1968 Mercury Cougar

C8TE-9425-A Cast iron intake manifold used on all 1968 X code 390-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold, used after 1-9-1968. Take off manifold with correct casting number of C8TE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C5AZ-9424-R. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

C7TE-9425-G Cast iron intake manifold used on all 1968 X code 390-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold, used before 1-9-1968. Take off manifold with correct casting number of C7TE-9425-G. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C5AZ-9424-P. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

C7AE-9425-F Cast aluminum intake manifold used on all 1968 W code 427-4V engines in a Mercury Cougar GT-E or 1968 Ford Mustang Shelby GT-500 (non KR models). Stock 4 barrel intake manifold. Take off manifold with correct casting number of C7AE-9425-F. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C6AZ-9424-H. *TRIVIA* This is also known as the PI aluminum intake manifold, PI = Police Interceptor. ...

Cast aluminum Sidewinder intake manifold. Over the counter speed part for the 427 Medium Riser. The offset carburetor placement was to help provided equal length runners in regards to flow. Single 4 barrel intake manifold as shown. Looking closely at the photos, this one has had a repair performed in the past. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford casting number C6AE-9424-J.

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers so if speaker holes are needed you will have to use your old panels as a template to drill holes in these "Mustang" reproductions. Replaces Ford Part number C7WY-650345-A1G / Casting number as seen on the back of the driver side will read C7WB-6502345-BW

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Reproduction interior kick panels in parchment / off-white for the Mercury Cougar or Ford Mustang. Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

AS OF NOW, THERE IS NO MANUFACTURER MAKING LEATHER UPHOLSTERY. THIS ITEM IS NO LONGER AVAILABLE FROM WCCC.Accurate, show quality reproduction 1968 XR7 Black interior seat kit (code 6A). Seats sewn with quality leather inserts with correct vinyl sides and backs with accurate stitching. These interior kits feature leather inserts with graining like the original XR7 leather seats which includes very smooth leather on the center and a rough grain on the perimeter. Kits come with a pair of upper...

AS OF NOW, THERE IS NO MANUFACTURER MAKING LEATHER UPHOLSTERY. THIS ITEM IS NO LONGER AVAILABLE FROM WCCC.Accurate, show quality reproduction 1968 XR7 Black front seat interior kit (code 6A). Seats sewn with quality leather inserts with correct vinyl sides and backs with accurate stitching. These interior kits feature leather inserts with graining like the original XR7 leather seats which includes very smooth leather on the center and a rough grain on the perimeter. Kit comes with a pair of...

AS OF NOW, THERE IS NO MANUFACTURER MAKING LEATHER UPHOLSTERY. THIS ITEM IS NO LONGER AVAILABLE FROM WCCC.Accurate, show quality reproduction 1968 XR7 Black rear seat interior kit (code 6A). Seats sewn with quality leather inserts with correct vinyl sides and backs with accurate stitching. These interior kits feature leather inserts with graining like the original XR7 leather rear bench with upper and lower seat skins. Keep in mind the rear seats were primarily vinyl with only the very top...

AS OF NOW, THERE IS NO MANUFACTURER MAKING LEATHER UPHOLSTERY. THIS ITEM IS NO LONGER AVAILABLE FROM WCCC. Accurate, show quality reproduction 1968 XR7 hard top parchment / off-white interior seat kit (1968 code 6U). Seats sewn with quality leather inserts with correct vinyl sides and backs with accurate stitching. These interior kits feature leather inserts with graining like the original XR7 leather seats which includes very smooth leather on the center and a rough grain on the perimeter....

AS OF NOW, THERE IS NO MANUFACTURER MAKING LEATHER UPHOLSTERY. THIS ITEM IS NO LONGER AVAILABLE FROM WCCC. Accurate, show quality reproduction 1968 XR7 hard top off-white / parchment front seat interior kit (1968 code 6U). Seats sewn with quality leather inserts with correct vinyl sides and backs with accurate stitching. These interior kits feature leather inserts with graining like the original XR7 leather seats which includes very smooth leather on the center and a rough grain on the...

AS OF NOW, THERE IS NO MANUFACTURER MAKING LEATHER UPHOLSTERY. THIS ITEM IS NO LONGER AVAILABLE FROM WCCC. Accurate, show quality reproduction 1968 XR7 hard top Parchment / Off-White rear seat interior kit (1968 code 6U). Seats sewn with quality leather inserts with correct vinyl sides and backs with accurate stitching. These interior kits feature leather inserts with graining like the original XR7 leather rear bench with upper and lower seat skins. Keep in mind the rear seats were primarily...

Reproduction intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

Used intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

Rubber isolator used in tilt away steering column near the lower bearing. Two required per car. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction jack and tool bag for the trunk area of your Cougar or Mustang. Made in the same plaid style as the trunk mat on the outside, and a white soft liner on the inside. Measures 16 1/2" x 8 1/2"

This is the original JB Weld. We decided to bring this stuff in as a convenience to you, our customers. Why not buy a pack so that the next time you need to bond something together, you'll have a couple of tubes handy? No need to get up and go to the hardware store. With just a few clicks of your mouse, you can have it at your door in a few days (more or less, depending on your location). Good for all sorts of projects around the house or garage.

This mounts at the top front corner of the driver side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B.You may also need the attaching screw. Replaces Ford part number C7WY-6531491-B or C7WB-6531491. Fits 67 CougarFits 68 CougarFits 68 Mustang with body code 65B ...

