General (Old Category Structure)

XR7 style rear interior panel for 1970 Mercury Cougar hardtops. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. Arm rests sold separately.Specify if your needs require power window cutouts in the comments section.

XR7 style rear interior panel for 1970 Mercury Cougar hardtops. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. Arm rests sold separately.Specify if your needs require power window cutouts in the comments section.

[No Description Provided]

XR7 style rear interior panel for 1970 Mercury Cougar hardtops. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. Arm rests sold separately.Specify if your needs require power window cutouts in the comments section.

XR7 style rear interior panel for 1970 Mercury Cougar hardtops. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. Arm rests sold separately.Specify if your needs require power window cutouts in the comments section.

Used XR7 rear interior panel in nugget gold for the driver side (left hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Used XR7 rear interior panel in nugget gold for the passenger side (right hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.

[No Description Provided]

XR7 style rear interior panel for 1970 Mercury Cougar hardtops. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. Arm rests sold separately.Specify if your needs require power window cutouts in the comments section.

XR7 style rear interior panel for 1970 Mercury Cougar hardtops. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. Arm rests sold separately.Specify if your needs require power window cutouts in the comments section.

Used XR7 rear interior panel in saddle for the driver side (left hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Used XR7 rear interior panel in saddle for the passenger side (right hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.

This is a great option for our foreign customers who want to save on costly shipping charges and have a good plastic backing but their vinyl damaged. It will take some patience to stretch and glue this to your existing panel but it is not that hard. We seldom will have your color in stock (unless is is black) but please choose your desired color and we will do our best to accommodate you. We carefully remove these from panels with broken plastic and only save the really nice examples.

Reproduction bare rear interior panels for any 67 - 68 Cougar. These are not complete panels, but rather just the plastic backing, so keep in mind that you will need to use your existing upholstery or have them re-upholstered. Good for Standard or XR7. Sold as a pair.

These reproduction convertible panels only come in black and are sold as a pair. They DO NOT have the holes cut in them for the retracting seat belts, so 72 and 73 Cougar owners will need to cut these holes. In addition, you will have to cut the holes for the ashtray and power window switch or manual window crank as well as install the snaps for the top boot. This will of course require that you have your old panels to use as a guide. These panels are not as thick as the originals and if you...

Set of 1-1/4" leaf spring rubber bushings for the rear eye of the spring. Sold in packages of 8, 4 per side. Correct shackle bushings for all 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: C6ZZ-5781-B & C6DZ-5781-A.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

This reproduction fiberglass valance actually is better quality than you might guess... The mold was made from a NOS FoMoCo valance and as you look at the pictures you will notice that every tiny detail was mimicked. This is a good alternative for those trying to shed a few pounds as they are much lighter than OEM and keep in mind our steel reproductions are substantially heavier than OEM.Replaces Ford part # C9WY-6540544-A

Quality reproduction steel rear lower valance for the 1969 - 1970 Mercury Cougar. This Dynacorn reproduction is actually made of thicker stock than OEM. The original's weight is 4.6 lbs and this new reproduction weighs in at 5 lbs. We've tested this valance on a few of our cars and found them to fit exceptionally well. Mounting hardware is sold separate. Also available in fiberglass.Replaces Ford part # C9WY-6540544-A. ...

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford part # D1WB-6528519, Mercury MPC # D1WY-6528011-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford part # D1WB-6528518, Mercury MPC # D1WY-6528010-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

New old stock passenger side rear quarter panel extension. 1967-68 Mercury Cougar. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

This is the seal at the back of the booster on the Midland-Ross units.

Rear seat bottom or lower cushion from any 1969-70 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number C9WB-7663120.*Note - Does not fit coupe or fastback.Lower frame measures 46" at it's widest point and 18.5" high This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Rear seat bottom or lower cushion from any 1967-70 Mercury Cougar. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Replaces Ford part number C7WB-6563120. This part number or engineering number would have originally been stamped into a tag that was attached to the bottom side of the seat. *Note - Will not fit Mustang, Mustangs 1967-68 seat bottoms (C7ZB-6563120) are the same width as Cougars, but the seating portion...

