General (Old Category Structure)

Good core carburetor with number C9OF-E on the base. This equates to an Autolite 4300 4 barrel carburetor. Application is 1969 B and C body Ford cars such as Torino, Fairlane, Ranchero, Montego, Cyclone, or Comet with S code 390-4V engines and automatic transmission.Replaces Ford part number C9OF-9510-E.

1968 302-4V Autolite 4300 carburetor, Manual 3 or 4 speed transmission 50 States. Fits 1968 Mercury Cougar or Ford Mustang. C8ZF-C stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1968 302-4V Autolite 4300 carburetor, Automatic C4 transmission- 50 States. C8ZF-D stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1969 390-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - All 50 states. C9ZF-E stamped on the carburetor base, 1.25" venturi size and 600 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top.

1967 390-4V Holley 4150 carburetor, automatic C6 transmission - 49 states. C70F-9510-B stamped on the carburetor air horn, Holley list #3794, 600 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. S code 390-4V and 390GT engines with automatic transmissions. *Note not for DSO 52 and DSO 53 California destined cars.

1967 390-4V Holley 4150 carburetor, 3 or 4 speed manual transmission - 49 states. C70F-9510-A stamped on the carburetor air horn, Holley list #3793, 600 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. S code 390-4V or 390GT engines manual transmissions.. *Note not for DSO 52 and DSO 53 California destined cars.

1968 390-4V Holley 4150 carburetor, automatic C6 transmission - All 50 states. C8OF-9510-D stamped on the carburetor air horn. Holley list # 3796, 600 cfm.  Core carburetor with proper numbers.  This rebuildable core part may or may not include: the factory Ford Autolite tag that was affixed to the toptransfer tube good choke assembly

1970 428CJ-4V Holley 4150 carburetor, automatic C6 transmission - all 50 states. D0ZF-9510-AD stamped on the carburetor air horn. Holley list #4516, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *With air conditioning. Current carburetor has a date of 964 on the body. *Excludes Super Cobra Jet.

1970 428CJ-4V Holley 4150 carburetor, automatic C6 transmission - all 50 states. D0ZF-9510-AD stamped on the carburetor air horn. Holley list #4516, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *With air conditioning. This carburetor has been previously restored, we have noticed that one of the metering blocks has the wrong number. Still has the manual choke lever, and has a throttle kicker. Look carefully, some...

This Holley 4150 carburetor is for the1968 427-4V engine equipped with the C6 automatic transmission. This carburetor was used on cars for all 50 states with Holley list #4088. This is a 600 cfm core carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top, transfer tube, or good choke assembly on our cores. GT-E C6 automatic only. Current listing is a Ford service replacement carburetor. It has a date of 964 on the horn.Part # C8AF-9510-AD...

New Street Avenger carburetor. The 350 CFM Street Avenger carburetor has great features such as optimized street calibrations...two vacuum ports for all necessary vacuum accessories, factory preset electric choke for easy startups, built-in fuel filters; and an included 3/8" fuel line connection so there are no unnecessary trips back to the parts store. Known to bolt in right out of the box. The Avenger series are the first carburetors to have a limited lifetime warranty. With a great...

1972 351CJ-4V Motorcraft 4300D Carburetor, automatic C6 transmission- 49 states. D2ZF-BB stamped on the carburetor base, spreadbore design of 715 cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Not for DSO 52 or DSO 53 cars destined for California.

Basic kit for rebuilding your Ford Autolite or Motorcraft 2100 or 2 barrel carburetor. Covers all factory 2 barrel carburetors on any 1967-73 Mercury Cougar and Ford Mustang with Autolite or Motorcraft 2100 carburetors. Excludes later 2150 carburetors.

Lower carburetor gasket for all 1973 Mercury Cougar and Ford Mustang with 351C-2V engines. Lower gasket goes between the stock EGR spacer plate and the stock cast iron intake manifold.

Carburetor gasket for all 1972 Mercury Cougar and Ford Mustang with 351C-2V engines. This is a new gasket meant for use with stock Ford intake manifolds and correct Autolite/Motorcraft 2100 carburetors. Single gasket as shown, if you have a carburetor spacer plate you would need two gaskets.

Upper carburetor gasket for all 1973 Mercury Cougar and Ford Mustang with 351C-2V engines. Upper gasket goes between the stock EGR spacer plate and the stock Motorcraft 2100 carburetor.

