General (Old Category Structure)

New sealed bearing for installing on your 1968-73 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing also came in all of the "service replacement" idler pulley assemblies and is physically larger than the idler bearing for the 1968-69 only idler pulley (68-69 bearing sku: 10827). The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 9/16". On the smaller bearing pulley, this measurement is 1 3/8". Both versions of this...

New sealed bearing for installing on your 1968-69 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing is physically smaller than the bearing used on the 1968-73 idler pulley (1968-73 bearing sku: 10462). The 1968-73 idler pulley assembly came as a "service replacement" on 1968-69 cars. The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 3/8". On the larger bearing pulley, this measurement is 1 9/16". Both versions of...

NOS New Old Stock air conditioning fixed idler pulley for all 1967 Mercury Cougar and Ford and Mustang, all with 390 engines. Ford part number C7SZ-8678-B.

NOS, new old stock bracket and pulley assembly with new installed bearing for 1968-69 Cougar or Mustang equipped with the 390 or 428CJ engine. We also offer a bearing replacement service to rebuild your fixed idler pulley, see item 27539. Ford part # C8AZ-8678-B. ...

Air conditioning fixed idler pulley for Ford or Mercury with the 289 engines. 1965, 1966, early 1967 Ford and Mercury full and midsized cars all with 289 engines and factory air conditioning. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C5AZ-8678-D. ...

Used bracket and pulley assembly for Cougars and Mustangs with the 289 or 302 engine built after 3/1/1968. All pulleys are sold with new bearings installed.  If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! We also offer a bearing replacement service to rebuild your 289 or 302 fixed idler pulley, see item 27539. Replaces part # C7AZ-8678-C. ...

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 289, 302, or 1969 351W engine. We also offer a bearing replacement service to rebuild your 289, 302, or 1969 351W fixed idler pulley, see item 27539.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which were used starting in...

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 351W or 351C engines. Sometimes has Ford number D0AA-8A617-A stamped on the bracket, not always.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which were used starting in 1968, now have an ever so slight amount of play....

Air conditioning fixed idler pulley for Ford or Mercury with the 352 / 390 / 410 / 428 engines. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C5AA-8A919-C and C5AZ-8678-C ...

Used bracket and pulley assembly for 1967 Cougar or Mustang with 390 engines. All pulleys with bearings are sold in working used condition. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got the parts you need! Ford part # C7SZ-8678-B. ...

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 428CJ engine. This is also a service replacement part for the C8AZ-8678-B fixed idler pulley. The only difference between them is that this part has the larger bearing.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which...

Nice lower quality ignition coil for those of you on a tighter budget. A wee bit cheaper than the other performance coils we offer like the Yellow Top Coil or the Pertronix Flamethrower series coils, but still a great buy and very reliable.   

These replacement "Yellowtop" ignition coils are copies of the original. Nice reproduction cosmetically and functionally. This is a very prominent piece and a must have when trying to detail your engine compartment properly. Replaces Ford part # B6A-12029-B.   Note, no decals are included. Check the website in related items.

This linkage fits between the gear at the bottom of the key lock and rod that goes to the ignition switch on the tilt column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Ignition cylinder for the cars manufactured after 5/17/1973. Ignition lock set is new original from the O.E.M. source. Factory fresh with two keys. Fits many ford makes and models manufactured in 73 - 76. Replaces Ford Part #: D4AZ-11582-A.

NOS new old stock ignition lock cylinder for any 1967-69 Mercury Cougar or Ford Mustang.  Ford Motorcraft part # C9AZ-11582-A Here is a helpful "How To" youtube video on how to replace your ignition switch.

Made by the original supplier! Replaces Ford part # C9AZ-11582-A Here is a helpful "How To" youtube video on how to replace your ignition switch.

Ignition lock set is new original from the O.E.M. source. Factory fresh with two keys. Fits 1970 through 1973's manufactured before 5/17/1973. Replaces Ford Part #: D0AZ-11572-A, D2AZ-11582-B, SW-1114.

Replaces Ford part #: C9AZ-11584-A.

Reproduction Ignition Lock Cylinder Bezel Spacer for the 1969 Mercury Cougar - 1969 Ford Mustang 

No more damaging your bezel or surrounding area with a screw driver and hammer. WCCC to the rescue!