Rear seat bottom or lower cushion from any 1971 Mercury Cougar or Ford Mustang coupe or hard top only. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Only fits 1971 cars due to the seat belt location in the floor. 1972-73 seats are a bit narrower, due to the seat belt retractors in the side panels.Replaces Ford part number D1ZB-6563120.*Note - Excludes 1972-73 Mustang and Cougar.

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Only fits 1972-73 cars due to the seat belt location in the side panels. 1971 seats are a bit wider.Replaces Ford part number D2ZB-6563120.*Note - Excludes 1971 Mustang and Cougar.

Rear seat back or upper cushion from any 1969-70 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Replaces Ford part number C9WB-7666700. This part number or engineering number would have originally been stamped into a tag that was attached to the bottom side of the seat. Though these seem to fit in a 64-70 Mustang convertible, the correct engineering number that would...

Rear seat back or upper cushion from any 1967-70 Mercury Cougar. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Replaces Ford part number C7WB-6566700.  This part number or engineering number would have originally been stamped into a tag that was attached to the back side of the seat.  There are claims that this part will also work in the Mustang coupe, but the 67 - 70 Mustang would have originally...

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang coupe or hard top. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-6566700.*Note - Does not fit convertible.

This is the seat belt bezel located on the rear interior panel on your 72 - 73 Cougar or Mustang. Without it, your belt would retract back into the panel and you'd have to remove the whole thing just to get to the belt again. These bezels are very hard to come by, and we have yet to find anyone who reproduces them. Keep in mind that these bezels have been sitting for over 40 years, so the plastic has most likely become hard and chalky. When ordering, be sure to mention what color you need, and...

This rear segment exhaust system is manufactured right here in the good old USA from original 1968 and 1969 Mercury Cougars. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

This 2-1/4 inch rear segment exhaust system is manufactured right here in the good old USA from an original 1971 M code Cougar with the 351C engine. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they...

This 2-1/4 inch rear segment exhaust system is manufactured right here in the good old USA from an original 1969 M code Cougar. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

This rear segment exhaust system is manufactured right here in the good old USA from an original 1967 S code Cougar. It is an OEM style direct replacement system that includes: 2 intermediate pipes, 2 mufflers, 1 transverse resonator, and a right and left tail pipe. The system is constructed from 2 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so...

This 2-1/4 inch rear segment exhaust  system is manufactured right here in the good old USA from an original 1971 429 Cobra Jet Cougar. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept...

This 2-1/4 rear segment exhaust system is manufactured right here in the good old USA from an original 1969 R code Cougar. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

6x9 Replacement for OEM package tray speaker. Comes pre-wired with the stock style pigtail to plug in to your original wiring. Sold individually, 2 required per car.

Kit includes one pair of 25 watt speakers (50 watts total peak) with correct pigtails and one pair of correct speaker grills with the exact screen pattern as original. Correct mount spacing utilizes the factory holes in your package tray, hardware included. This kit is 100% correct for the 1967 or 1968, but will work on the 69 or 70 as well. The Cougar package trays for the 69 and 70 came perforated from the factory for speakers, so the grills are not necessary. Thanks for the plug Mark!: "My...

Very good reproduction of the speaker grille located on the package tray in the 1967-68 Mercury Cougar and 1965-70 Ford Mustang. Includes the mounting hardware.  Sold individually.

Rear fender splash shield for the driver side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16103-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

The metal portion on the Mustang shield is identical to the 1967-68 Cougar rear shields, but the rubber is different between the Cougar and Mustang. We are in the process of trying to get the correct rubber for the Cougar. Replaces Ford Part # C7ZZ-16103-B.

Rear fender splash shield for the passenger side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16102-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

The metal portion on the Mustang shield is identical to the 1967-68 Cougar rear shields but the rubber is different between the Cougar and Mustang. We are in the process of trying to get the correct rubber for the Cougar. Replaces Ford Part # C7ZZ-16102-B.