1968 Mercury Cougar

New front outer wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.75 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...

Reproduction steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. Outside diameter: 1 1/2" Inside diameter: 1 1/4"*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used lower steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. The upper bearing can be found here. Outside diameter: 1.500"Inside diameter: 1.060" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction of the upper steering column bearing for your 67* - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. You can find the lower bearing here. Outside diameter: 1 3/16 " Inside diameter: 15/16 "Thickness: 1/4" Replaces Ford Part Numbers: F23Z-3517, C1AA-3517-A, C3AZ-3517-A, C7SZ-3517-D, D0AZ-3517-A, F23Z-3517-B * - may not fit some 67 Mustang applications with a fixed column as these used Ford...

NOS long shaft bearing for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180".  Shaft length (sticking out of bearing) 1 1/8" Ford numbers C4AZ-2990-A, C4AA-2A898-A. Check out this video ...

Repair your own idler / tensioner with our bearing for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180".  Shaft length (sticking out of bearing) 1 1/8" Overall length 2-3/4" Ford numbers C4AZ-2990-A, C4AA-2A898-A. Check out this video ...

Repair your own idler / tensioner with our kit which includes a dust cover and is for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180".  We have had a machinist shorten the shaft on these bearings so that they are easily pressed into the cast pulley brackets that use the short...

C5OP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1967 - 1968 Mercury Cougar with any 289 or 302 engine and automatic C4 transmission, code W on your door tag. 1967 - 1972 Ford Mustang with 250, 289, or 302 engine and automatic C4 transmission, code W on your door data plate.  Fits the 157 tooth flex plates. There was a 164 tooth flex plate that came later. Ford master part number C5OZ-7976-A. . ...

Reproduction bellows and clamp for your 67 - 69 Cougar or Mustang Midland power brake booster.

NOTE: At the moment the supplier is only making the late model version of this beltline kit. The late version has a slight bend in the chromed quarter piece, whereas the early version is straight (see photo above). Made With Exact Materials As Original. Eight piece kit that includes inner and outer belt-line, enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them...

Grade A used A/C center vent for XR7 (non Standard) model Cougars. These will have some minor chrome blemishe in the plating, but no heavy pitting or damage. Fits the XR7 model (65B) Cougars with woodgrain dash faces. See our other listing for Grade B versions of this air conditioning center register or vent. *Note - Will not fit Standard model Cougars. Replaces Ford number C7WY-19893-D.

Reproduction A/C center vent for XR7 (non Standard) model Cougars. These are great quality vents with bright chrome finish. Fits the XR7 model (65B) Cougars with woodgrain dash faces. *Note - Will not fit Standard model Cougars. Replaces Ford number C7WY-19893-D.

Grade A used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Very minor blemishes, almost insignificant as shown. No extra parts included, levers and switches available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19A976-F Register and Control assy. (Bright Finish). Bright finish is Cougar, Ford Mustang bezels had black pebble grain or wood grain finishes attached. Ford casting number on...

Grade B used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Some blemishes as shown. No extra parts included, levers and switches available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19A976-F Register and Control assy. (Bright Finish). Bright finish is Cougar, Ford Mustang bezels had black pebble grain or wood grain finishes attached. Ford casting number on reverse of this piece is...

Grade A used A/C center vent for standard (non XR7) model Cougars. These will have almost perfect chrome plating, minor blemishes only, no major pitting. Fits the standard model (65A or 65C) Cougars with padded dash face pads. See our other listing for Grade B versions of this air conditioning center register or vent.*Note - Will not fit XR7 model Cougars.Replaces Ford casting number C7WA-19623 and C7WY-19893-A.

Grade B used A/C center vent for standard (non XR7) model Cougars. These will have some defective chrome plating, and pitting. Fits the standard model (65A or 65C) Cougars with padded dash face pads. See our other listing for Grade A versions of this air conditioning center register or vent.*Note - Will not fit XR7 model Cougars.Replaces Ford casting number C7WA-19623 and C7WY-19893-A.

