cougar. Replaces Ford part number C7WY-16604-A. Here's some info on the measurements for placement: 1. From the bottom of the Y to the right edge of the deck lid - 1.28"2. From the top of the deck lid moulding to the bottom of the Y - 0.18"3. From the top of the deck lid moulding to the bottom of the M - 0.73" Also, note...

Used Driver Side / Right Side Fender Extension Emblem for the 1967 and 1968 Mercury Cougar

These fuel door Mercury crest emblems have been lovingly restored by a long time Cougar enthusiast. They have been carefully repainted the correct colors and will really liven up the looks of the rear of your 1969 - 1970 Cougar. This crest was used on all models except the 1970 Eliminator. The engineering number on the back is C9WB-65405A92. To remove your emblem we suggest grinding down the studs on the backside. To install the restored emblem you will have to use epoxy glue. Keep in mind you...

New Old Stock "G" and "T" 1967 Mercury Cougar and Ford Mustang individual fender letters. There were two ways that the cars were called out as GT's. Two individual letters and a single box with "GT" inside. These letters were also used on 1970-71 Mercury Cyclone. Both letters sold together. Ford part number C7ZZ-16098-A and C7ZZ-16098-B.

Found on the lower right corner of all 1971 - 1973 Cougars equipped with the XR7 Interior package. Both mounting studs will be in place and it will have a nice overall finish. Ford engineering number as seen on the backside is D1WB-65061A58-AA.

Reproduction center grille emblem background. This decal is only made with the "7", so you will need to remove the "X" and "R" from your existing decal and adhere them to this new one. You can clean those letters up with some extra fine polishing steel wool. The standard grill emblem with a walking cat uses the same stud configuration as XR7 so you can exchange emblems from one to another. ...

Our used center grill emblems will always have some amount of fade in the plexi area and if the backing has not separated from the rest of the emblem it often times will be lose. We have had good luck filling the backside with epoxy glue. The engineering number as seen from the rear is D1WB-8216-BB.Ford part number D1WY-8A223-B ...

These Mustang emblems have the incorrect pin placement for the 1968 Cougar so if you have original GT fenders you will have to drill new holes. Once mounted they look correct. Replaces the C7ZB... individual casting numbers. Licensed by FORD

Good used emblem with no missing studs, cracks or pitting. We rarely have this one in stock.

This is the correct emblem that came in the center of the hood moulding on a 1973 Standard model Mercury Cougar. It would not look out of place on an XR7 but of course would not be correct.Ford part # D3WY-16637-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested...

This is a very nice reproduction of the 1973 XR7 hood or upper grille emblem. Replaces Mercury part # D3WY-16637-B. Simple to install, this emblem attaches using a clear silicone. Click on images to enlarge. Pictures below show this emblem installed on an original 1973 Cougar hood / grille center trim. ...

Used Grade A 3 1/2" XR7 center cap emblem was used on the Mercury Cougar XR7 hubcap / wheel cover. 

Used Grade B 3 1/2" XR7 center cap emblem was used on the Mercury Cougar XR7 hubcap / wheel cover. 

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

NOS quarter script or emblem for any 1971-73 Mercury Cougar.  Ford casting number D1WB-16B114-A. MPC number D1WY-16098-A.

This emblem was located on either side of the quarter panel in 1968 and both front fenders in 1971 - 1973. The studs on the 71-73 were a little longer but this 1968 emblem is an excellent substitute. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very consistent. The plating is very inconsistent on the original Ford emblems. We are very excited to...

Correct anodized aluminum reproduction emblem for 1969-70 quarter panels. These high quality emblems have the black paint applied to the sides just as the originals did. If you want an emblem that better matches your front Cougar script you might want to consider these chrome emblems. You can reference the above pictures for correct dimensions, as taken from one of our cars using an original script emblem. Measurements are from the rear and lower body lines. *NOTE* This item includes the three...

Two required per car, right is the same as left. Good used Cougar emblem with no pits, deep scratches or broken studs.

Used COUGAR Script Quarter Panel Emblem for the 1969 and 1970 Mercury Cougar

Invest the big money elsewhere...Here is a NOS part we do not suggest paying the extra money for. These NOS emblems are not as good as the reproductions that cost less than half. The chrome is far superior, the studs stronger and the way they are assembled is much better on the reproductions. The type of person that buys these is doing a "very" original, concours restoration and will pay the extra money to avoid an "over-restored" appearance. These are sold singly only. Drive side part number...

These reproductions are fantastic quality! We sent NOS originals to Scott Drake to duplicate and they could not have done a better job. They come with the original type barrel clip fasteners and feature die cast frames with correct pin placement. These emblems are correct in every detail. We are really excited about these as it was said that they could never be done at a reasonable price without compromising quality. These are better than the $650-$750 NOS emblems you used to see occasionally...

Invest the big money elsewhere...Here is a NOS part we do not suggest paying the extra money for. These NOS emblems are not as good as the reproductions that cost less than half. The chrome is far superior, the studs stronger and the way they are assembled is much better on the reproductions. The type of person that buys these is doing a "very" original, concours restoration and will pay the extra money to avoid an "over-restored" appearance. These are sold singly only. Passenger side part...

This "Stick On" Cougar rear deck emblem was only used on models without the XR7 package. They are often missing as once the factory double sided tape dries out they are often lost forever. We also have a few very nice used examples in stock.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line...

High quality reproduction adhesive emblem for your deck lid. Measures 6.5" wide by 2.35" tall. It has the correct black paint applied to the sides. If you have a 71-73 Cougar this chrome emblem is a much better match to your other emblems even though it is not technically correct. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think...

Good used center with minor cracking, missing paint or maybe even a broken mounting tab. This was used on all 1969 Cougars with a three spoke wheel except the XR7.

Reproduction walking cat center emblem for the 69 Cougar rim blow steering wheel.

Good used center with no cracks and an average amount of fade most noticeable in the red portion of the emblem. Many of these emblems are broken or missing because people think this is the horn button and if they just push harder the horn will sound!

Reproduction center emblem for the 69 Cougar rim blow steering wheel.

The 1967 XR7 did not have rocker panel mouldings as did the 1968 - 1973 XR7 Cougars. All 1967 XR7 models came equipped with these "Hash" marks fastened to the rear of both rockers, at a rear tilting angle. Both sides received seven ribs, held by two Phillips screws each for a total of fourteen ribs in all. They were painted semi-gloss black in the recessed areas and the screws themselves were black as well. The leading ribs are usually pretty rough looking due to road debris wear, the one...

Reproduction silver walking cat emblem / insert for the 70 Eliminator T shift handle. Often times these little emblems are missing from the shift handle because the adhesive has worn out and the emblem has fallen out and gotten lost. While technically for the 69 - 70 Eliminator, this handle will fit on any 67 - 73 Cougar with the automatic transmission.