General (Old Category Structure)

Quarter window upper stop bracket, fits all 1971-73 Mercury Cougar and 1971-73 Ford Mustang coupe or convertible models. This is the smaller of the two stop brackets, and it installs towards the back of the window. There is a decent illustration of the quarter window installation in the Osborn Body Assembly Manual. One stop bracket per side, right and left are the same.Ford part number D1ZB-6529968-A.

Quarter window lower stop bracket, fits all 1971-73 Mercury Cougar and 1971-73 Ford Mustang coupe or convertible models. This is the longer of the two stop brackets, and it installs near the B pillar of the window. There is a decent illustration of the quarter window installation in the Osborn Body Assembly Manual. One stop bracket per side, right and left are the same.Ford part number D1ZB-6530600-A.

Replaces stop lamp relay on 1967 Cougars built before 1-3-67. No wiring modifications needed, just plug it in in place of your old mechanical relay in the trunk. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the...

New Old Stock relay. Known as the "K-11" relay in the Ford Service manual. This relay was only used in production prior to 1-3-67. It provides a low current circuit through the relay solenoid and the stop lamp switch and a separate circuit through the relay points to handle the higher current load of the stop lamps. Again, this unit was only used in early 1967 Mercury Cougars. This early brake light relay is unique to Cougars built prior to 1-3-67. Unlike the later built Cougars, it...

Known as the "K-11" relay in the Ford Service manual. This relay was only used in production prior to 1-3-67. It provides a low current circuit through the relay solenoid and the stop lamp switch and a separate circuit through the relay points to handle the higher current load of the stop lamps. Again, this unit was only used in early 1967 Mercury Cougars. This early brake light relay is unique to Cougars built prior to 1-3-67. Unlike the later built Cougars, it mounts next to the sequential...

This is the dual port version used on UNITS BUILT PRIOR TO MAY 17, 1967. There was also a single port version in the later part of 1967. These dual port units always leak at the port fitting (easily sealed with epoxy) and the one way check valve never functions properly. Our Western grade A tanks are rust free. Keep in mind we have units that are not as clean looking but still hold vacuum for about half the price. Ford part #C7WY-13A185-C.

This is the dual port version used on UNITS BUILT PRIOR TO MAY 17, 1967. There was also a single port version in the later part of 1967. These dual port units always leak at the port fitting (easily sealed with epoxy) and the one way check valve never functions properly. Our Western grade A tanks are rust free. Keep in mind we have units that are not as clean looking but still hold vacuum for about half the price. Ford part #C7WY-13A185-C.

This single port version was used in the latter part of 1967 and all of 1968. Keep in mind we have units that are not as clean looking but still hold vacuum for about half the price. Cougar part number C7WY-13A185-C headlamp vacuum reservoir.

Good used tank as taken from a Western parts car. Differs from other years only in that the vacuum port is located in a different position. Keep in mind we have units that are not as clean but still hold vacuum for about half the price. Cougar part number D0WY-13A185-A.

Good used tank as taken from a Western parts car. Differs from other years only in that the vacuum port is located in a different position. Keep in mind we have units that are not as clean but still hold vacuum for about half the price. Cougar part number D0WY-13A185-A.

These are the straps that hold the gas tank in place. 2 required, sold individually.Replaces Ford part number D1ZZ-9092.

Used Strap - Large Wire Loop for the 1968 Mercury Cougar or 1968 Ford Mustang

Reproduction Universal Strap / Medium Wire Loom for the 1967 Mercury Cougar or Ford Mustang 

Universal wire loom plastic clip for any application on Cougars or Mustangs, as well as many other models.5" x .26"

These are the straps that hold the gas tank in place. Sold as a pair.Replaces Ford part number D1ZZ-9092.

New strip caulk for the Mercury Cougar or Ford Mustang. These units come in one foot strips and are used for sealing the front fenders to top of aprons and for sealing the fuel tank flange to the trunk floor. They are also used for sealing the floor drain plugs, gas filler necks, door panel water shields, plus many other components that are fastened to the body. This box contains 60 individual strips of black non-hardening caulk.

Reproduction rear deck spoiler stripe in black for the 1970 Mercury Cougar Eliminator. We reproduced these stripes from a NOS kit, and they are the most correct Eliminator stripes on the market today. Cut from the same 3M vinyl as original.Also sold in a complete kit.

Reproduction rear deck spoiler stripe in white for the 1970 Mercury Cougar Eliminator. We reproduced these stripes from a NOS kit, and they are the most correct Eliminator stripes on the market today. Cut from the same 3M vinyl as original.

Reproduction hood stripe kit in black for the hood of the Mercury Cougar equipped with the 351 engine. This vinyl stripe kit features the Cougar Head logo. *NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction hood stripe kit in silver for the hood of the Mercury Cougar equipped with the 351 engine. This vinyl stripe kit features the Cougar Head logo. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction hood stripe kit in black for the hood of the Mercury Cougar equipped with the 428 engine. This vinyl stripe kit features the Cougar Head logo. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Our reproduction 428 CJ hood stripe kit in sliver with the black Cougar Head is made from quality 3M stock and patterned from an original Ford kit. Check out our video below showing how to install this hood stripe. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can...

Our reproduction 428 CJ hood stripe kit with the black Cougar Head is made from quality 3M stock and patterned from an original Ford kit. Check out our video below showing how to install this hood stripe. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find...