Reproduction A/C center vent for standard (non XR7) model Cougars. These are great quality vents with bright chrome finish. Fits the standard model (65A or 65C) Cougars with padded dash face pads. *Plastic chrome vent plate included.*Note - Will not fit XR7 model Cougars.Replaces Ford casting number C7WA-19623 and C7WY-19893-A.

Grade B used A/C center vent for XR7 (non Standard) model Cougars. These will have some defective chrome plating, and pitting. Fits the XR7 model (65B) Cougars with woodgrain dash faces. See our other listing for Grade A versions of this air conditioning center register or vent. *Note - Will not fit Standard model Cougars. Replaces Ford number C7WY-19893-D.

Emergency flasher switch bezel for the side of fixed steering columns (non-tilt). For all years 1967 1968 1969. Paint to match your interior. There is a slight difference between the original bezel and these reproductions. Original bezels have taller "Emergency Flasher" lettering, plus they came color matched to the steering columns. Functional reproduction item. Ford part number C9OZ-15C580-A.

Emergency flasher switch bezel for the side of fixed steering columns (non-tilt). For all years 1967 1968 1969. Paint to match your interior. Compared to the reproduction version of this bezel, there is a difference. "Emergency Flasher" lettering is much heavier on the originals, plus they came color matched to the steering columns. We can often times supply your desired color, please include color needs in the comments section. Ford part number C9OZ-15C580-A.

Emergency flasher bezel for the side of the tilt steering column. Reproduction bezel in black. Replaces most all tilt swing steering columns from 1967-69. Replaces Ford part number C9AZ-15C80-A, and an earlier part number starting that was likely C7SZ-15C580-A.

Nice reproduction globe box door button bezel for all 1967-70 Mercury Cougar and Ford Mustangs. We do sell used to, see related.Replaces Ford part number C6OB-62060A12.

This trim ring that surrounds the glove box release button is often missing. Easily installs by snapping in place. Better fit than the reproductions out there.Replaces Ford part number C6OB-62060A12.

Driver side headlight door. If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The four Phillips...

Driver side headlight door. New Old Stock.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The...

Passenger side headlight door.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the passenger side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13052 for the passenger side and C7WB-13064 for the driver side. The four...

Quality reproduction to replace your pitted original. Replaces Ford Part #: C7ZZ-10852-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Incorrect chrome finish (supposed to be satin not chrome) Mustang part that requires modification to make the metal XR7 insert fit. This is the only new alternative to your broken bezel, we sometimes get in an original that just needs paint. This unit will also fit the Cyclone, Montego, and many other Mercurys and Fords. Replaces Ford part # C8ZZ-3D572-A.

This is the correct horn panel bezel for all 1968 standard model Cougar steering wheels. The satin paint will need to be resprayed but the two mounting studs are in place and there are no cracks or burns. Please see related for XR7 model bezel. Ford part number C8AA-3D754-A.

This is the correct horn panel bezel for all 1968 Cougar XR7 steering wheels. The satin paint will need to be resprayed but the two mounting studs are in place and there are no cracks or burns. Unique to the XR7, identified by having the grey inserts. Please see related for standard model bezel.Ford part number C8AA-3D754-A. * Note - Will not work on standard model Cougar pads without removal of the inserts.

Inexpensive upgrade, replaces that bezel damaged by improper screw driver removal. We also sell the special tool that removes this without hassle or damage

Used ignition lock cylinder bezel for any 1967-68 Mercury Cougar, ford Mustang and likely Fairlane / Comet. Good used condition, we recycle the pitted crusty ones. Half the price of the repop version. We also sell the special tool that removes this without hassle or damage.Replaces Ford part number C6OZ-11584-A.

Used radio bezel that will show minor pitting and will most likely need the black area repainted. For use on cars with no console. Two different castings, need to be side by side to see minor difference. Ford part # C8ZA-18842 and C7ZA-18842.

