General (Old Category Structure)

Driver side metal trim part that that runs along the interior roof edge and connects the "A" pillar plastic moulding to the rear window (quarter window) moulding on the inside. These came color keyed to the trim, most will need a fresh respray on interior paint. Please include desired color in the comments section and we will try to accommodate you if at all possible.

Metal trim part that connects the "A" pillar plastic moulding to the rear window (quarter window) moulding on the inside. These came color keyed to the trim, most will need a fresh respray on interior paint. Please include desired color in the comments section and we try to accommodate you if at all possible.

This two piece painted trim set helps to secure the dash pad in place at the bottom of the windshield. 1968 Mercury Cougar used a slightly shorter trim set due to the padded windshield pillar pads. The 1967 will work fine, all of holes line up the same. These 1967 trim pieces also have a smooth painted surface, 1968 Cougar pieces have a slightly textured painted finish. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as is for a driver quality car. Will...

Used driver side (left hand) lower rocker moulding / trim for the Mercury Cougar. There is a slight difference between the driver and passenger side mouldings and it is in the contour on the ends. These are not correct for the 1969 as the rear wheel opening was smaller in size and the 1970 had a factory screw hole at the rear. These 1970 mouldings are about 78-3/4" long. These almost always have one or two holes drilled in them are dull at the front due to road debris and have multiple small...

Used core grade rocker moulding for the driver side (left hand) of any 1971-73 Mercury Cougar. Right is the same as left on the 1971-73 Rocker Mouldings, we suggest you choose between passenger and drivers side when ordering as they are always duller up front from the tires throwing up road debris. They will come with minor dents and or scrapes, but no major dents or extra holes drilled. These are driver or core quality and are good for restoration, not show quality. Ships bare, without...

This rocker trim moulding is the same for right as left. Like many decades old NOS parts it will show some shelf wear. Ford part number D1WY-6510176-A

Used passenger side (right hand) lower rocker moulding / trim for the Mercury Cougar. There is a slight difference in the contour on the ends of this piece that differentiates driver and passenger side. These will not work on a 1970 as the rear wheel opening was increased in size for the 1970 model year. These 1969 mouldings are about 79-1/4" long. These almost always have one or two holes drilled in them are dull at the front due to road debris and have multiple small dings and scrapes....

Used passenger side (right hand) lower rocker moulding / trim for the Mercury Cougar. There is a slight difference between the driver and passenger side mouldings and it is in the contour on the ends. These are not correct for the 1969 as the rear wheel opening was smaller in size and the 1970 had a factory screw hole at the rear. These 1970 mouldings are about 78-3/4" long. These almost always have one or two holes drilled in them are dull at the front due to road debris and have multiple...

Used core grade rocker moulding for the passenger side (right hand) of any 1971-73 Mercury Cougar. Right is the same as left on the 1971-73 Rocker Mouldings, we suggest you choose between passenger and drivers side when ordering as they are always duller up front from the tires throwing up road debris. They will come with minor dents and or scrapes, but no major dents or extra holes drilled. These are driver or core quality and are good for restoration, not show quality. Ships bare, without...

Reproduction pair of moulding / outer dash trim pieces for the 69 - 70Cougar or Mustang.Replaces Ford Part #C9ZZ-6504718

Core driver side (left hand) rear quarter extension moulding / trim for the Mercury Cougar. This is a good trim part that is ready for restoration or could be used on a driver.Ford part # C7WY-6529313-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

NOS driver side (left hand) rear quarter extension moulding / trim for the Mercury Cougar. This piece will show some shelf wear so don't be surprised to find that this piece is not as nice as our restored moulding / trim.Ford part # C7WY-6529313-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

Restored driver side (left hand) rear quarter extension moulding / trim for the Mercury Cougar. We have many NOS trim parts in stock, but why bother when you can get correctly restored parts for less? This part has been "bright dip" anodized just like original and will not turn a chalky white color in a few months like one that has been polished only. If you select this option (paying a core charge), we will randomly select mouldings off the shelf. Paying the core charge does not mean you will...

