General (Old Category Structure)

Used cover plate or thrust plate that retains the camshaft on the front of Ford small block V-8 engines such as 289, 302, 351W. 1967-70 Mercury Cougar or Ford anything. This plate has three bumps, we have found a Ford number of C9OZ-6269-A, this may be a service replacement number and could be found on engines built earlier than 1969. We have found this style of 289's from 1967. There is another version with Ford number C2OZ-6269-A, it only has two bumps.

Used cover plate or thrust plate that retains the camshaft on the front of Ford V-8 engines such as 351C, 351M, 400, 429, 429CJ, and 460. 1970-76 Mercury Cougar or 1968-76 Ford anything. We have found a Ford number of C8SZ-6269-A. 

Used cover plate or thrust plate that retains the camshaft on the front of Ford FE big block V-8 engines such as 352, 360, 390, 410, 427, 428, and 428CJ. 1963-70 Mercury Cougar or Ford anything. We have found a Ford number of C3AZ-6269-A, 

Reproduction plastic plate that goes between the dash bezel and dash pad on any 1967-68 Standard model Mercury Cougar with factory air conditioning. This is for the center vent and is has a Ford casting number of C7WB-65044E88.Note: The lip of the plate points downward. The plate slides in behind the dash face pad, see above photo for reference.

Used plastic plated plate that goes between the dash bezel and dash pad on any 1967-68 Standard model Mercury Cougar with factory air conditioning. This is for the center vent and is has a Ford casting number of C7WB-65044E88. These originally were chrome vacuum plated, like the dash. These will have some degradation or flaking chrome. No breaks or cracks on the plastic.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side lower only, marked with an "L". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502639-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side lower only, marked with an "L". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number C6OZ-6202639-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side upper only, kind of shaped like the State of Arizona, marked with an "L". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502667-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side upper only, marked with an "L". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number D1ZZ-6502667-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver and passenger side lower only, kind of shaped like the State of Utah. Fits driver and passenger side hinges. Fits any 1967 Mercury Cougar and Ford Mustang. Ford part number 6502667.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side lower only, marked with an "R". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502638-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side lower only, marked with an "R". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number C6OZ-6202638-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side upper only, kind of shaped like the State of Arizona, marked with an "R". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502666-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side upper only, marked with an "R". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number D1ZZ-6502666-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver and passenger side upper only. Fits any 1967 Mercury Cougar and Ford Mustang.Ford part number 6502666.

Floor tunnel body reinforcing plate for the floor shifter on any 1967-68 Mercury Cougar or 1965-68 Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than other years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number C5ZZ-6512118-A.

Floor tunnel body reinforcing plate for the floor shifter on any 1969-70 Mercury Cougar or Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than previous years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number C9ZZ-6512118-A.

Floor tunnel body reinforcing plate for the floor shifter on any 1971-73 Mercury Cougar or Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than previous years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number D1ZZ-6512118-A.

Used air cleaner base plug, plugs the area pre cut from the factory. Typically found on 70 - 73 Cougar and Mustang.

These are always rock-hard so if you plan on removing a seat and do not want to boil your old rubber parts to make them pliable enough to reinstall then you will want to pick a set of these up. Plug size: 1 1/2"   also used for the electric headlight conversion kit for the firewall pass through body plug.  

This plug will work on your 69 - 73 Standard or XR7 as well as the 69 - 73 Mustang. This plug housing is used to connect the under dash main loom to the gauge cluster.

Used voltage regulator plug for the 67 - 68 Mercury Cougar. Plug end only, does not include any wiring.

Used taillight wiring harness repair plug and pigtail to the driver side (left hand) center taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Used taillight wiring harness repair plug and pigtail to the driver side (left hand) inboard taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Used taillight wiring harness repair plug and pigtail to the driver side (left hand) outboard taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Used taillight wiring harness repair plug and pigtail to the passenger side (right hand) inboard taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source...

Used taillight wiring harness repair plug and pigtail to the passenger side (right hand) outboard taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source...

Used brake switch plug end, the one that plugs into the brake pedal switch for the brake lights. These often times get hot and partially melt. Easy to change, no cutting or splicing of wires. The female spade plug end just releases from the plug end, look for the release tab for beside the wire on the back.

Plastic plug end used to mate to the individual switches on a 1969.

This kit includes 33 pieces and has the quarter panel drain valves.

This kit includes all the rubber plugs needed for the inner cowl panel as well as two windshield stops. These plugs will help ensure your Cougar's cowl panel doesn't get damaged due to moisture or small pieces of road debris. Each of the eight (8) plugs are constructed from high-quality rubber and are designed to be OEM-style, direct-fit replacements.

This cup holder fits snug into the seat belt receptacles in your 69 Mustang or Cougar center console. Very useful cup holder that does not require modification to take in and out.

