Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 7201-7248 of 13234
$0 Price: $39.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 18884 -

Hardened from heat, grade B will crack if folded in half on a cold day. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake drum from it for a few days. Do know that all interior trim parts we sell will be discolored and will need to be...

$0 Price: $21.45

Buy Details

Availability: In-Stock Item
Item #: 31656 -

New pinion seal for any 8 inch third member found in 1967-73 Ford and Mercury cars. 1967-68 Mercury Cougar and all years of Mustang with 8 inch drop out rears.

$0 Price: $74.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23809 -

C3AZ-4730-B Rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1970 Mercury Cougar and Ford Mustangs. Good used part with solidly mounted metal threaded stud. Pinion bumper. The casting number seen on the 67-68 is C3AA-4906-C, this version has fine threads. The version most often seen on the 69-70 is C9OA-4906-A. It will have a coarse threaded mounting stud. Two of these were used on certain 1967 Shelby Mustangs with traction bars.

$0 Price: $55.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 30048 -

Used pinion yoke for an 8 inch rear end on any 1967-68 Mercury Cougar or 1967-73 Ford Mustang. 25 splines Ford says it is for a 1260 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3OZ-4851-A.

$0 Price: $49.10

Buy Details

Availability: In-Stock Item
Item #: 15-0157 -

Locking pawl catch pin and locking pawl pin for your 70-73 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to these parts can avoid several hundred dollars in damage. These...

$0 Price: $3.65

Buy Details

Availability: In-Stock Item
Item #: 41033 -

Reproduction Pitman Arm w/ 1" Sector Shaft Nut EACH for the 1967 Mercury Cougar or Ford Mustang

$0 Price: $100.05

Buy Details

Availability: In-Stock Item
Item #: 26170 -

1967 - 1970 Manual steering box pitman arm with 1-1/8 inch sector shaft. Replaces Ford part number C7ZZ-3590-B. Note that early 67's will have a 1" sector shaft. Check out this video

$0 Price: $119.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24213 -

C7ZA-3590-B 1967 - 1968 Manual steering box pitman arm with 1-1/8 inch sector shaft. Replaces Ford part number C7ZZ-3590-B. Check out this video

$0 Price: $99.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 18933 -

C9ZA-3590-B 1969 - 1970 Manual steering box pitman arm with 1-1/8 inch sector shaft. Replaces Ford part number C9ZZ-3590-B.

$0 Price: $136.45

Buy Details

Availability: In-Stock Item
Item #: 32248 -

Power steering pitman arm for any 67-70 Mercury Cougar or Ford Mustang with steering box with 1-1/8" sector shafts.  Replaces Ford part number C9ZA-3590-A This part with the casting number of C9ZA-3590-A was used starting in 1969, but was the service replacement pitman arm for 1967-68 cars too. Check out this video

$0 Price: $148.37

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 53197 -

Power steering pitman arm for any 1967-70 Mercury Cougar or Ford Mustang with steering box with 1-1/8" sector shafts. This part with the casting number of C9ZA-3590-A was used starting in 1969, but was the service replacement pitman arm for 1967-68 cars too. Check out this video

$0 Price: $92.75

Buy Details

Availability: In-Stock Item
Item #: 26169 -

Quality reproduction of the early 1967 Pitman arm for use with the 1 inch sector shaft from the steering box. Power steering only. Check out this video

$0 Price: $77.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23831 -

C4ZA-3590-A Early 1967 Steering box pitman arm with 1 inch sector shaft. Power steering only, used with SMB-E steering box. Fits early 1967 Mercury Cougar and 1965- early 1967 Ford Mustang. Ford part number C5ZZ-3590-A. Caution, measure your steering box sector shaft, many of the short boxes have been changed to the 1-1/8 inch boxes. Rare part, limited to stock on hand. Check out this video

$0 Price: $148.37

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24212 -

C7ZA-3590-C 1967 - 1968 Power steering box pitman arm with 1-1/8" inch sector shaft. Ford part number C7ZZ-3590-C. Check out this video

$0 Price: $105.55

Buy Details

Availability: In-Stock Item
Item #: 30128 -

This reproduction pitman arm equipped on 71 - 73 Cougars and Mustangs with factory power steering. Heavy-duty cast construction. Includes a new castle nut, cotter pin and zerk fitting. Replaces Ford part number D1ZZ-3590-B.

