General (Old Category Structure)

Support brace between the cowl top and the brake pedal support bracket. Fits 1969-70 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Ford part number C9ZB-6501554.

Support brace between the cowl and the top of the brake pedal support bracket. Fits 1969 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Overall width is right at 5 inches on the 1969, smaller than the 1970 version. Ford part number C9ZB-65015A18-A.

Support brace between the cowl and the top of the brake pedal support bracket. Fits 1970 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Overall width is right at 5-1/2 inches on the 1970, larger than the 1969 version. Ford part number D0ZB-65015A18-A.

This tubular support gives rigidity to your hood extension which houses your center grille. These are hard to find with no bends or cracks due to the fact that the 1970 hood protrudes in the center.1 required per car.

Used strap or support bracket for the foam air conditioning vent tube going to the driver side A/C vent. The electrical assembly manual indicates that this strap bracket behind the dash on the driver side. Our findings from the wrecking yard show that 1967 is typically rubber coated, 1968 is bare steel. Please specify is you have a preference. The rubber coated ones will show some deterioration, plan on re-dipping or use as-is. Not exactly the same as the support for the passenger side.Ford...

C9ZZ-6501508-B This is the correct hanger for a 1969 Mercury Cougar or Ford Mustang with power disc brakes. If you have a manual transmission car with worn out clutch bushings this is a great replacement part for you as it will have been removed from an automatic transmission equipped car which means the clutch bushings will be in mint, unused condition. Ford master part number C9ZZ-6501508-B for power disc brakes. *Note - Power brake and manual brake supports are different. Power brake...

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes and an automatic transmission. This unit is not for cars produced after 6/25/1972. Ford part # D1ZZ-6501508-C.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with an automatic transmission and manual drum brakes. This unit is for cars produced after 6-25-1972. Ford part # D3ZZ-6501508-C.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with a manual transmission and manual drum brakes. Not to be used in cars produced before 6/25/1972. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and unused condition. Ford part # D3ZZ-6501508-A.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and in unused condition. Ford part # C9ZZ-6501508-A. *NOTE* Manual brake supports are different. Manual brake supports have four threaded nuts swedged to...

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and unused condition. Ford part # D0ZZ-6501508-A. *NOTE* Manual brake supports are different. Manual brake supports have four threaded nuts swedged to the...

Reproduction brake pedal hanger for manual brakes. Can be modified to work for power brakes.

This used brake pedal support bracket is the correct hanger for a 1967-68 Mercury Cougar or Ford Mustang with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint, unused condition. Ford part # C7ZZ-6501508-C. *NOTE* Manual brake supports are different. Manual brake supports have four threaded...

This used brake pedal support bracket or brake pedal hanger is for the Mercury Cougar or Ford Mustang equipped with power disc or drum brakes. We have carefully shown the mounting position of the pedal so you can drill your existing manual brake pedal hanger when converting from manual to power brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means...

D1ZZ-6501508-D This is the correct hanger for a 1971 Mercury Cougar or Ford Mustang and 1972 cars up until 6-25-1972, with power disc front brakes, and with automatic transmissions. Ford master part number D1ZZ-6501508-D for power disc front brakes.

D3ZZ-6501508-D This is the correct hanger for a after 6-25-1972 Mercury Cougar or Ford Mustang and 1973 cars, with power disc front brakes, and with automatic transmissions. Ford master part number D3ZZ-6501508-D for power disc front brakes.

D0ZZ-6501508-B This is the correct hanger for a 1970 Mercury Cougar or Ford Mustang with power disc brakes. If you have a manual transmission car with worn out clutch bushings this is a great replacement part for you as it will have been removed from an automatic transmission equipped car which means the clutch bushings will be in mint, unused condition. Ford master part number D0ZZ-6501508-B for power disc brakes. *Note - Power brake and manual brake supports are different. Power brake...

Reproduction brake pedal hanger also known as the brake pedal support for Mercury Cougar and Ford Mustang.

Reproduction brake pedal hanger also known as brake pedal support for Mercury Cougar and Ford Mustang.

Used front support bracket for the air conditioning compressor assembly. Starting in 1971, Ford eliminated the idler pulley and used this bracket in it's place. Replaces part # D1AZ-2888-B.

Support bracket for attaching headlight assembly to the radiator core support. Right and left are the same, two needed per car. Fits 1971-73 Mercury Cougar.Ford part number D1WY-13B065-A.

Used upper support bracket for the hood latch on any 1969 Mercury Cougar. Ford part number C9WY-16707-A.