This radio bezel is made by the original Ford supplier and features high quality die cast chrome. For cars without a center console. Replaces Ford Part #:C8ZA-18842-C.

This bezel is covered almost entirely by the face pad with clock. Only the small area around the radio actually shows once installed. This late bezel does not have the upper support, the early version is closed. Keep in mind that this grade "B" bezel will likely have one of the tabs broken or modified for an aftermarket stereo.Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a storage compartment. The slide up doors...

Both our A and B quality bezels will need a replacement brushed aluminum overlay. This used bezel will have no broken or missing parts. Most likely the white will be missing from the P R N D 2 1. We also have grade "B" used units with minor flaws for less than half the price. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand...

Both our A and B quality bezels will need the overlay replaced. Cosmetically this bezel will be as good as our grade "A" units, but when you turn them over you will notice one or two of the feet will be broken off. These missing feet may make it a little more cumbersome to install and if someone walks on your installed console these feet do provide support. Obviously it would be easy to glue on some feet (or spacers) but this item will install just fine without them. Most likely the white will...

This shift indicator will work on a 1967 or 1968 Cougar or Mustang equipped with automatic transmission. It comes with all items shown here.

Used shifter plate bezel for the Mercury Cougar or Ford Mustang equipped with a 3 or 4 speed manual transmission, but without a center console. This unit is a nice upgrade from the simple plain Mustang boot retainer. This version is the one held down with no screws, the rubber boot holds it in place. Part number C7WB-7262-D is the one being sold.Ford part # three different casting numbers with very slight variations. C7WB-7262-A, C7WB-7262-C, & C7WB-7262-D. Check out our video on...

There are two of these rings on the driver side cluster. One outlines the tachometer and one outlines the speedometer. Sold individually, two per car.

There are three of these small rings on your cluster that outline the amp, temperature and fuel gauges. The oil pressure gauge is unique in that the decorative black ring is incorporated into the gauge housing.Sold individually, three per car.

These are 100% correct reproductions for the 1968 Mercury Cougar XR7-G, but will fit any 1967-68 Cougar. These will NOT lay flat against the valance, as the originals did not. These are beveled on purpose and if you attempt to straighten them they WILL break. The reproductions that do lay flat against the valance are no longer being produced. We cannot warranty these against any attempts to straighten them. Sold as a pair. ...

Bleeder screw for your 1968 - 1973 Cougar or Mustang Calipers.

A scratch obtained during shipping, an irregularity in the anodized plating process, a ding in a hard to reach spot that did not come out 100%, a slip on the buffer wheel or a pin hole created by over polishing are what you can expect on a blemished piece of trim. We try to carefully examine every trim part that comes back from our restorer for the smallest of imperfections. If we would not place them on our $40,000.00 Cougar we do not expect you to... From 10-15 feet away these will look good...

A scratch obtained during shipping, an irregularity in the anodized plating process, a ding in a hard to reach spot that did not come out 100%, a slip on the buffer wheel or a pin hole created by over polishing are what you can expect on a blemished piece of trim. We try to carefully examine every trim part that comes back from our restorer for the smallest of imperfections. If we would not place them on our $40,000.00 Cougar we do not expect you to... From 10-15 feet away these will look good...

Used in 1967 - 1968 standard model Cougars without the optional clock. Usually these will have some amount of fading or minor discoloration in the paint as we keep the mint ones to build tachometers from.Check out the video below on our new gauge tester: ...

Used heater blower motor for very late 1967 and all 1968 Mercury Cougars and Ford Mustangs with integral or factory air conditioning. The tell tale sign is the early motors have a nipple of attaching the rubber elbow. This later version has a round hole for attaching a different rubber elbow. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting...

Used heater blower motor for 1967 Mercury Cougars and Ford Mustangs with integral or factory air conditioning. The tell tale sign is the early motors have a nipple of attaching the rubber elbow. Later version has a round hole for attaching a different rubber elbow. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is also included. On...