This mounts at the top front corner of the passenger side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B.You may also need the attaching screw. Replaces Ford part number C7WY-6531490-B or C7WB-6531490. Fits 67 CougarFits 68 CougarFits 68 Mustang with body code 65B ...

Factory knob for the new for 1968 rear window defogger. This is the knob for the 2 speed fan switch mounted to the bottom dash on cars so equipped. Rare option, we try and match these up to the switches. Spares occasionally come in, subject to availability.

Good reproduction of a knob that is always broken off. Made from milled aluminum rather than plastic as the originals were made. This makes it so it is not as susceptible to breaking off. Unique to Cougars with tilt columns in 1968 - 1969. Replaces Ford part number C8MY-17513-C. This part also fits the 68-69 Mustang, Lincoln, Marquis, Thunderbird and other like models with an adjustable steering column.

Used emergency flasher knob for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is a very fragile part which we never find in good used condition. What you will see when it has been broken off is an exposed Phillips screw head. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes...

Hard to find knob with no crack or peeling issues, correct for right or left side Torino, Cougar, Mustang. Not for use with console equipped Mustang and Cougar. Casting number is C8OA-18A932-B.

Used on the Mercury Cougar or Ford Mustang with a factory center console and measures 1-3/8 inches tall. Replaces part # C8ZA-8A932-B

This is correct for your 1968 non console Mustang or Cougar. Fits left or right, no cracks or peeling. Casting number is C8ZA-18817-E.

Reproduction radio knob used on Mercury Cougar or Ford Mustang with a factory center console. Replaces part # C8ZA-18817Fits: 1968 Mercury Cougar

Used on Mercury Cougar or Ford Mustang with a factory center console. Replaces part # C8ZA-18817Fits:1968 Mercury Cougar

Used wiper knob for any 1968 Mercury Cougar. This detachable knob with set screw is slightly larger than the ones found in 1967. Good condition, will have a small rust pit or two.

This set of knobs is for 1968 Cougar / Mustangs without factory console. The exception to the rule would be the XR7G. Cougars equipped with a console need the longer version of this knob to clear the padded console face. If you happen to have a 1969 or newer radio then the radio has longer shafts and these knobs may in fact work with a console. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and...

Good used set of four knobs for your Mercury Cougar or Ford Mustang with a factory center console. These are plastic and much deeper than the non-console version. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 1968-70 AM radios with rear speakers and 1968-70 AM-FM radios, if you need the white spacer we offer it here. Our blow-out price is based on the fact that these are now available new! Knob length 1 1/2"Sleeve length 1 5/16" ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used upper knuckle for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang.  There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...

This is the factory Ford remote trunk latch as used on luxury cars such as Thunderbird or Lincoln. As you can see from the photo, they are made (and install) exactly like our Cougar trunk latches, but with the addition of a release tab. These can be installed to use either a cable, vacuum, or solenoid release.

Leaf Springs shipping time is 8-12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...

This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with gloss black accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking...

Reproduction Legendary GT9 series aluminum wheel in the natural finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

The 1967 Cougar was Mercury's attempt to enter the Pony Car market segment popularized by the April 1964 introduction of Ford's Mustang. Introduced in the fall of 1966 for the 1967 model year, the first-year 1967 Cougar exceeded all sales expectations with 150,893 units sold. It was selected as Motor Trend's 1967 Car of the Year. Legendary Cougar Magazine is dedicated to the first three generations of Mercury's luxury Pony Car. Each bi-monthly issue includes features on the first-generation...

Used " Red " high beam indicator lens for the Mercury Cougar. This is for late 1968 which uses the small housing. The 1967 lens was blue in color. The lens may have a slight arc to it due to the heat from the bulb over time.

Used high beam indicator lens for the 68 XR7 Cougar.

Used grade "B" rear courtesy / opera light lens for the Mercury Cougar. Opera lights were came as standard equipment on all XR7 Cougars, but were installed on many decor and standard level Cougar interiors. These units will have a few "warts" which show up as pitting in the chrome and may also have some minor cracking in the lens. If you just need a lens for your driver quality car, these are a great option. But if you compare this grade "B" lens to our reproductions, it will look like...

Used Carter fuel pump lever. From Carter made fuel pump as installed on Ford 352, 390, 410, 427, 428CJ FE engines. Many of the Carter "X" fuel pumps with screw together rebuildable pumps often times have Ford small block levers. Housings are he same. Levers are removable, see youtube for the rebuilding and assembly procedure.

These plates show almost no wear and would look right at home on a show car.NOTE: The plates and plate numbers pictured are exactly what you'll receive.

These plates show average wear and can be used as is, or restored to look new.NOTE: The plates and plate numbers pictured are exactly what you'll receive. 

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair could use a bit of restoring to get back to perfect condition, but they are in good shape and will not have any extra holes like the grade B plates do.   NOTE:  "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair has extra holes drilled, which would need to be repaired (see pictures). They could be restored or used as-is. Because of this, we're selling them at a reduced price. NOTE: "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

Rechromed GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine, that did not come with the GT package, would have used the painted air cleaner lid. Replaces Ford part # C7OZ-9661-A.*NOTE* The outside dimension of the lid is 16.75 inches and will not fit the...

This used assembly includes lamp socket, bracket, mercury switch, and length of wire.Replaces part # C7ZB-15702-A