Used upper support bracket for the hood latch on any 1970 Mercury Cougar. This 1970 part will work on a 1969. The only difference is the top corner is clipped at an angle on the 1970.Ford part number D0WY-16707-A.

This support bracket mounts to the lowest portion of the quarter window cavity. This bracket is installed before the lower guide bracket. Fits all 1971-73 Mercury Cougar models and 1971-73 Ford Mustang models including fastback or sport roof models. The exploded view of the quarter window parts can be found in the Osborn Body Assembly Manual for 1971-72. One for each quarter window, right and left are the same.Ford part number D1ZZA-6529790-A.

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design. Two different sized brackets used, this is the larger one that is 1-3/4 inches wide. The bracket that goes in the corner above the switch panel is 3/32" less. It was obvious what the original intent was on this design in that a tab on the L bracket was supposed to extend...

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the smaller design. Two different sized brackets used, this is the smaller one that is 1-21/32 inches wide. This bracket goes in the corner above the switch panel. The larger bracket is 1-3/4" or 3/32" wider. It was obvious what the original intent was on this design in that a tab on the L...

This often times missing bracket was attached to the back of your early 1967 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the less common design.It was obvious what the original intent was on this design in that a tab on the L bracket was supposed to extend into the rectangular hole to keep the bracket properly anchored to the fragile plastic. For some reason the majority of the cars built didn't get the better...

Reproduction set of 5 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design of the two and by far the superior. Replaces item # 31908Through 67-68, there were four different style brackets, you can see all four by following this link. ...

This often times missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design.Through 67-68, there were four different style brackets, you can see all four by following this link. ...

Reproduction set of 5 XR7 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. Our improved design is better than the original in that the tab extends into the rectangular recess in the dash bezel which anchors in MUCH more securely. Replaces item # 31907Through 67-68, there were four different style brackets, you can see all four...

Radio support bracket for 1967-68 Mercury Cougar and Ford Mustangs without consoles. Used on AM, AM/FM, and AM/8Track factory radios.Replaces parts #s C7ZA-18888-A & C8ZA-18888-A, as found in the electrical assembly manuals.

Rear radio support bracket for all 1972-73 Mercury Cougar and Ford Mustangs with factory AM/FM stereos. *NOTE*1972-73 Mercury Cougar and Ford Mustang with AM or AM/8 Track radios used the C9AZ-18888-A bracket for installation.Replaces part # D2ZA-18888-AB

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Support bracket only, there is also a large support bracket that is also needed. Tilt and fixed steering columns.Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick.  Ford part number D0ZZ-3B139-A.

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Hooped support bracket only, there is also a large main bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3B139-A.

Sold as a pair. Replaces Ford Part # : D0OZ-8052 Check out our video on Radiator and Fan upgrades below:

Used pair of lower radiator brackets as taken from any 1971-73 Mercury Cougar or Ford Mustang. Additionally these will also fit 1970-71 Ford Torino / Fairlane and 1970-71 Mercury Montego / Cyclone. Should be for all engines. 250 6 cylinder, 302, 351, and 429. Right and left are different, plan on purchasing the insulating rubbers, they may not always be included. Ford part numbers D0OB-8052 or D0OZ-8052-A for passenger side, D0OB-8B381 or D0OZ-8052-B for the driver side. Check out our video on...

Fills the hole in the core support where the A/C lines pass through to the condenser. Replaces part # C9ZZ-19819.

Pair of reproduction cowl vent panel support pads.

This is the Left hand or driver side spring that holds the rear license plate or fuel door in the upright position. Fits all years of Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-B

This is the right hand or passenger side spring that holds the rear license plate or fuel door in the upright position. Fits 1967-68 and 1971-73 Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-A

This is the spring that holds the rear license plate or fuel door in the upright position. Fits 1969-70 Cougar.Ford Part #: C9WY-13455-A

Good aluminum piece that has no corrosion, no dings and all six mounting studs will be firmly in place. This same bezel was used on all Standard, XR7 or Eliminator Cougars for 1969 and 1970. Obviously the clock hole was not utilized on the Standard Cougar.

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.

Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Keep in mind that this sway bar does not come with mounting brackets or the end link kit.  

C9ZZ-5482-D Factory used sway bar for any 1969 Cougar with optional Competition Handling Package. Factory identified with a single 'Green' paint stripe. *Excludes 428CJ and Boss 302 cars, those cars were factory built with a 15/16 inch sway bar. This factory used front sway bar, does not include any mounting brackets or end link kits.

C7ZZ-5482-C This is a factory used sway bar for the Special Handling Package as found on with the 1967 and 1968 GT option. This bar was factory identified with a single 'Green' paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.