Reproduction black hood stripe with silver Cougar head for the 1969 Cougar with the 351 engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction silver hood stripe with black Cougar head for the 1969 Cougar with the 351 engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction white hood stripe with black Cougar head for the 1969 Cougar with the 351 engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction black hood stripe with NO COUGAR HEAD for the 1969 Cougar with the 351W engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction black hood stripe with silver Cougar head for the 1969 Cougar with the 428CJ engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction silver hood stripe with black Cougar head for the 1969 Cougar with the 428CJ engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction white hood stripe with black Cougar head for the 1969 Cougar with the 428CJ engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Nice used driver side strut rod that fits all 1970-73 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1970-71 Torino, Cyclone, Ranchero.. Functionally the same as 1968-69 strut rods, just not stepped down threads at the end. Ford part number C9ZZ-3468-C. Sold as a bare strut rod, we also offer the used hardware for installation here. ...

The Mercury Cougar used this articulated strut rod in 1967 to help give the Cougar a little softer ride over the Mustang. It is debatable just how much the addition of this joint helped. Many people choose to switch these struts for either 1968-69 or 1970-73 strut rods. The main reason is to be able to utilize the reproduction 1968-73 lower control arms, the second reason one would move away from this one year only, cougar only rod is that it is difficult to rebuild. We only sell grade "A",...

The Mercury Cougar used this articulated strut rod in 1967 to help give the Cougar a little softer ride over the Mustang. It is debatable just how much the addition of this joint helped. Many people choose to switch these struts for either 1968-69 or 1970-73 strut rods. The main reason is to be able to utilize the reproduction 1968-73 lower control arms, the second reason one would move away from this one year only, cougar only rod is that it is difficult to rebuild. We only sell grade "A",...

Nice used passenger side strut rod that fits all 1970-73 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1970-71 Torino, Cyclone, Ranchero.. Functionally the same as 1968-69 strut rods, just not stepped down threads at the end. Ford part number C9ZZ-3468-D. Sold as a bare strut rod, we also offer the used hardware for installation here. ...

The Mercury Cougar used this articulated strut rod in 1967 to help give the Cougar a little softer ride over the Mustang. It is debatable just how much the addition of this joint helped. Many people choose to switch these struts for either 1968-69 or 1970-73 strut rods. The main reason is to be able to utilize the reproduction 1968-73 lower control arms, the second reason one would move away from this one year only, cougar only rod is that it is difficult to rebuild. We only sell grade "A",...

The Mercury Cougar used this articulated strut rod in 1967 to help give the Cougar a little softer ride over the Mustang. It is debatable just how much the addition of this joint helped. Many people choose to switch these struts for either 1968-69 or 1970-73 strut rods. The main reason is to be able to utilize the reproduction 1968-73 lower control arms, the second reason one would move away from this one year only, cougar only rod is that it is difficult to rebuild. We only sell grade "A",...

 ‹— 1967 Stock alignment verses reproduction alignment. (Thanks for the pic Peter!)   A nice reproduction. Painted black. Ready to install. Includes correct castle nut. Required to install reproduction front end rebuild kit on a 1967. Replaces Ford Part # C9ZZ-3468-D. We highly encourage you to consider our used rods over these Chinese parts. Our grade "B" rods will take some effort to make look new but in the end it is worth it. The Chinese strut rods are different (but...

A nice reproduction. Painted black. Ready to install. Includes correct castle nut. Includes both the left hand and right hand strut rod arm. These are required to install the reproduction front end rebuild kit on a 1967. Replaces Ford Part #: C9ZZ-3468-C & C9ZZ-3468-D. We highly encourage you to consider our used rods over these Chinese parts. Our grade "B" rods will take some effort to make look new but in the end it is worth it. The Chinese strut rods are different (but similar) from one end...

 ‹— 1967 Stock alignment verses reproduction alignment. (Thanks for the pic Peter!)   A nice reproduction. Painted black. Ready to install. Includes correct castle nut. Required to install reproduction front end rebuild kit on a 1967. Replaces Ford Part #: C9ZZ-3468-C. We highly encourage you to consider our used rods over these Chinese parts. Our grade "B" rods will take some effort to make look new but in the end it is worth it. The Chinese strut rods are different (but...

Reproduction driver side (left hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03487-A.

Reproduction passenger side (right hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03486-A.

Nuts and bolts, associated with the installation of our used 1968-69 strut rods. 1 large and medium nut for the front, and two bolts and nuts to attach to the lower control arm.

Nuts and bolts, associated with the installation of our used 1970-73 strut rods.

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

This listing is for a premium quality pair of 1970 original strut rods in grade "A" used condition. What sets them apart from our grade "B" rods is that after they have been bead blasted they have a smooth finish, no pock marks from rust. This is for the person who is doing a show car and wants the very best, original correct parts that can be found. The reproductions are made in China and work fine but they are different on every detail and do not come with the specialty bolts that attach the...

The Mercury Cougar used this articulated strut rod in 1967 to help give the Cougar a little softer ride over the Mustang. It is debatable just how much the addition of this joint helped. Many people choose to switch these struts for either 1968-69 or 1970-73 strut rods. The main reason is to be able to utilize the reproduction 1968-73 lower control arms, the second reason one would move away from this one year only, cougar only rod is that it is difficult to rebuild. We only sell grade "A",...

This screw / stud seems to always be missing. This stud is just a little longer than stock to allow installing the Hi-Po / 427 GTE air cleaner. Fit most Autolite 4V carburetors assembly. Zinc plated for years of service. Size: 4 1/2 inches 1/4-20 X 1/4-20 threads.