General (Old Category Structure)

New replacement J-nut or they are sometimes called U-nuts. These clip into those square holes in the fender aprons for fastening the fenders on 1967-70 Mercury Cougar and Ford Mustangs. These clips are 5/8 inches from the hole center to folded edge. We also see the same clips with 27/32 inch spacing for fender mounting. Numerous other uses, we find this clip on the hidden headlight buckets on 1967-68 Cougar and XR7's.

This unit consists of a metal shield with rubber stapled to the edges mimicking the fender contours. In most cases, these used shields will need to have the stapled rubber shields replaced. A Mustang shield will not fit a Cougar because the fender has a much different contour.Ford part # C7WY-16A574-A.

This unit consists of a metal shield with rubber stapled to the edges mimicking the fender contours. In most cases,  these used shields will need to have the stapled rubber shields replaced. The 1967 and 1968 Mercury Cougar inner fender splash shields were constructed using a metal panel with a rubber material stapled to this metal shield. A Mustang shield will not fit a Cougar because the fender has a much different contour.Ford part # C7WY-16A573-A.*Installation and detailing tip -...

Set of nuts and Ferrules for thermactor smog tubes on any 1967 S code 390, 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original or reproduction smog tubes. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the smog tubes and other hardware.

New replacement gas tank filler cap for all 1967-69 Mercury Cougars and 1970 Cougars without California emissions. This is a vented fuel cap.

These plastic fillers were mounted to the end of the 1970 hood extension and filled the gap between center grille surround (extension) and the side grilles. Very rare to find a 1970 Cougar with both of these intact as the driver side often got broken when someone reached in the recess for the hood release latch. These feature the original Ford part numbers. Sold as a pair. Disappointing quality, brittle plastic. Unfortunately, used examples are very hard to find, and these are the only new...

These used original plastic fillers mount to the hood extension, and filled the gap between center grille surround (extension) and the side grilles. Very rare to find a 1970 Mercury Cougar with both of these intact as the driver side often got broken when someone reached in the recess for the hood release latch. These feature the original Ford part numbers. Sold as a pair only. Original Ford parts, these will seldom be in stock. Typically the ultra rare driver side may have a defect or small...

Tall style filter for C4 transmissions.  Fits all Ford C4 transmissions for any 1966-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. This is designated as the 'tall' filter, introduced in 1965. I guess that Ford installed a deeper pan in 1965? Solid metal construction with filter inside.

Replacement transmission pan filter and pan gasket kit. Gasket for the C4 (W Code) transmission. Replaces Ford Part Number: C5ZZ-7A098

Used service replacement, black plastic filter retainer for the Mercury Cougar, Ford Mustang and other Fords equipped with Midland Booster. It fits between the master cylinder and brake booster on the aluminum master cylinder spacer. The repro and service replacement filter covers are usually black not white.You can find the filter here. ...

This is a great, well fitting reproduction and is also all you need to replace the firewall on your 71 - 73 Cougar or Mustang. This is the entire wall, from passenger side to driver side, cowl to floor pan. Made specific for cars with A/C.

Reproduction, nice thick firewall insulation pad for the Mercury Cougar or Ford Mustang. We actually like this one better than the "premium" version. These are pre-formed for a perfect fit and appearance and greatly reduced engine noise and heat. The A/C and non A/C versions are the same piece and will fit both A/C and non A/C cars.This pad comes with all the rubber clips needed for installation.

Reproduction pair of brass oil cooler fittings for the Mercury Cougar or Ford Mustang that screws into the oil cooler. 1/2" threads go to cooling lines.3/8" threads go into the radiator.

Quality built new automatic transmission flex plate for all 1967-68 Mercury Cougar and Ford Mustang with 289/302 engines and C-4 automatic transmissions. Looks identical to the OEM Ford plates, has new starter ring installed. Has the correct 28oz. weight for vintage 289/302 engines. The 5.0 liter engines used a 50oz. imbalance.

Brand new flex plate for all 1967-69 Mercury Cougar and Ford Mustang with any of the 390 engines. Also includes 1968 Cougar GT-E with 427-4V engines. Comes complete with new starter ring gear installed as shown. Neutral balance, meaning this has zero weights attached. *Note - Will not work on 428CJ engines.

Brand new flex plate for all 1969 - 73 Mercury Cougar and Ford Mustang with 302 / 351W / 351C engines, and C4, C6, or FMX transmissions. Comes complete with new starter ring gear installed as shown.*Note - Fits common torque converter bolt pattern of 11.40 inches. In 1972 there was a unique C6 torque converter with a 9.50 inch bolt pattern. 

C9MB-6543516-B We're not sure if it is for a station wagon or trunk lock. It is the larger size, so we are leaning towards the station wagon.

NOS flip lock cover for full sized Mercurys. We aren't sure if this for the trunk or the station wagon.

Green floor mats for the 67 - 73 Cougar embroidered with the walking cat and Cougar script logos.

