General (Old Category Structure)

Used grade "A" horn center / pad in red for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock so obtaining the color you desire would be a rare treat, but we will try our best to accommodate you. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can paint it to match your interior. The reproduction center emblem and outer ring...

Used grade "A" horn center / pad in saddle for the Mercury cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can paint it to match your interior. The reproduction center emblem and outer ring can also be purchased separately. *Restoration Tip*...

Used on two spoke steering wheels. Replaces Ford Part # C0DZ-13807-A. Although it does not "look" right it will function correctly. Those in the know will purchase our good used spring.

NOTE: A FEW CUSTOMERS HAVE MENTIONED THAT THE INSTRUCTIONS MAY BE WRONG. SWITCHING PINS 1 AND 5 HAD A BETTER RESULT. IF YOU RECEIVE THIS PART AND ARE HAVING TROUBLE WITH THE INCLUDED INSTRUCTIONS, TRY SWITCHING TO SEE IF YOU GET THE SAME RESULTS. Make those horns sound like they should! These relay kits work just like my headlight relay kits to deliver full system voltage to your horns. Ford used horn relays on many vehicles into the early seventies. Unfortunately Mustangs after '65 and...

Good used part with no pitting or scratches. Correct for all 1968 steering wheels and 1969 Cougar's equipped with the standard level interior.

Decent used horn ring but unlike our grade "A" used horn ring this one will have very minor pitting but no open blisters in finish. Good value for your driver quality 68-69 Ford / Mercury with two spoke steering wheel.

Reproduction Two Spoke Steering Wheel Horn Ring for the 1968 and 1969 Mercury Cougar. This is a very good reproduction piece. The original horn contact pieces fit nicely. This casting, while different than the 1968 version with the empty cavities is actually stronger. *NOTE* Save your old horn ring, you will need to transfer the rubber spacer and the horn contacts to this reproduction part.*CUSTOMER REVIEW* Called WCCC the other day after calling around to a lot of garages and auto parts...

If you have already begun to install or have installed this item, it is not eligible for return or refund. This rim blow horn switch is made in the United States by Daniel Carpenter Mustang and is made from vinyl like original. When installing, make sure to massage the rim blow switch in place with counter clockwise, compacting strokes. Clockwise strokes (thumb motions) will stretch the switch and when you complete the installation you will find the part has become too long to fit in place...

Tested and working used pair of Hi and Lo tone horns. 1967-68 Mercury Cougar used part number C7WF-13802-B and C7WF-13801-B. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for your show car.NOTE* - Hi tone = passenger side / Low tone = driver side

Tested and working used pair of Hi and Lo tone horns. 1969-70 Mercury Cougar and Ford Mustang used part number C9ZF-13802-C and C9ZF-13801-B. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for your show car.

Tested and working used pair of Hi and Lo tone horns. 1971-73 Mercury Cougar used part number C8DF-13802-A and D0DF-13801-A. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for your show car.

Aluminum flexible tube that connects the vapor canister to the air cleaner. To give this the look of the originals that had a black paper exterior coating you can spray paint it flat black. If anyone knows of a source to buy the original paper coated foil tubes we would like to hear from you. Fits 1970 California Delivered Cars and all 1971 - 1973 Cars. Look for Buck Tag EV or EM. Preheat/Emission Control Duct.3ft long 7/8" O.D. 3/4" I.D. Replaces Ford Part #: D1UZ-9d667-A, D4HZ-9d667-A...

All 1967 289 Cougars with California emissions. Hose that connects from the air inlet assemble to the air pump. Molded hose, thicker in diameter than the other connecting rubber hoses. Inside diameter is about 1 inch. Kind of shaped like a "J". Fits C and A code 289 engines, 1967 Mercury Cougar and 1966-67 Ford Mustang and others. Hose only, no wire spring clamps, included. Ford part number C6OE-9B458-B.

New old stock, special molded California emissions rubber hose. Connects to the anti backfire valve, not sure where the other end attaches. About 12 inches long. Fits 1967 Mercury Cougar and Comet, and Ford Mustang and Fairlane, all with 390 thermactor smog.Ford part number C7OZ-9H534-B.

Reproduction brake booster hose for Mercury Cougar or Ford Mustang. Measures 12" long

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 1/26/70

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/25/67

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/25/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/28/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 12/5/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 2/25/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 2/29/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 6/25/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 6/26/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 8/26/69

Reproduction 14" length economy breather cap hose for the 68 - 70 Cougar or Mustang.

This Gas Tank To Filler Pipe Hose reproduction fits the 67, 68, 69, and 70 Mercury Cougar. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

Both ends have 90 degree molded ends. Attaches heater core to water heater control valve.Replaces Ford Part #: C7ZZ-18472-CVAC.

C8ZA-3494-A Lower pressure hose. High pressure hose from the insulator to the control valve. All correct ribbing, striping, and crimping. Has correct colored protective sheathing. *Note - There are two halves to the pressure hose from the pump to the control valve. This is the lower half only. Please see the various part numbers for the upper section of pressure hose.

