1968 Mercury Cougar

Reproduction bolts and washers for the manual transmission bell housing on any 1967-68 Cougar or Mustang equipped with a 289 / 302 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1967-68.

Reproduction bolts and washers for the manual transmission bell housing on any 67 - until 2/1968 Cougar or Mustang equipped with a 390 / 428.

Reproduction bolts and washers for the manual transmission bell housing on mid , like Feb 1968 - 1970 Cougar or Mustang or other Ford car equipped with a 390 / 428 engines. Bell housing to engine block bolts.

Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold as a set of 4. Concours phosphate & Oil (gray-black).

Concours bolt set for all 1968-70 Mercury Cougar and Ford products including Mustang, radiator fan clutch to radiator cooling fan. 1/2 inch hex head size. Threads are 5/16-18. Four bolts with captured split washers. Also sold individually. ...

Concours bolt set for all 1968-70 Mercury Cougar and Ford products including Mustang radiator fan clutch to water pump. 1/2 inch hex head size. Threads are 5/16-24. Also sold individually. These bolts have an approximate length of 7/8" to the shoulder and an approximate overall length of 1-1/8". ...

These reproduction fender to pillar bracket bolts fit both the Standard and XR7.

Reproduction pair of 1 1/8" long hood latch support bolts for the 1968 Mercury Cougar. Looking through cars with original parts, we've found a few different variations of the types of bolts used. It would be best to measure what you have and purchase the correct length bolts.

These reproduction hood latch catch bolts fit both the Standard and XR7.

Reproduction pair of 7/8" long hood latch support bolts for the 1968 Mercury Cougar. Looking through cars with original parts, we've found a few different variations of the types of bolts used. It would be best to measure what you have and purchase the correct length bolts.

Reproduction set of idler arm bolts for the 1967 - 1968 Cougar or Mustang.

New set of bolts for fastening the transmission inspection cover on all 1967-70 Mercury Cougar, Ford Mustang, and Ford anything with 390, 428CJ, and 352 or any FE style Ford engine. Includes 3 and 4 speed transmissions.

Pair (2) Bolts for securing the inspection cover for any C-4 automatic transmission 1967-68 Mercury Cougar or 1965-70 Ford Mustang. Additionally also fits FMX transmissions 1969-73 Mercury Cougar.or Ford Mustang.

4 Bolts for securing the inspection cover for any C-6 automatic transmission 1967-70 Mercury Cougar or Ford Mustang.

Reproduction bolts for the deck/trunk lid latch for the Mercury Cougar or Ford Mustang. This is a set of five bolts and will fit both the standard and XR7. Total of 5 bolts used 1969-73, 1967-68 Cougars will only use 2. We think that Mustangs use 5 on all years 1967-73.AMK F-227 ...

Leaf spring front bolts for any 1968 Mercury Cougar or Ford Mustang. AMK F-368, About 4-3/8 inches long. 4 total pieces, 2 bolts, 2 nuts.

Fits all models.

Pictured is a complete set of 1967 Hex bolts, spacers and washers. We will make sure they are damage free, rust free, and a complete set removed from the same year of Cougar as yours. There were minor and major changes almost every year so you will want to select the right year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! 

Bolt kit for mounting power steering ram cylinder brackets to the frame rail on any 1967-70 Mercury Cougar or Ford Mustang. Kit includes: two short bolts with lock washers, long horizontal bolt, nut, and reinforcing washer. Quality AMK fastener kit.

Installation kit for the fastening the new reproduction deck lids to the trunk hinges on the 67 - 70 Mercury Cougar. The reproduction deck lids don't come with the J nuts installed and we've found this set to be a perfect fit.

New bolts and nuts for attaching the engine frame stands to the frame. Fits all 1967-70 Mercury Cougar and Ford Mustang with V8 engines. 4 bolts and 4 nuts. 3/8-16 X 3 1/2 Grade 5 phosphate flange bolts.

Engine mount bolt kit for installing engine or motor mounts to the frame stands. 1967-70 Mercury Cougar or Ford Mustang V-8. Two bolts and two nuts. Quality AMK part F-753.

Here are our reproduction hood latch support brace bolts and U nuts for the Mercury Cougar.

These pamphlets were found buried in the back room of a San Jose California Lincoln-Mercury dealership. There was no reason to keep them after the warranty expired so most were discarded long ago. Great for that person who likes original documents. Limited quantity.

New rubber boot for brake push rod to the master cylinder on all drum brake cars. Fits all 1967-72 Mercury Cougar and 1965-73 Ford anything cars, including Mustang.Trivia - Did you know that 100% of all 1973 Mercury Cougars, came from the factory with front power disc brakes?

Reproduction rubber boot for the drag link end of the power steering ram cylinder on most any 1967-70 Ford small and intermediate sized cars. Comes with band style crimp clamp like the originals. Keep in mind that this product is made from material that is thinner and softer than OEM.

Reproduction power steering control valve boot and clamp, for the 1967-70 Mercury Cougar or 1965-70 Ford Mustang. Gold tone clamp, molded rubber boot, and pair of screws. Very accurate reproduction. 