Carburetor idle mixture screw caps like originally came on the cars from the factory. Exact reproduction of Ford part number C7AZ-9J500-A. This clip onto the idle mixture screws of any 1967-73 Autolite or Motor Craft carburetor 2100 or 4300. They also will fit the 429 Cobra Jet with Ford numbered Rochester Quadrajet carburetors in 1970-71. Sold as a PAIR.

5/16-24 hex nut 7/16" head that is used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts. Sold individually. AMK B-12786

This is a set of four 7/16 nuts that are used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts. 

This is the complete eight piece kit that includes four 7/16 nuts and four studs (1 3/8") which are double threaded. One end is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with NO spacer.

This is the complete eight piece kit that includes four 7/16 nuts and four double threaded studs (2 1/2"). One end of the stud is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with a 1" spacer.

This is the complete eight piece kit that includes four 7/16 nuts and four double threaded studs (1 3/4"). One end of the stud is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with 1/4" to 3/8" spacers.

Replaces Ford part # 351089-S Zinc (dark silver) finish Sold individually

Very nice reproduction stainless steel, carburetor deflector gasket for W code GT-E 427-4V engines. American made stainless steel plate with tabs, copied from an original.  Order of installation: Open gasket #15292, SS plate #31256, Phenolic spacer #41936, paper gasket #11813, Holley 4088 carburetor. Originally the spacer was part of the spacer assembly which had Ford part numbers of:  C8AZ-9A589-C,  Engineering number C8AE-9A589-EFord Technical Service Bulletin using...

Factory cast aluminum two barrel carburetor spacer plate. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. Fits all Ford 2 barrel carburetors, bore size is 1-5/8 inches in diameter. ...

Nice quality reproduction of the bake-o-lite carburetor spacer plate for all 1966-67 S-code 390-4V engines. Measures 0.28" thick, with small vacuum hose nipple on rear replaces Ford Part Number C6AZ-9A589-B. Fits 67 Cougar 390 Fits 67 Mustang 390 Fits 66 Fairlane 390 Fits 67 Fairlane 390 Fits 66 Cyclone 390 Fits 67 Cyclone 390 Check out the very first Cougar in our video below! ...

Measures 0.28" thick, with small vacuum hose nipple on rear Ford Part Number C6AZ-9A589-B. Mint condition original part.

15/16" thick aluminum with 5/8" heater nipples & 5/8" PCV hose nipple on rear. Casting number C9ZE-9A589-A.

CARBURETOR SPACER PLATE, 0.28" thick, has correct straight 1/2" PCV hose nipple in rear. Replaces Ford Part Number DOOZ-9A589-A. PCV System overview courtesy of Mansfield Mustang.

Good Quality spacer that measures 1 1/8" tall. Comes with PCV hose clamp and vacuum port cap. This was used on all 289, 302, 351w motors with a 4V carburetor.

Factory cast aluminum four barrel carburetor spacer plate, one inch tall. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. *excludes Boss 302 Eliminator ...

New 390 2BBL Carburetor spacer gasket for the 1968 X code 390-2V engine. Two needed per installation, one on both sides of the spacer plate.

New carburetor spacer plate gasket for all 1969 Mercury Cougar or Ford Mustang with S code 390-4V or 390IP original Autolite Carburetors. Additionally it fits all Ford installed Holley carburetors. This is the carburetor spacer to manifold gasket. Upper gasket between spacer and carburetor also available. This carburetor gasket also works well with most aftermarket Holley and Edelbrock carburetors.

New carburetor gasket for 67 - 70 Cougar or Mustang with 390 or 428 cobra jet engines and Ford numbered Holley carburetors. One or two needed per installation (with or without spacer plate) sold individually.

New carburetor gasket for all 289-4V, 302-4V, and 351-4V, Mercury and Ford cars from 1964-1970. Same gasket used between intake manifold and spacer, and spacer and carburetor. Sold individually, 2 required for complete installation with Ford 1 inch factory spacer and correct numbered Autolite 4300 carburetors.

Concourse Correct Hollow Left Rear Stud for the Carburetor Vacuum port to the C6 transmission modulator hose Replaces Part # 382768-S8

Since we do not have near enough of these used inner panels to go around, we are offering this cardboard template for purchase for those of you that would like to make your own. With the pictures we provide and the template one should be able to produce a reasonable facsimile. If you are really talented and think you would like to make them in quantity let us know! We would be interested in purchasing them.Click on images to enlarge. The picture above is the support strip that runs through the...

