Exhaust

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

These are 100% correct reproductions for the 1968 Mercury Cougar XR7-G, but will fit any 1967-68 Cougar. These will NOT lay flat against the valance, as the originals did not. These are beveled on purpose and if you attempt to straighten them they WILL break. The reproductions that do lay flat against the valance are no longer being produced. We cannot warranty these against any attempts to straighten them. Sold as a pair. ...

Band or ring style factory exhaust pipe clamp. For 2 inch outside diameter exhaust pipes. Comes with a course sheet metal type threaded hex head bolt. Ford part number C5DA-5A272-B. *Note all 1967 & 1968 Cougars had 2 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C6AA-5A272-A is the factory style 2-1/4" tailpipe clamp.

Concours reproduction horseshoe clamp with correct style of nuts. Used on all 1967 - 1973 models with 2 inch exhaust tips. Correct for XR7-G, GT-E, Mustang GT, Shelby Mustang, all Ford.   Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp and correct style of nuts. Used on all 1968 - 1971 models with 2-1/4" exhaust. Correct for Boss 302, Boss 429, Shelby Mustang, all Ford with 2-1/4 inch exhaust at the H - Pipe.  Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1967 - 1973 models with 2" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1968 - 1973 models with 2-1/4" exhaust. Many of the stock exhaust systems were actually 2 inches. Most reproduction "Systems" are 2-1/4, use accordingly. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Reproduction dual exhaust tip to hanger clamp for the 1967 - 1970 Mercury Cougar and Ford Mustang.

Reproduction pair of exhaust pipe clamps for your 67 - 69 Cougar or Mustang.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

Concours correct engine pipe donut, metal, factory original dual sized design to properly seal H-pipe to Exhaust manifolds MCA approved, sold individually.Replaces Ford Part # C8LV-9450-AFits between exhaust manifold and header pipe (H or Y pipe) 2 1/16 id 3 5/8 od cast iron, tapered top and bottom, smooth inside.Note! These are very difficult to seat compared to the pliable ones we sell. If you do decide to use the steel version it is recommended you apply a liberal coating of Permatex High...

Exhaust manifold flange rings or 'doughnuts' for stock cast iron 428CJ exhaust manifolds. These are the malleable type that conform and slightly crush. Inside diameter just over 2-1/8 inches. Sold individually, two needed per car.

This 2 inch dual exhaust system is manufactured right here in the good old USA from an original 1968 J code Cougar. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

This oversized 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from original 1968 Cougars equipped with the 289 or 302 engine. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging...

This 2 inch dual exhaust system is manufactured right here in the good old USA from an original 1968 S code Cougar. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

This oversized 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from original 1967-68 Cougars equipped with the 390 or 427 engine. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached...

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from an original 1969 R code Cougar. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original...

Factory cast iron exhaust manifold set, both right C6OE-9430-E and left C6OE-9431-F side exhaust manifolds. Same manifold for all 289 and 302 engines for both 1967 and 1968. Random date codes.

C6OE-9431-F Factory original cast iron exhaust manifold for driver side. Ford manifold used on all 1967 and 1968 289/302 engines.

C60E-9430-E Factory original cast iron exhaust manifold for passenger side. Factory Ford manifold used in both 1967 and 1968 for all 289 and 302 engines. The heat riser stud will not be broken off like most. If this not a concern to you and want to save money please let us know!NOTE* Item has been sand blasted for pictures. The manifold you will get will be off of a parts car and will need cleaning.

Factory original cast iron exhaust manifold for passenger/right side. For both S & X code 390 engines and W code 427 GT-E engines manufactured after 2/15/1968.Ford part # C8OE-9428-C.

C8OE-9428-A Factory original cast iron exhaust manifold for passenger side. Cast number C8OE-9428-B is also acceptable for 1968. Current manifold has a legible casting date of 5/4/1968. Happy Star Wars day.

Spot on reproductions made of higher quality steel that OEM!

Reproduction high performance cast iron exhaust manifolds for the 1967 - 1968 Cougar or Mustang equipped with the 289 or 302 engine. Designed to be exactly like the originals, with correct markings and raised part numbers. Includes studs and nuts.Replaces Ford part numbers C6OE-9430-E and C6OE-9431-F

390-2V, 390-4V, and 427-4V factory cast iron exhaust manifold set, both a correct right and left set of matching exhaust manifolds. Indicate in the comments section if you want the early 1968 passenger side with C7OE-9428 casting or late 1968 with C8OE-9430 casting.

Exact reproduction of Ford's free-flowing, high-performance cast-iron exhaust manifolds used on the 428 Cobra Jet, 428 Super Cobra Jet, and GT500 Shelby's. Concours correct with original Ford logo and part numbers cast into the manifolds. NOTE: Dwayne from "The Brothers Car Collection" clued us in to the fact that the choke tube fitting on the passenger side is indexed 180 degrees off on some sets we sell. Fortunately you can carefully spin it around with vise grips so the opening faces...

