Body

Reproduction "A" pillar repair panels for your 67 - 68 Cougar or Mustang. Included in this kit are the two pillar patches and four backing plates for the door hinges.

Hex head screw for attaching floor drain hole covers. Several different screws were used over the years and at different plants. All seem to be a #8 sheet metal screw of varying lengths. This is a #8 hex washer head tapping screw with 5/8" length. Two screws per drain cover, 2 or 4? per car, not sure. We also have the drain covers. 

Reproduction driver side inner A pillar inner / kick panel for the 67 - 68 Cougar or Mustang.

Reproduction passenger side inner A pillar inner / kick panel for the 67 - 68 Cougar or Mustang.

Ford called this small door latch part an adjuster. It threads onto the bottom of the door latch rod inside the door. Common to most Ford products 1965-1970. Ford part number C5AZ-62218106-A.

This knurled nut is located under the front slides in each corner (1 per side, 2 per car) and is used to adjust the height of the sun roof panel.

This plate is what is located on the backside of your door jam where your striker threads in one. Two threaded holes for attaching the striker plates on any 1967-70 Mercury Cougar or Ford Mustang. Right and left are the same. 

These keep the trunk hinge spring rods from rattling. These are a reproduction of the anti-rattler for 67-68 Cougar / 65-68 Mustang.   Replaces Ford part # C5ZZ-6545028. These also work for the 69-70 Cougar / Mustang better than what came factory, which, according to the Ford MPC, for 69-70 would have actually been 1/8" x 7/8" Vinyl Foam Weatherstrip Tape, Ford part C6AZ-19627-A. Check out our trunk torsion bar installation video: ...

Reproduction driver side (left hand) rear apron extension for 1967 - 1968 Mercury Cougar and Ford Mustang. These plates almost always get destroyed when installing new aprons, so don't forget to grab one for each side you work on.

Reproduction passenger side (right hand) rear apron extension for the 1967 - 1968 Mercury Cougar and Ford Mustang. These plates almost always get destroyed when installing new aprons, so don't forget to grab one for each side you work on.

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford part # C8ZZ-6524100 and C8ZZ-6524101. *NOTE* The Ivy Gold and Aqua armrests...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford part # C8ZZ-6524100 and C8ZZ-6524101. *NOTE* The Ivy Gold and Aqua armrests...

Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard Cougar's. We also have NOS and used available in most colors. I know it will cost us sales by being blunt about the quality on some of these items, but after using these...

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # C8ZZ-6524100-BK.

Unlike the light blue found on a Cougar this is the darker blue used on the 1968 Mustang. The light blue is not available. This is a good match to the darker blue accents found on the 1968 standard and decor Cougar interior. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard Cougar's. We also have NOS and used available in most colors. I know it will cost us sales by being...

Unlike the light blue found on a Cougar this is the darker blue used on the 1968 Mustang. The light blue is not available. This is a good match to the darker blue accents found on the 1968 standard and decor Cougar interior. Color on these is inconsistent and never spot on to the original. No returns on this item.

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford part # C8ZZ-6524100 and C8ZZ-6524101. *NOTE* The Ivy Gold and Aqua...

Reproduction passenger / right side armrest for the 68 Cougar. Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford part...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford part # C8ZZ-6524100 and C8ZZ-6524101. Color on these is inconsistent...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue, Parchment, Ivy Gold, Aqua, Saddle, or Nugget Gold. Replaces Ford Part #: C8ZZ-6524100 and C8ZZ-6524101. *NOTE* The Ivy Gold and Aqua armrests are not correctly colored...

Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard Cougar's. We also have NOS and used available in most colors. I know it will cost us sales by being blunt about the quality on some of these items, but after using these...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford Part #: C8ZZ-6524100 and C8ZZ-6524101. ...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford Part #: C8ZZ-6524100 and C8ZZ-6524101 Color on these is inconsistent...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford Part #: C8ZZ-6524100 and C8ZZ-6524101 *NOTE* The Ivy Gold and Aqua...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used available. Available in Black, Dark Red, Blue (not shown), Parchment, Ivy Gold, Aqua (not shown), Saddle, or Nugget Gold (not shown). Replaces Ford part # C8ZZ-6524100 and C8ZZ-6524101. *NOTE* The Ivy Gold and Aqua...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7.  Color on these is inconsistent and never spot on to the original.

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not concours like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not concours like the XR7 but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7 but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Driver side rear arm rest for 1967-68 Mercury Cougar. File photo shows a passenger side arm rest, this is a driver side Grade "B" rear interior armrest. Grade "B" armrests are pulling away from their backing but have no splits, cigarette burns or other obvious defects. They probably need to be painted with vinyl paint, especially since we can "almost" guarantee we will not have both sides of "your" color in stock. Please indicate which color you would prefer and we will do our best to...

Passenger side rear arm rest for 1967-68 Mercury Cougar. Grade "B" rear interior armrest. Grade "B" armrests are pulling away from their backing but have no splits, cigarette burns or other obvious defects. They probably need to be painted with vinyl paint, especially since we can "almost" guarantee we will not have both sides of "your" color in stock. Please indicate which color you would prefer and we will do our best to accommodate you. The downfall of a "B" armrest is that it will show an...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...