Used Grade "A" condition floor mat set for the 67 - 73 Cougar. Front and rear set.Ford part numbers:Two Piece Front - C7WY-6213056Two Piece Rear - C5ZZ-6513106

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

1967 - 1973 Cougar Logo Rubber Floor Mats - Used Dark chocolate brown, correct for Cougars equipped with Saddle, Ginger, or Tobacco interior. Notice this set is the version that is a couple of inches narrower so it will fit well with the addition of convertible inner rockers.

Reproduction passenger side (right hand) floor pan to firewall extension for the 67-68 Cougar.

These correct floor pan patches are for the 1969-70 convertible and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long and 15 1/4" wide. Great for the person doing a "correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

New Old Stock Ford flywheel. 11 inch clutch, 164 tooth ring gear,12-3/8 inch bolt circle for clutch pressure plate. Cast iron with C5AE-A and C7TE-A. New, never installed Ford manual transmission flywheel. Fits 351W, 351C, and 351CJ. Ring fear installed, factory fresh.

Used OEM Ford 428 Cobra Jet manual transmission flywheel. Stamped C8OE-A. Needs a ring gear, has chipped teeth. No visible issues, no discoloration from heat. Ford 428CJ only, not for 428 SUPER COBRA JET engines. This flywheel on a 428CJ is externally balanced. Should have 184 ring gear teeth.Ford part number C8OE-6380-A.

New manufactured flywheel for manual transmissions. Fits all 1967-68 Mercury Cougar and Ford Mustang with 289 engines with 3 or 4 speed manual transmissions. This flywheel has a 157 tooth ring gear. This flywheel will fit many other Ford small block V-8's with the 157 tooth gear.*Note - Most 1968 and newer Cougars came with 164 tooth flywheels, and they are not compatible.

These are hand made buckets to turn a regular 1967-68 Cougar front valance into a XR7-G valance and they come with templates and instructions. To get an even better idea how they should be installed, take a look at our used XR7-G valance. ...

Original OEM light found on early cars and later recalled. EXACTLY 100% correct with the right serial numbers in the right places as per the blueprints from Shelby American: * IGM 1642 PN on the bottom right * K11123 N14 cm AUF 5m up the right side * No numbers on left side Marchal made several versions of this light, only this one is the correct one for your Mustang. It has the famous 'cat eyes' internal diffuser. Reproduction lights use a different bulb, lack the diffuser and have the word...

Reproduction driver side (left hand) outer front frame patch for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.

Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) outer frame rail patch for the Mercury Cougar and Ford Mustang. The outer rail has weld nuts installed for proper installation.

Steel freeze plug or expansion plug set for any Ford 351C engine. 1970-74 Mercury Cougar and 1970-73 Ford Mustang. 12 piece set with threaded screw in plugs as shown. 

Steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 17 piece set with threaded screw in plugs as shown. 

Used fresh air vent found in the driver side kick panel of all 1969-70 Mercury Cougar and Ford Mustang with or without air conditioning. Please also see the listing for new gaskets for installation.Replaces Ford part number C9ZZ-6501935-A.

Used fresh air vent found in the passenger side kick panel of all 1971-73 Mercury Cougar and Ford Mustang without air conditioning. These are seldom found damage free, we call them Grade B used. Typically there is a chip in the plastic where it is attached.Replaces Ford part number D1ZZ-6501934-A or D1ZA-65019A12-AG.

Core bench seat for the 1968 Mercury Cougar or Ford Mustang equipped with decor interior. 1968 bench seat without optional headrests, but with seat seat back release latches. The foam will almost always be deteriorating or even missing. All seat cores will be solid frames taken from a Western parts car. Keep in mind 68 and 69 are identical except for how the head rests attach. You can easily add head rests from 69 buckets and bolt them to a 68 pair of buckets or bench if you have all the...

Used core bench seat taken from a Western parts car. Will need new foam and upholstery, but solid and complete with headrests. If you would like to put this in a 68 they are in fact identical once the 1969 single post headrests are removed. Does not include seat tracks.

These are our average used, or Grade B, front license plate mounting bracket that attaches to the passenger side of the bumper of all 1971-72 Mercury Cougars. It may or may not have the rubber anti rattle bumpers present, but will have either original or reproduction plastic inserts for screwing on the license plate. This B grade bracket will function properly, but will have some slight damage or signs of straightening.Replaces Ford part number D1WY-17A385-A.

Straight, clean original bumper.Keep in mind we are always looking for Texaco gas station memorabilia for trades! At this point we are mostly looking for poor condition signs. Will consider good condition signs but are really after the "right" patina. ...

Used front console support bracket. Held in place by 2 phillips screws at the front, under the console. NOTE: There were two versions of this bracket, a shorter version without holes and a longer version with holes. See reference photo above.

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to be removed before installation. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2)...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to be removed before installation. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2)...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here.All front end kit parts are identical for both power and manual steering.Note: Bright orange protective covers are to be removed before...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2) Outer Tie Rods, (2) Inner Tie Rods, (1) Idler Arm, (2) Spring Perches. If you...

Reproduction Front end rebuild kit specifically for the 1967 Cougar with articulated strut rod arms. There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to be removed before installation. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2)...