Since we do not have near enough of these used inner panels to go around, we are offering this cardboard template for purchase for those of you that would like to make your own. With the template one should be able to produce a reasonable facsimile. If you are really talented and think you would like to make them in quantity let us know! We would be interested in purchasing them.

Since we do not have near enough of these used inner panels to go around, we are offering this cardboard template for purchase for those of you that would like to make your own. With the template one should be able to produce a reasonable facsimile. If you are really talented and think you would like to make them in quantity let us know! We would be interested in purchasing them.

We have not been able to find an exact match for Aqua, here are the original color swatches from Ford: Here are the closest options we have found: 33-1965 Medium Aqua / Teal (closest, but too light) 25-021 Dark Aqua / Dark Green-Blue (too green) 29-880 Midnight Blue (Almost Black) Give your Cougar the added comfort of a extra 5/8" of Heavy padding under the carpeting and almost 30 lbs of Sound Deadening material. The mass backing gives your carpet the plush feel of the carpeting in a new...

Of the multiple carpets available out there these are the best. These are correctly molded to the contour of your floor pans and have the correct thickness of insulation bonded to the backside. They come with the correct heel pad sewn into the drivers side and have the correct hem in the appropriate places.*NOTE* 1969-70 Cougars did not originally come with a sewn in toe pad like the 1967-68 Cougars. These carpets do in fact come with the toe pad so if you want to be 100% correct with your car...

We have not been able to find an exact match for Aqua, here are the original color swatches from Ford: Here are the closest options we have found: 33-1965 Medium Aqua / Teal (closest, but too light) 25-021 Dark Aqua / Dark Green-Blue (too green) 29-880 Midnight Blue (Almost Black) Give your Cougar the added comfort of a extra 5/8" of Heavy padding under the carpeting and almost 30 lbs of Sound Deadening material. The mass backing gives your carpet the plush feel of the carpeting in a new...

Of the multiple carpets available out there these are the best. These are correctly molded to the contour of your floor pans and have the correct thickness of insulation bonded to the backside. They come with the correct heel pad sewn into the drivers side and have the correct hem in the appropriate places. *NOTE* 1969-70 Cougars did not originally come with a sewn in toe pad like the 1967-68 Cougars. These carpets do in fact come with the toe pad so if you want to be 100% correct with your...

We have not been able to find an exact match for Aqua, here are the original color swatches from Ford: Here are the closest options we have found: 33-1965 Medium Aqua / Teal (closest, but too light) 25-021 Dark Aqua / Dark Green-Blue (too green) 29-880 Midnight Blue (Almost Black) Give your Cougar the added comfort of a extra 5/8" of Heavy padding under the carpeting and almost 30 lbs of Sound Deadening material. The mass backing gives your carpet the plush feel of the carpeting in a new...

Of the multiple carpets available out there these are the best. These are correctly molded to the contour of your floor pans and have the correct thickness of insulation bonded to the backside. They come with the correct heel pad sewn into the drivers side and have the correct hem in the appropriate places. *NOTE* 1969-70 Cougars did not originally come with a sewn in toe pad like the 1967-68 Cougars. These carpets do in fact come with the toe pad so if you want to be 100% correct with your...

Give your Cougar the added comfort of a extra 5/8" of Heavy padding under the carpeting and almost 30 lbs of Sound Deadening material. The mass backing gives your carpet the plush feel of the carpeting in a new luxury car while adding a great deal of sound deadener to muffle road noise. The mass backing combined with the foil heat shield (Part # 10330) should provide sound deadening equivalent to that of the factory sound deadener. Of the many carpets available out there these are the best....

Of the multiple carpets available out there these are the best. These are correctly molded to the contour of your floor pans and have the correct thickness of insulation bonded to the backside. They come with the correct heel pad sewn into the drivers side and have the correct hem in the appropriate places.*NOTE* 1969-70 Cougars did not originally come with a sewn in toe pad like the 1967-68 Cougars. These carpets do in fact come with the toe pad so if you want to be 100% correct with your car...

Of the many carpets available out there these are the best. They are made with the correct 25 ounce Nylon, molded to the contour of your floor pans and have the correct thickness of insulation bonded to the backside. They come with the correct heel pad sewn into the drivers side and have the correct hem in the appropriate places. For a more plush carpet and added sound deadening, check out our Mass Back carpet kits.