$0 Price: $72.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25387 -

D1ZA-3B153-BA 1971 - 1973 Power steering pitman arm. May also have casting number D3ZA-3B153-BB. Ford part number D1ZZ-3590-B.

$0 Price: $30.00

Buy Details

Availability: In-Stock Item
Item #: 15-0191 -

Reproduction pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and 2 - 4 are required per car. Pin is custom made on short runs and is very difficult to find. .001 undersized, and with 8/32 threads instead of 6/32 like the originals. Newer pin removal tools will fit. Replaces Ford part # C7SZ-3D739-A. Removing pivot pins on 67 - 69 tilt away columns: Work on the upper knuckle pivot pins as there is room...

$0 Price: $6.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 15-0123 -

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 8-32 thread. Ford part # D0AZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

MSRP:$39.99
$39.99 Price: $31.37

Buy Details

Availability: In-Stock Item
Item #: 12175 -

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1076 WHITE Led Plasma back up light bulb for your 67-68 or 71-73 Cougar, Mustang or anything else you might have that takes an 1076 bulb. Please note that these bulbs are ground sensitive. Specs: Power: 7.5 Watts Brightness: 300 Lumens Total life expectancy: 30,000 hours 2" Tall (1 3/8" extends out of the socket) Comparison image - Click to view full-size: Check...

MSRP:$39.99
$39.99 Price: $31.37

Buy Details

Availability: In-Stock Item
Item #: 10036 -

1967-68 and 1971-73 Cougar/Mustang used bulb 1076 for Backup Lights, see part # 12175 As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further.  These WHITE "Plasma" LEDs are a direct replacement for 1156 and will fit anything you might have that takes an 1156 bulb (or other bulbs with the same base configuration, such as 97 and 1003 bulbs).  Basically good for every car from 1950 to 1990 that uses a 1156...

MSRP:$39.99
$39.99 Price: $31.37

Buy Details

Availability: In-Stock Item
Item #: 10043 -

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

MSRP:$399.90
$399.90 Price: $260.87

Buy Details

Availability: In-Stock Item
Item #: 12222 -

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

MSRP:$119.97
$119.97 Price: $75.47

Buy Details

Availability: In-Stock Item
Item #: 10033 -

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

$0 Price: $17.95

Buy Details

Availability: In-Stock Item
Item #: 32672 -

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for any car that uses...

MSRP:$39.99
$39.99 Price: $31.37

Buy Details

Availability: In-Stock Item
Item #: 10006 -

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Plasma LED 1157 replacement bulb in YELLOW for your parking / running lights. Much brighter than stock, more responsive, and less power draw. We won't go so far as to call these little guys AMBER, but they're definitely yellow. Good for your 67 - 73 Cougar, Mustang or anything else that takes a dual-filament 1157 bulb for marker lights or turn signals. Specs: Power: 7.5...

MSRP:$39.99
$39.99 Price: $31.37

Buy Details

Availability: In-Stock Item
Item #: 33337 -

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1157 WHITE LED Plasma stop lamp / turn signal light bulb for your 67 - 73 Cougar, Mustang or anything else you might have that takes a white 1157 bulb. Please note that these bulbs are ground sensitive. Did you know that white (clear) 1157 bulbs fit a ton of other cars and trailers from the 50's clear through the 90's and beyond that used the...

MSRP:$12.00
$12.00 Price: $10.80

Buy Details

Availability: Discontinued, Limited Stock on Hand
Item #: 14245 -

24" hose with metal coil (like original) instead of plastic coil found in most. Coils are wrapped in a 6+ mil plastic rather than the 3 mil plastic that you can easily put your thumb through. Does not come with clips. May require being cut to fit some applications. 2 required per car. Replaces Ford Part #: B5A-18556-C.Replaces Ford Part #: B5A-18556-C.

$0 Price: $16.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 14-0100 -

This face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are going to be missing that piece, because after all......that dampener has been in there for up to 46 years! (this doesn't effect its useability). You can use your existing...

$0 Price: $24.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 14-0021 -

When placing your order, be sure to leave a note as to which color you're looking for and we'll do our best to find them for you. Limited quantities available. This colored face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are...

