Exhaust

This set consists of one tail pipe hanger and one muffler hanger, both were mounted on the passenger side of the car. The only cars eligible for single exhaust in 1968 were the C code 289 2V and the F code 302 2V, single exhaust never came on 1968 big block Cougars. *Later production after 11-1-1967

Reproduction Concours Correct muffler hangers for your 1968 - 1970 Mercury Cougar.

Muffler mounting tabs for using factory Ford muffler hangers on aftermarket turbo style exhaust mufflers. These help achieve that concours look using a replacement muffler or mufflers. We recommend using your existing horse shoe shaped muffler hanger as a jig for locating these tabs prior to welding. These were copied from the original style tabs found on most 1968-73 Mercury Cougar and Ford Mustangs. 1967 cars and some Mustangs used a single transverse muffler behind the rear axles, these may...

Very rare one year only heat riser "S" shaped metal tube that attaches to the heat shield on the passenger side front portion of the exhaust manifold. Correct for all 1968 Cougars equipped with the 390 cubic inch engine.Ford part number C8AZ-9652-A.

*NOTE: This item comes un-painted from the manufacturer.Very correct reproduction of an impossible to find part. The only difference I can detect is that this original weighs just an ounce or two more than the original. Click on images to enlarge. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the...

C8AZ-9A603-C metal shroud and tube assembly that attaches to the factory 1968 air cleaner assembly on all C code 289-2V engines as well as F code 302-2V, and J code 302-4V engines all for 1968. We do not believe that this set up came with the Canadian export Cougars, those 1968 Cougars should have the closed PCV system, much like the 1967 49 state Cougars.Do to age and their location our used risers will have minor surface rust, but otherwise be in good condition. Reproduction version of this...

C8AZ-9A603-C metal shroud and tube assembly that attaches to the factory 1968 air cleaner assembly on all C code 289-2V engines as well as F code 302-2V, and J code 302-4V engines all for 1968. We do not believe that this set up came with the Canadian export Cougars, those 1968 Cougars should have the closed PCV system, much like the 1967 49 state Cougars.Do to age and their location our used risers will have rust and or be very thin in spots. Reproduction version of this part is no longer...

Very hard to find, one year only part that is not currently reproduced. These came on 1968 Cougars equipped with the "S" code 390 and the "X" code 390. Must have for that show quality GT or XR7-G. *NOTE* Please keep in mind that our hard to find parts like this are not always competitively priced with what you will find on the open market at swap meets and private party sales. Our primary intent in listing these is for our customers to use this website as a resource to properly identify parts...

*NOTE: This item comes un-painted from the manufacturer.Another spot on reproduction! Correct for CJ and SCJ.  Comes with brackets and hardware as shown. Click on images to enlarge. ...

Sold individually Zinc (Dark Silver)

Reproduction hex screw for exhaust pipe clamps for the 1967 - 1973 Mercury Cougar and Ford Mustang. 5/16 x 1-1/2 screw. Fits original and new clamps.

Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.

Reproduction Exhaust Manifold Pipe Stud Kit for the 260, 289, 302, 351 and 1969 390GT 1967 - 1972 Mercury Cougar and Ford Mustang

Kit has the longer studs for use with spacers or butterfly spacers, between 390 and 428CJ passenger side exhaust manifolds and H pipe flange.

This rear segment exhaust system is manufactured right here in the good old USA from original 1968 and 1969 Mercury Cougars. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

This 2-1/4 rear segment exhaust system is manufactured right here in the good old USA from an original 1969 R code Cougar. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

Reproduction 428 Cobra Jet Exhaust Manifold Spacer 1968 - 1970 Mercury Cougar, Ford Mustang, Shelby and Torino Repro

Used exhaust manifold spacer without butterfly valve for use on 1967 to mid 1968 Mercury Cougar, Mercury Cyclone, Ford Fairlane, and Ford Mustang with 390 or 427-4V engines. Straight factory used spacer. Most cars came equipped with a thermal spacer that often times gets frozen with time. No obstruction with this one.Note - Does not fit the slightly larger 428CJ exhaust manifolds. Ford part number C6OZ-9A427.

Used exhaust manifold spacer with butterfly valve for use on 1967 to mid 1968 Mercury Cougar, Mercury Cyclone, Ford Fairlane, and Ford Mustang with 390 or 427-4V engines. Fully functional, we test these with a heat gun, they do open and close. These thermostat control valve assembly mates to the 1967 and 1968 passenger side 390 exhaust manifold up until about Feb 15, 1968. Easy to tell if it is needed with your manifold, no chamfer for the exhaust donuts at collector? you need this or a...

Stud for attaching heat shield to passenger side exhaust manifold. Fits all 1968 Mercury Cougar or Ford Mustang and other Ford too. Sold individually. Phosphate & Oil (gray-black)

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the longer of the two stud bolts. See item 41350 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 382803-S

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the shorter of the two stud bolts. See item 31171 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 

OEM Style Universal Exhaust Hanger Bracket 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

Band or ring style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Comes with a course sheet metal type hex head bolt. Ford part number C6AA-5A272-A. *Not all 1969 & 1970 Cougars had 2-1/4 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C5DA-5A272-B is the factory style 2" tailpipe clamp.

This is a rare find... This used 4 piece bracket set was taken from a June 17th built 1968 390 X code Cougar with factory dual exhaust. These are much cleaner used parts than you will see in other regions as they have never been exposed to road salt. We no longer sell them with the bolts and clamps, this is a sample photo of one of several sets we have in stock as of 10-12-07. The parts you receive may actually be in better condition except for the rubber parts which are often worse. The...

C7OE-9431-A Factory original cast iron exhaust manifold for driver side. 1967, 1968, and 1969 390/427 left side manifold remained unchanged for all three years. Includes 1968 X code 390-2V Premium fuel cars. Click on images to enlarge. ...

Factory original cast iron exhaust manifold for the passenger/right side and is probably a mid-year change for 1967. For both S & X code 390 engines and W code 427 GT-E engines up until 2/15/1968. Butterfly spacer not included. Ford part # C7OE-9430-C.

C8OE-9431-A Factory original cast iron exhaust manifold for driver side.

Used pair of Exhaust Manifolds / 428CJ for the 1968 Mercury Cougar / 1968 Ford Mustang 

This is the harder to find tail pipe hanger as it was only used on dual exhaust cars. Will have usable but cracked rubber. Mounts to the frame on the left side of the fuel tank. Supports and holds the rear of the tailpipe stationary. All 1968 - 1969 dual exhaust Cougars, all engines. Ford part number C8WY-5260-B.

Mounts to the rear of a 'turbo' style muffler. Left side bracket. 289, 302, 390, 427, 428, all with dual exhausts. Ford part number C8WY-5260-E. *Early production prior to 11-1-1967

Used original heat riser / S tube for 1968, 1969, and 1970 Cougar and Mustang 428 Cobra Jet / Super Cobra Jet. These will seldom be available. The one pictured above is the best example we've ever seen - removed from the car in 1969 just days after purchase. The pictures below are a more realistic example of the used condition you might expect. There are also additional comparison shots next to the reproduction S tube we also sell. The differences are small but the most obvious is the fact...

C8OZ-9A603-B metal shroud that attaches to the passenger side stock cast iron exhaust manifold. Works in conjunction with a metal 'S' tube sold separately (C8AZ-9652-A). R code and Q code Cobra Jet engines only.

Reproduction intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

Used intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

OEM Style Transverse Resonator Exhaust Hanger 1967, 1968 and 1969 Mercury Cougar and Ford Mustang