NOS passenger side (right hand) rear quarter extension moulding / trim for the Mercury Cougar. These NOS pieces are getting difficult to source. If you have NOS parts, we will buy them!Ford part # C7WY-6529312-A.

Restored passenger side (right hand) rear quarter extension moulding / trim for the Mercury Cougar. This part has been "bright dip" anodized just like original and will not turn a chalky white color in a few months like one that has been polished only. Cores with minor dings or scratches are what is needed, smashed or folded trim parts cannot be restored. We are pretty liberal about these rear core exchanges, if you do not have a core, a similar core from a 1967-70 Cougar will usually suffice...

1968 Mercury Cougar left side or driver rear quarter moulding found on the GT-E models. This unique trim split the lower silver color from the body color. Good used core with a few minimal dings on the raised portion and will easily restore to mint condition. We won't always have this stick of trim in stock, but we will work to accurately describe the exact piece that we do have in inventory. We will take used GT-E trim in trade towards the reproduction GT-E trim call 503-463-1130 for...

Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit. Original Mercury part number is C7WY-6529035-A with a casting number of C7WB-6529035-D

Restored driver side (left hand) quarter window moulding / trim for the Mercury Cougar. These are correct for the coupe only. Correctly restored and re-anodized. 

Restored passenger side (right hand) quarter window moulding / trim for the XR7 Mercury Cougar. These are correct for the coupe only. Correctly restored and re-anodized.

Reproduction driver side (left hand) quarter window moulding / trim for the Mercury Cougar. This unit also comes with a used aluminum mounting bracket. Some refer to this unit as a "Hockey Stick" or "J moulding" and it mounts at the base of the rear quarter windows. These mouldings almost always need to be replaced due to pitting or having holes drilled in them to fasten them in place. We have found that this 3M product works great for bonding these mouldings / trim to the mounting bracket...

Reproduction passenger side (right hand) quarter window moulding / trim for the Mercury Cougar. This unit also comes with a used aluminum mounting bracket. Some refer to this unit as a "Hockey Stick" or "J moulding" and it mounts at the base of the rear quarter windows. These mouldings almost always need to be replaced due to pitting or having holes drilled in them to fasten them in place. We have found that this 3M product works great for bonding these mouldings / trim to the mounting bracket...

Restored quarter window to drip rail moulding / trim for the driver side (left hand) of the Mercury Cougar. This stainless trim part affixes to the "C" pillar and fills the gap between the roof side weather strip and drip rail gutter. Also known as "Roof Side Cover Retainer."

Restored quarter window to drip rail moulding / trim for the driver side (left hand) of the Mercury Cougar. This stainless trim part affixes to the "C" pillar and fills the gap between the roof side weather strip and drip rail gutter. Also known as "Roof Side Cover Retainer."

Stainless trim part that affixes to the "C" pillar. This trim part fills the gap between the roof side weather strip and drip rail gutter. Also known as "Roof Side Cover Retainer"

Used quarter window to drip rail moulding / trim for the driver side (left hand) of the Mercury Cougar. This stainless trim part affixes to the "C" pillar and fills the gap between the roof side weather strip and drip rail gutter. Also known as "Roof Side Cover Retainer."

This obscure little part fills the gap on the underside of the roof rail where the rear 1/4 window meets the "C" pillar. Also known as "Roof Side Cover Retainer"

This obscure little part fills the gap on the underside of the roof rail where the rear 1/4 window meets the "C" pillar. Also known as "Roof Side Cover Retainer"

This obscure little part fills the gap on the underside of the roof rail where the rear 1/4 window meets the "C" pillar. Also known as "Roof Side Cover Retainer"

This obscure little part fills the gap on the underside of the roof rail where the rear 1/4 window meets the "C" pillar. Also known as "Roof Side Cover Retainer"

Black is currently out of stock. We have green. This good used plastic radio trim part has been inspected for cracks and scrapes and has been found to be in good used condition. These original parts are better quality than the repros and unlike the reproductions you can buy them individually. Please select a color and we will attempt to accommodate. Plan on these used plastic parts needing to be painted.