New power steering pressure hose for late 1972 and all of 1973 Mercury Cougar and Ford Mustang with 351 engines. This was a re-engineered hose to eliminate that 1971-72 extra long hose that doubles back on itself. Has brass fitting for attaching the pump end steel tube fitting, you need to save that steel tube. Made in the U.S.A. Replaces Ford Part # D1ZZ-3A719-A

NOTE: Some customers have mentioned this hose does not fit well, others have said it fits with no issues. It is not the same as OEM and fitment seems to depend on the vehicle and modifications that have been previously done. We recommend going with our premium version. Lower pressure hose for any 1967-70 Mercury Cougar and Ford Mustang, but with a V-8. The factory power steering pressure hose originally was a two piece hose. Valve end has the 5/16" flared male fitting, and a 3/8" female...

This Pump to Value Outlet Pressure Hose is 100% correct for the 1969 small block, and will work for the 1967 or 1968 with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang /...

This Pump to Value Outlet Pressure Hose is 100% correct for the 1970 small block. This is the upper portion that connects to the one year only 1970 pump found on the 351c, 351w and BOSS 302 equipped cars. Like the originals, this is part one of a two part hose. This hose has industrial high pressure fittings that are much higher quality than those available by most Cougar / Mustang parts dealers. Replaces Ford Part #: D0OZ-3A319-A.

Reproduction hose that connects the oil cap to the air cleaner on cars equipped with the 289 engine. Replaces Ford Part number C6AZ-6A664-P

Reproduction PCV Hose with Ford Logo for the 1969 Mercury Cougar or Ford Mustang with 351 engines. Fits from the PCV valve in the valve covers to the factory Ford carburetor spacer plate.  Approximately 3/8" inside diameter but it will stretch to fit over a 1/2" PCV valve fitting.  Keep in mind that it will stretch easier if warmed.

D3-6A664-2V Original used hose that connects the oil cap mounted PCV valve and the metal hard line on 1973Mercury Cougar and Ford Mustang H-code 351-2V engines only. Used hoses will have faded Motorcraft markings (if present). Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes all 1969-72 351, and 1973 351-4V engines. *Note - These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't...

Concours for 1970 351C-2V and 351C-4V with correct ink stamped Ford script, 17 1/2" long including the 90 degree bend. Connects PCV valve to carburetor spacer plate. Other parts houses list this as a 71-73 but the 71-72 is 25" long (so it can reach to the front of the driver side valve cover) on both the 2V and 4v 351 Cleveland and this hose will not reach. This will work for the 1973 Q-code 351C-4V as the 73 mates to a metal tube and is only 11".This hose was originally installed from the...

C8OZ-6A664-A Original used hose that connects the original PCV valve to the carburetor spacer plate. All 1968 X code 390-2V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - These molded and contoured hoses were designed to work with an original style PCV valve (modern 90° PCV valves won't work). Additionally anything other than period original intake manifolds, valve...

C7TZ-6A664-B Used before 02-21-1969. Original used hose that connects the original PCV valve to the carburetor spacer plate. *Note - These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally anything other than period original intake manifolds, valve covers, and spacer plates can also alter the position and distance in the relationship of the PCV valve and carburetor spacer plate. Click on images to enlarge. ...

C9ZZ-6A664-A Used before 02/21/1969 Original used hose that connects the original threaded PCV valve combination with C7OZ-6A706-A elbow to the carburetor spacer plate. All early 1969 S code 390-4V engines. Molded hose with 5/8" valve end and 1/2" spacer plate end. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - These molded and contoured hoses were designed to work with an original...

NOS ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. Fits 1967-68 Mercury Cougar and 1966-69 Ford Mustang. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers,...

C6AZ-6A664-N Original used hose that connects the original PCV valve to the carburetor spacer plate. All 289-2V, 289-4V, 302-2V, and 302-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. Application for mid year 1966 through 1969 289/302 engines, including Cougar, Mustang, Falcon, Galaxie, Fairlane, Torino, Cyclone, Ranchero, and Comet. *Note - These molded and contoured hoses were...

D1OZ-6A664-B Original used hose that connects the valve cover mounted PCV valve and the carburetor spacer plate on 1971 through 1972 Mercury Cougar and Ford Mustang 351C or Cleveland engines only. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes all 1969-71 351W or Windsor engines, 1970 351C or Cleveland, and 1973 351C engines. *Note - These molded and contoured hoses were...

Concours correct with ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers, and carburetor spacer...

Connects PCV valve to PCV transfer tube on the 390, 427-4V, and 428CJ. Inside diameter on one end is .45" the other end is .58". These should be tough to get on so that they will form a vacuum seal. Originally held on with wire clamps, we have those available here  Replaces Ford Part #: C8AZ-6A664-D. Fits Many 1966, 1967, 1968, 1969, and 1970 Mercury Monterey, Marquis, Ford Galaxie, with FE 390 Big Block Engines. We aren't sure why this hose was reproduced as shown. However it will...

This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Two required per vehicle, sold individually. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper specs. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. Replaces Ford Part #: C6OZ-3A714-A or C6OZ-3A717-A. ...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. One piece design, meaning it differs from the original separate two piece pressure hose set. Upper and lower pressure hoses were what came on the cars originally. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose will work as a return line for either a small or big block 1967 - 1970. This hose is designed for a 2 piece return line application, so to make it work you will need to also purchase a chunk of generic hose. This is needed to connect this hose to your power steering pump.  Depending on the routing of your hoses you will need a different...