Exact reproduction of Ford's free-flowing, high-performance cast-iron exhaust manifolds used on the 428 Cobra Jet, 428 Super Cobra Jet, and GT500 Shelby's. Concours correct with original Ford logo and part numbers cast into the manifolds. These manifolds are available in both early and late versions. The earlier version manifold has the correct spacer on the right side while the later version manifold does not.  Installs easily and eliminates clearance issues compared to headers....

Excellent reproduction of the 1968 GTE exhaust tips. Correct in every way, these are an exact copy of the originals.

If it were not for the dimples in the top of these rolled tip stainless steel reproductions, they would be visually "spot on" from the rear view once installed! Since the dimpled portion is hidden by the rear valance, this makes for a cost effective replacement option or great for that GT-E clone. Sold as a PAIR. Replaces Ford Part #: C7ZZ-5258-C or C9ZZ-5258-C. *NOTE* If anyone would like to share a picture of an original GT-E tip with the correct "drop down" extension that precedes this tip...

Excellent reproduction of the 1968 Mercury Cougar XR7-G exhaust tips. Copied from an NOS example, these are accurate in every way, even down to the Shelby Ford part number. When these were originally stamped with the part number, they used an upside down "M" for a W in the S8WS-5232-A casting number, as shown in the photo. That is not a typo. Shipped as a pair, we detailed the one in the photo with the black paint to mimic the originals. To help keep costs down, we are unable to put the detail...

These are not concours correct, but still look good. "Pipe within a pipe" chrome plated 14 gauge steel.Replaces Ford part number S8WS-5232-A.

Correct black phosphate bolts for use with 289 HiPo (K-code) exhaust manifolds. Although Cougars never offered a HiPo 289, the HiPo manifolds will fit any 67-68 289 or 302.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds. 390 and 427-4V engines without exhaust heat risers. That kit would include a studded bolt for the heat shield. See item 41282.

This direct replacement H pipe only for any 1967-68 Mercury Cougar or Ford Mustang equipped with either the 289 or 302 engine and stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery. ...

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 289 or 302 engine. We also sell this H pipe in a 2 inch diameter and have OEM style dual exhaust systems...

Direct replacement H pipe only for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds that includes the spacer valve on the passenger side. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 390 or 427 engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail...

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1967-68 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds that includes the spacer valve on the passenger side. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1967 and 1968 Cougars and Mustangs with either the 390 or 427 engine. We also sell this H pipe in a 2 inch...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1968-69 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from original 1968-69 Cougars and Mustangs with the 428CJ engine. We also sell this H pipe in a 2-1/2 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for...

This direct replacement features a larger than stock diameter of 2-1/2 inches for increased performance. This is the H pipe only and is for any 1968-69 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from original 1968-69 Cougars and Mustangs with the 428CJ engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style dual exhaust systems that include the...

Good used hanger used only on dual exhaust cars. Rubber will be in usable condition but showing its age. Mounts to the rear of a 'turbo' style muffler. 302, 390, 427, 428CJ - all with dual exhausts. Ford part number C8WY-5260-F. *Later production cars, after 11-1-1967

Good used hanger with detail you will never find in a reproduction part. The part you will receive has not been blasted. Mounts to the rear of a 'turbo' style muffler. Right side bracket. 302, 390, 427, 428CJ - all with dual exhausts. Ford part number C8WY-5260-G. *Later production cars, after 11-1-1967

Good used tail pipe hanger with decent rubber still attached. Mounts to the frame on the right side of the fuel tank. Supports and holds the rear of the tailpipe stationary. All 1968 - 1970 dual and single exhaust Cougars, all engines. 1970 differs in that the tail pipe clamp was spot welded to the hanger. When you look closely on the 1970 version you will see that there is an alignment hole in the bracket and an alignment tab on the clamp. Also the 1970 version had a less pronounced gusset at...

Mounts to the rear of a 'turbo' style muffler. Right side bracket. 289, 302, 390, 427, 428 all with dual exhausts. Ford part number C8WY-5260-D. *Early production prior to 11-1-1967

Mounts behind the muffler on the passenger side of the drive shaft. Ford part number C8WY-5260-C. *Early production prior to 11-1-1967

Mounts behind the muffler on the passenger side of the drive shaft. Ford part number C8WY-5260-H. *Later production after 11-1-1967

This set consists of one tail pipe hanger and one muffler hanger, both were mounted on the passenger side of the car. The only cars eligible for single exhaust in 1968 were the C code 289 2V and the F code 302 2V, single exhaust never came on 1968 big block Cougars. In some instances 2 barrel cars had special ordered dual exhaust as an option from the factory. Probably the most common occurrence would be those few F code 302-2V engines installed in the ultra rare, ultra cool XR7-G. *Early...