Currently out of black. Our used plastic radio trim piece has been inspected for cracks and scrapes and has been found to be in good used condition. These original parts are better quality than the reproductions, and unlike the reproductions, you can buy our used trim parts individually. Please select a color and we will attempt to accommodate. Plan on these used plastic parts needing to be painted.

These plastic vertical trim parts mount under the dash pad, to the right and left of the radio. Available in black only, sold as a pair and "almost" as nice as our originals but you will notice the grain (texture) is less defined on the reproductions. We have perfect used in an array of colors. *Customer Feedback* "I have checked out this website several times and it is a great source for information and these guys know what they are talking about. They are friendly and willing to help with...

Economy reproduction aluminum rear deck lid moulding / trim for the 1967 - 1968 Mercury Cougar (will also fit on 1969-1970). This reproduction is as close to the original as possible, except for the fact that the clips included have 8mm nuts, unlike the originals. There is however one small problem, the metal on these mouldings is much softer than the originals and you have to take extra care when installing the clips, if you apply too much pressure when installing, you will dimple the...

Restored aluminum rear deck lid moulding / trim for the Mercury Cougar. If you do not have cores that are worthy of restoration we do have them for sale. The better core you start out with, the better the end result will be! If you prefer a mirror like luster then I suggest you purchase the 1969-70 deck moulding as stainless offers a much brighter finish. Seven clips are used to install the deck lid moulding and we have new clips available here. We will accept extra cores in on exchange for...

1969 - 1970 Cougars came factory equipped with stainless trunk mouldings and 1967 - 1968 Cougars came equipped with anodized aluminum trunk lid mouldings. However if you ordered a 67-68 service replacement deck moulding from Ford anytime after 1968 you would have received a stainless steel replacement. We recently obtained 15 of these that were stored improperly where the packaging had deteriorated and the mouldings showed shelf wear. We sent them out to be polished and the results are...

This is a freshly restored 1969-70 original stainless steel deck lid moulding. It has had all minor dings and creases it may of had professionally removed and has been polished to a mirror like, better than N.O.S. finish. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967-68 Cougar is that it will not match the aluminum corner mouldings perfectly. Seven clips are...

This option REQUIRES sending your core in advance. This is a freshly restored 1969-70 original stainless steel deck lid moulding. It has had all minor dings and creases it may of had professionally removed and has been polished to a mirror like, better than N.O.S. finish. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967-68 Cougar is that it will not match the...

Used stainless steel deck or trunk moulding / trim for 1969-70 Mercury Cougar, including convertible. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967-68 Cougar is that it will not match the aluminum corner mouldings perfectly. This being a used, means that it will have minor scratches, and a small dent or two. Save your old mounting clips, these are sold without...

This part will have a crack, usually at the top. Convertible and coupe used the same plastic trim. Add your desired color in the comments section.

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

Very hard to come by in perfect condition with no cracks. Both coupe and convertible use the same piece.

This plastic part will have a minor crack at the top. Add desired color into the comments section.

REQUIRES sending your cores in advance.This is a restored aluminum hood trim from an early 1971 Mercury Cougar or Ford Mustang. Rear of hood trim Ford part # D1ZZ-16B918-A. Our restored aluminum trim is correctly bright dipped or anodized like originals.Technically this trim piece was only used during the first 6 months of production on 1971 Mercury Cougar and all XR7 models including  convertibles. 1971 Ford Mustang. These will fit all third generation years 1971-73 Mercury Cougar...

Our core driver (left hand) lower rear aluminum window mouldings / trim will have some scratches and dings and are suitable for restoration. We will not send you kinked or gouged trim as it is not feasible to restore heavily damaged trim.Ford part # D1ZZ-6542405-A.

Restored driver side (left hand) lower rear window moulding / trim for the Mercury Cougar. This is the same part as the 1969-70 piece, however those pieces will carry a part number beginning in C9WY.Ford part # C7WY-42405-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim...

Used driver side (left hand) lower rear window moulding / trim for the Mercury Cougar. This is the same piece as the 1969-70 piece, however those pieces carry a part number beginning in C9WY. Ford part # C7WY-42405-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section. Also,...

Used driver side (left hand) lower rear window moulding / trim for the Mercury Cougar.