$0 Price: $17.35

Buy Details

Availability: In-Stock Item
Item #: 30884 -

These reproduction face plates fit inside the buckle bezel on the two piece type seat belt buckle cover. Sold as a pair. You can use your existing spacer, or if you're missing one, you can find it here. Check out our video "All about seat belts" below. ...

$0 Price: $0.85

Buy Details

Availability: In-Stock Item
Item #: 16136 -

New black plastic retainer for attaching the front license plate bracket to the bumper beam on all 1973 Mercury Cougar. Two total needed for installing the lower license plate bracket. These "T" shaped retainers very closely resemble the originals. *Note - These are included with the purchase of our used front license plate bracket.

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 14-0000 -

This is the complete one piece seat belt buckle cover which comes with the face plate (with the round cutout for the push button) and the bezel all in one. This version is handy when you don't want to deal with multiple parts (as is the case with the separate face plate and bezel version). Simply remove your old cracked or broken cover, replace the metal spacer, and pop this cover into place and you're ready to go! You can use your existing spacer, or if you're missing one, you can find it...

$0 Price: $14.85

Buy Details

Availability: In-Stock Item
Item #: 15-0162 -

Shrink-on plastic sleeve that is found on the lower part of the collapsible steering columns. Used sleeves are often ripped and torn. Simply cut off your old sleeve and install this item to give your column a newer look and feel. Installation: Make sure that your column is clean. Lube the column and inside of the sleeve. Do not remove the crease on the plastic, you need it to help you put the sleeve on the tube. Push the sleeve on as far as you can. Gently tap the sleeve down on a table top...

$0 Price: $20.57

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32098 -

Used cover plate or thrust plate that retains the camshaft on the front of Ford small block V-8 engines such as 289, 302, 351W. 1967-70 Mercury Cougar or Ford anything. This plate has three bumps, we have found a Ford number of C9OZ-6269-A, this may be a service replacement number and could be found on engines built earlier than 1969. We have found this style of 289's from 1967. There is another version with Ford number C2OZ-6269-A, it only has two bumps.

$0 Price: $20.57

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33595 -

Used cover plate or thrust plate that retains the camshaft on the front of Ford V-8 engines such as 351C, 351M, 400, 429, 429CJ, and 460. 1970-76 Mercury Cougar or 1968-76 Ford anything. We have found a Ford number of C8SZ-6269-A. 

$0 Price: $20.57

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33596 -

Used cover plate or thrust plate that retains the camshaft on the front of Ford FE big block V-8 engines such as 352, 360, 390, 410, 427, 428, and 428CJ. 1963-70 Mercury Cougar or Ford anything. We have found a Ford number of C3AZ-6269-A, 

$0 Price: $32.27

Buy Details

Availability: In-Stock Item
Item #: 32350 -

Reproduction plastic plate that goes between the dash bezel and dash pad on any 1967-68 Standard model Mercury Cougar with factory air conditioning. This is for the center vent and is has a Ford casting number of C7WB-65044E88.Note: The lip of the plate points downward. The plate slides in behind the dash face pad, see above photo for reference.

$0 Price: $15.17

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 21-0126 -

Used plastic plated plate that goes between the dash bezel and dash pad on any 1967-68 Standard model Mercury Cougar with factory air conditioning. This is for the center vent and is has a Ford casting number of C7WB-65044E88. These originally were chrome vacuum plated, like the dash. These will have some degradation or flaking chrome. No breaks or cracks on the plastic.

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 22220 -

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side lower only, marked with an "L". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502639-A.

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 22550 -

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side lower only, marked with an "L". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number C6OZ-6202639-A.

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 22552 -

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side upper only, kind of shaped like the State of Arizona, marked with an "L". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502667-A.

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 22559 -

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side upper only, marked with an "L". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number D1ZZ-6502667-A.

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 21619 -

Used door hinge anchor plate for attaching the door hinge to the body pillar. All positions are the same, upper, lower, driver and passenger sides. Fits all 1969-70 Mercury Cougar and Ford Mustang.Ford part number C9ZZ-6502666-A.

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 18742 -

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver and passenger side lower only, kind of shaped like the State of Utah. Fits driver and passenger side hinges. Fits any 1967 Mercury Cougar and Ford Mustang. Ford part number 6502667.

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 22542 -

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side lower only, marked with an "R". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502638-A.