Reproduction Ignition Lock Sun Visor Instruction Sleeve Decal for the 1970 Mercury Cougar or Ford Mustang 

Reproduction ignition switch. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Follow the instruction in your shop manual for installation and adjustment. Original Ford part number D1AZ-11572-A. Application also for 1971 Lincoln MK III and 1971 Ford Thunderbird. Ford had a service replacement ignition switch with a part number D4DZ-11572-A, that covered all years 1971-74. We have found that...

Reproduction ignition switch for the 1973 Cougar.  This version has a longer pigtail, and has a shield or tube covering the wires. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Original Ford part number was likely D3AZ-11572-A. Application also for 1971 Lincoln MK III and 1971 Ford Thunderbird. Ford had a service replacement ignition switch with a part number...

1971 working, used ignition switch. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Tested and working ignition switch. Follow the instruction in your shop manual for installation and adjustment. Original Ford part number D1AZ-11572-A. Application also for 1971 Lincoln MK III and 1971 Ford Thunderbird. Ford had a service replacement ignition switch with a part number D4DZ-11572-A, that...

1972 working, used ignition switch. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Tested and working ignition switch. Follow the instruction in your shop manual for installation and adjustment. Original Ford part number was either D2AZ-11572-A or D1AZ-11572-B. Application also for 1971 Lincoln MK III and 1971 Ford Thunderbird. Ford had a service replacement ignition switch with a part...

1973 working, used ignition switch. 1973 version has a longer pigtail, and has a shield or tube covering the wires. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Tested and working ignition switch. Follow the instruction in your shop manual for installation and adjustment. Original Ford part number was likely D3AZ-11572-A. Application also for 1971 Lincoln MK III and 1971 Ford...

NOS ignition switch. 1973 version has a longer pigtail, and has a shield or tube covering the wires. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Tested and working ignition switch. New Old Stock still has the white plastic pin installed, needs to be removed prior to installation. The pin prevents the plunger from moving around in storage. Ford part number D3AZ-11572-A. ...

Here is a helpful "How To" youtube video on how to replace your ignition switch.

Here is a helpful "How To" youtube video on how to replace your ignition switch.

Used ignition switch with a resistor wire for the under dash harness of the Mercury Cougar. This unit has a resistor wire that goes through the firewall.

Used ignition switch for the 67 Cougar or Mustang. Does not include cylinder or keys. Here is a helpful "How To" youtube video on how to replace your ignition switch.

Used ignition switch for the 68 - 69 Cougar or Mustang. Does not include cylinder or keys.Here is a helpful "How To" youtube video on how to replace your ignition switch.

Exact Reproduction of the Ford Illustrated Facts and Features Manual for the 1967 Mercury Cougar which includes facts, specs, some door codes, and much more!

C8OZ-3C511-C Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 Cougar or Mustang with 289 or 302 engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

C9OZ-3C511-A Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1969 Cougar or Mustang with any 302 / 351 engine. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

3C511-351-71 Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1971-72 Cougar or Mustang with any 351 engine. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

3C511-351-73 Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1973 Cougar or Mustang with any 351 engine. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

Replaces Ford Part # : C8OZ-3C511-B

C7AZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1967 Cougar or Mustang with any V8 engine. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

Used metal indicator lens bezel for the Mercury Cougar. This is for late 1967 through 1968 which uses the small housing. The early 1967 lens was taped to the back of the dash pad. Be aware that there are 2 sizes. This bezel is for the brake, belt and turn indicators. It also is for the high beam on the 1967 which used the small indicator. On the 1968 Cougars, they had the large high beam indicator.

Used indicator lenses for the 1969 Standard fuel gauge. Taken from a used gauge, they will be in the best shape possible, no serious wear, no breaks and no cracks. Lettering will be legible and intact. Diffusers are also available.

Used indicator lenses for the 1970 Standard fuel gauge. Taken from a used gauge, they will be in the best shape possible, no serious wear, no breaks and no cracks. Lettering will be legible and intact. Diffusers are also available.

Used indicator lenses for the 1970 Standard temp gauge. Taken from a used gauge, they will be in the best shape possible, no serious wear, no breaks and no cracks. Lettering will be legible and intact. Diffusers are also available.

Used tested red lamp for the rear defog or heated back lite option for all 1971-73 Mercury Cougar and Ford Mustang with that factory option. These are tested, and the lights do work, there is a bulb sealed inside. According to the Ford MPC, this also was used on full sized Ford and Mercury cars.

Used inner and outer driver side (left hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion.Used inner and outer driver side (left hand) wheel house as cut...

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...