These are always rock-hard so if you plan on removing a seat and do not want to boil your old rubber parts to make them pliable enough to reinstall then you will want to pick a set of these up.Plug Size 1 1/2"

Set of 4 seat mounting access floor pan plugs, enough for one seat. 2 kits needed for both bucket seats. This is a good idea to pick up two sets of these when replacing carpeting. These are always rock-hard so if you plan on removing a seat and do not want to boil your old rubber parts to make them pliable enough to reinstall then you will want to pick a set of these up. Plug Size 1 1/2"

Single used post for 1968 dual post head rest. Sold individually, two used per head rest. Ambidextrous, can go on either side, notches to the inside. Comes as shown, chromed rod, nut and lock washer. Fits any 1968 Ford with dual post headrests.  

Cougar poster by WCCC, featuring a 1969 XR7 Convertible against a stunning sunset and impressive skyline, this 20" x 30" poster is printed on heavyweight archival paper and features a semi-gloss finish. Suitable for framing, this print would make a great decoration in your garage or living room.  *NOTE - Please excuse the typo on our phone number at the bottom of the poster! The phone number on our business cards and at the bottom of our website is correct. ...

New Cougar Drive-In poster by WCCC! This 20" x 30" poster is printed on heavyweight matte archival paper and features a satin finish. Suitable for framing, this print would make a great decoration in your garage or living room. This photo was taken at our annual Open House event in 2013.Here's a video of our 2013 Open House event! ...

This poster is a meticulous recreation of the 1968 original that Lincoln-Mercury dealerships had on display in their showrooms to advertise the Cougar XR7-G. We were able to have an original poster professionally scanned, the images were restored, and the text carefully recreated to match the original. The result is a fresh new version of a rare, iconic display piece.This poster is the same size as the original, an impressive 36" x 48", and printed on nice heavy stock. If you don't have that...

This poster is a meticulous recreation of the 1968 original that Lincoln-Mercury dealerships had on display in their showrooms to advertise the Cougar XR7-G. We were able to have an original poster professionally scanned, the images were restored, and the text carefully recreated to match the original. The result is a fresh new version of a rare, iconic display piece.This poster is the same size as the original, an impressive 36" x 48", and printed on nice heavy stock. If you don't have that...

Reproduction master cylinder decal for the 1967 - 1969 Mercury Cougar or Ford Mustang. This decal was not used on later year cars. These types of decals are for the person to whom details matter.  Customer feedback found at mercurycougar.net:  Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What are...

This is a good used and tested power harness which goes from the circuit breaker at the starter solenoid to any of the following:1. Heated backlight (rear defroster)2. Power seat3. Seat back release4. Convertible top

Power lead from starter solenoid to circuit breaker for any of the following: power windows, convertible top, automatic seat back release, headed back light or rear defog (1971-73), or power seat.Replaces Ford Part #: C9WB-14678-B

C1AZ-3C590-A Our Ford Master Parts Catalog only goes back to 1965. However, there is a listing for this "Bushing kit - Power steering cylinder mounting rod end". 1965 Mustang V-8 and 1965 Fairlane. It should fit a variety of Ford and Mercury cars from 1961-1965.OEM Ford new in the box Autolite. Kit consists of : 2 - C1AA-3A344-A  Insulator, 1 - AJ-3652-A Spacer, 2 - C3AA-3A345-A Washers, 1 - 33925-S8 Nut, 1- 45218-S8 Nut. ...

Remanufactured constant ratio power steering box for the Mercury Cougar or Ford Mustang equipped with factory power steering. These units are Saginaw 800 Series torsional power steering gear boxes that feature 4 turns lock to lock. In our experiences this box design is very durable and not prone to wear like the early style dry steering boxes. These units are tagged as SPA-S, SPA-U, SPA-AC, SPA-AE..*NOTE* This unit will work in any 1971-73 Mercury Cougar or Ford Mustang except for those...

This is the 'constant ratio' power steering box, Saginaw manufactured. Tag number SPA-S, and sometimes could also be SPA-U. This is the standard power steering box for all Cougars 1971 1972 1973. We offer used boxes because in our experiences this box design is very durable and not prone to wear like the early style dry steering boxes.

This is the 'variable ratio' power steering box, Saginaw manufactured. The Variable Ratio steering box was part of the Competition Suspension Package available optionally on all Cougars or part of the GT or 351CJ Performance Group.This Variable Ratio steering box should have come standard with all 1971 - 1973 M or Q code 351-4V or C or J code 429-CJ equipped Cougars. Sometimes this tag number could also be SPA-T, SPA-V, SPA-AD, SPA-AF,

Reproduction high pressure hose that goes from the control valve to ram cylinder for the Mercury Cougar or Ford Mustang. Ford updated this hose for the 1970 model year and uses the same part number as the early hoses, but with a double crimp. This unit features all of the correct ribbing, striping and crimping. Hose with 5/16 fittings used 1970 Mercury and Ford.*NOTE* Two different hoses attach between the control valve and the ram cylinder, PS7U8B and PS4U8A.Replaces Ford part...

C8ZZ-3A713-A Return or low pressure hose. Low pressure hose from the control valve to insulator. 1968-70 Mercury Cougar Ford Mustang all V-8 engines. All correct ribbing, striping, and crimping. Has correct colored protective sheathing. *Note - There are two halves to the low pressure hose from the control valve to the pump. This is the lower half only. Please see part number 42301 for the upper section that works with this hose.