Holley fuel filter decal, for Holley equipped cars. Including all 1967-68 S code 390-4V, 1968-70 R and Q code 428 Cobra Jets, 1967 GT-E with W code 427-4V, or 1969-70 G code Boss 302 Eliminators. Concours detail item. C7OE-9155-A. 

Sold as pair on exchange or outright. Only cores with minimal corrosion can be considered for exchange. Ford part number C7AZ-6204144-A, casting number as seen on the backside reads C8AB-6204122-B.  Does not include smaller rod for the sun visor tips.  Sold as a pair.

Reproduction Sun Visor Bracket & Rod for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang. Great quality and fit, left and right use same part, sold separately. Replaces Ford part # C7AZ-6204144-A.

Used mounting bracket from a 1967-68 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. 

Used bracket or mounting tab that often gets lost when servicing the air conditioning plenum. Attaches to the box with two screws and has stud that goes through the engine firewall for mounting the A/C box assembly under the dash. Basically the same part as found on 1969-70 brackets, but this one has a slightly shorter and pointed stud. Replaces Ford part number C7ZZ-18A456-A.

9 inch rear axle snubber for all 1968-73 Mercury Cougar and Ford Mustang. Will work on 1967 9" differential but has slightly different angles as seen by our pictures. Bare bracket, rubber snubber sold separately.

Billet aluminum batter hold down bracket for all 1967-70 Mercury Cougar and Ford Mustangs. Maximum battery width 6-3/4 inches. We also have stainless steel hold down bolts available.

Bracket tack welded in the trunk to reinforce the rear structure for mounting the rear bumper. Ford part number C7ZZ-17B862-A, fits all 1967-68 Mercury Cougar and Ford Mustang. These are sold individually, these are not side specific. There is also a reproduction version available. Used part cut from a 1967-68 Mercury Cougar, some spot welds will need to be drilled out on your end. Picture shows approximately what you will receive. 

Used cigar / cigarette lighter and ashtray mounting bracket. Mounts behind the dash on 1967-68 Mercury Cougar and Ford Mustang. Holds the cigar or cigarette lighter element, and the ashtray receptacle. 

These courtesy light brackets are located on the very outer right and left under the dash. Typically this bracket is found on the passenger side of 1967-68 Mercury Cougar and Ford Mustang without air conditioning. This is the long style bracket. There is also a short style for both the driver and passenger side courtesy light. If you have factory air conditioning you would want the short bracket that doesn't come into contact with the A/C plenum.Replaces Ford part number C7ZB-13763-A.Fits:1967...

These courtesy light brackets are located on the very outer right and left under the dash. Typically this bracket is found on the driver side of all 1967-68 Mercury Cougar and Ford Mustang. It is also used on the passenger side if you have air conditioning. This is the short style bracket. There is also a long style for both the passenger side courtesy light if you don't have factory air conditioning. If you have factory air conditioning you would want the short bracket that doesn't come into...

Used bracket for mounting the front valance on any 1967-68 Mercury Cougar. L shaped bracket connects the lower valance, stone guard, and inner bumper bracket. Two per car, sold individually.Ford part number C7WB-17A986.

This is used on Mercury Cougars and Ford Mustangs equipped with factory A/C. This is the bracket for the valve that stops the flow of warm coolant when A/C is turned on. This is an exact reproduction and has the zinc dichromate finish.

This bracket clamps the liquid fitting on the liquid hose to the discharge hose on the inside of the radiator support. It's purpose is to keep the lines from moving around during operation.

Used front license plate bracket in Grade A condition. Grade A will only need detailing or a fresh spray of chassis black paint. We include fasteners to attach the license plate to this bracket. This bracket mounts to your front valance. Also available in Grade B condition, see related items below. Replaces Ford part number C7WY-17736-A.

Used front license plate bracket in Grade B condition. Grade B is relatively flat, in most cases it will be slightly bent from prior use. May have cosmetic issues like multiple layers of paint or slight surface rust. We include fasteners to attach the license plate to this bracket. This bracket mounts to your front valance. Also available in Grade A condition, see related items below.Replaces Ford part number C7WY-17736-A.

One year only bracket used on both fixed and tilt column cars.

Used bracket for mounting the bottom of the quarter window guide to the car body. Fits all 1967-68 Mercury Cougar and 1966-68 Ford Mustang coupe and convertible (non fastback). "L" shaped bracket that designed for mounting and adjusting the rear quarter window.Replaces Ford part number C6ZB-6529778.

Bare metal power steering hose bracket for any 1967-69 small block Mercury Cougar or Ford Mustang. 289-2V, 289-4V, 302-2V, 302-4V, 351-2V, and 351-4V. No rubber insulator included.

For any 1967 or 1968 Cougar with either a 289 or 302 engine. Virtually the same bracket as for the 1969 351W engine. Except for the obvious 1-1/4 inch hole in the middle of the bracket, they are the same. Compare the OEM used part price to the reproduction part. Ford master part number C7AZ-3C511-A, same part number as the 351W bracket with the addition of the large hole. Ford intended to have a casting number stamped on these brackets and it would have been C7AA-3C511-B. For restoration...

Perfect fit for use with AC or non-AC 67, 68, 69, or 70 Cougar with the 390, 427, or 428 big block.