1968 Mercury Cougar

Left side axle, 28 spline 27-1/16 inch length. For both 8 inch and 9 inch rear ends. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs.*Note Boss 302 and 428 CJ equipped Cougars came with heavy duty 31 splined axles.

Right side axle, 28 spline 31-1/8 inch length. For both 8 inch and 9 inch rear ends. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note Boss 302 and 428 CJ equipped Cougars came with heavy duty 31 splined axles.

Bare housing with proper axle pad spacing for all 1967-1968 Cougars with 289 or 302 engines. Over-sized shipping length. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. This axle housing was used starting about mid 1967. It does not have the fill plug in the rear of the housing. * Important - Please check your car to verify that your 8 inch third member has a fill plug. Replaces Ford part number C7ZZ-4010-E. ...

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Axles used: Passenger side - 31-1/8 inches long, Driver side 27 inches long. Complete rear end housing - drum to drum, with axles, and with pumpkin. For...

OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S

Used pair of 31 spline axles for the 68 - 70 Cougar or Mustang, equipped with the Boss 302, 427 and 428 CJ engines all with 9 inch rear axles. Most all other vehicles used 28 spline axles. Short axle 27-1/16" inches long and long axle 31-1/8" inches long. Ford part numbers C9OZ-4234-C and C9OZ-4234-D. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. ...

This lens comes without the correct FoMoCo logo, sold individually. Replaces Ford Part # C5ZZ-15514.

These Back Up Light Lens Gaskets are sold as a pair. Fits the 67 and the 68. Replaces Ford part # C5ZZ-15510.

The correct color for the Cougar was gray but many prefer these black Mustang gaskets. Sold as a pair.

These Back Up Light To Rear Valance Seals are Sold as a pair. Fits the 67 and the 68. Replaces Ford part #: C7ZZ-15533. Note, gray is in fact the correct color for these, Mustang used black in 67-68. Note we also have black available for those who prefer.

These Back-Up Lamp Lenses are exact copies of the originals which come with the FoMoCo Logo. Sold Individually. Includes screws!

Sold individually. Stainless Steel

Don't throw away those panels just because the backing boards are broken and warped! You cannot buy reproduction panels for the 67-70 Mercury Cougar, but you can get this pair of backer boards. If your vinyl is good, then you will want to put the work into them. These are not a quick fix, they do take time to install but the end result is worth it. These will work on your 67-68 XR7, Decor or Standard model as they are cut for all models and all options (i.e. manual remote mirror, courtesy...

This kit is a time and money saver. Quality chrome bezels and all related parts are included. This is a direct plug-in, no modifications needed.

Hassle free kit makes it easy to install backup lamps. This kit includes mounting pads, lenses, gaskets, T1142 Bulbs and mounting hardware.

Great chrome on this reproduction backup / reverse light for the driver side (left hand) of the Mercury Cougar or Ford Mustang. Lens, gasket, and bulb sold separately. Replaces Ford part # C7ZZ-15512.

Used backup / reverse light for the driver side (left hand) of the Mercury Cougar and Ford Mustang. Lens, gasket, and bulb sold separately, but we do have a kit available. These used lights will often have a minimal amount of pitting on the inside close up to the lens. Casting number as seen on the back side reads C7ZB-15A509-A. Replaces Ford part # C7ZZ-15512.

Great chrome on this reproduction backup / reverse light for the passenger side (right hand) of the the Mercury Cougar or Ford Mustang. Lens, gasket, and bulb sold separately. Replaces Ford part # C7ZZ-15511.

Used backup / reverse light for the passenger side (right hand) of the the Mercury Cougar and Ford Mustang. Lens, gasket, and bulb sold separately, but we do have a kit available. These used lights will often have a minimal amount of pitting on the inside close up to the lens. Perfect inexpensive replacement item for those wanting to keep their car all original and match the overall patina of their low mile car. Casting number as seen on the back side reads C7ZB-15515-A.Replaces Ford part #...

Reproduction backup light mounting spacers for the Mercury Cougar or Ford Mustang.

This is the 3 hole version of the ball joint for the 1967 - 1973 Cougar and Mustang. Right is same as left. Two required per car. Hardware included. made in Tiawan.

This is the 4 hole version of the ball joint for the 1967 - 1969 Cougar and Mustang. Right is same as left. Two required per car. Hardware included.

Reproduction barrel nut or insert for attaching "Cougar" fender script to the fenders. Each Cougar emblem uses 4 of these barrel nuts which insert into the fender first, and then the Cougar emblem. Additionally, these nuts also go into the C pillars for attaching the XR7 badge or medallion on each side. Two barrel nuts per side for the XR7 medallions. Barrel nuts sold individually. The install is basically the same as shown here: https://youtu.be/mcd788WUNns ...

C8AF-9600-C Standard air cleaner base for all 1968 289-2V (C code), 302-2V (F code), 302-4V (J code), and 390-2V (X code). This is for a closed emissions system (IMCO), that included an oil cap with a fitting going to the air cleaner base and a PCV valve in the passenger side valve cover. About 17.84" inches in diameter. Identified with round nuts welded on the inside for mounting the air cleaner snorkel. Otherwise the same as C8AF-9600-G. Ford part number C8AZ-9600-D.*Note - Canada did not...

Reproduction group 27 battery heat shield that fits many Mercury Cougar and Ford Mustang applications from 1967-70, on most hi-performance engines. It was often the first part discarded but serves a real purpose. Nice American made part, stamped with Ford numbers C7ZB10A682B and C7OB10A682B. There is also a D0... sized for group 24 heat shield offered for 1970-73. *Trivia - these battery heat shields were often trimmed down to fit group 24 batteries.Click on the link below to find some...

Each of these great OEM Style kits include all three required cables, proper terminal and post clamp ends. Unlike CONCOURS CORRECT cables, these do not have the Ford part numbers on them. Starter cables are properly shielded from heat. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part # : C8ZZ-14300- ...

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part # : C8ZZ-14300

No more crust, white powdery battery terminals. Just spray this stuff on, and after a few minutes....simply wash off with water! Not only can you use this stuff on your car, you can use it on your ATV's, quads, dirt bikes and even your ride on lawnmower! A handy item to have laying around your garage. Of course, there's a little more messy, mostly free alternative which you can find the ingredients for online, but why bother? This is a simple, fairly cheap product to have.  

This battery cover is designed to be used with any maintenance free flat top battery **24/60 series with original terminal location for the Autolite battery covers.

Reproduction "Battery OK" Decal for the 1967 - 1982 Mercury Cougar / Ford Mustang

Perfect fit the first time. You will be happy with this Group 24, quality reproduction and check out the price! These battery trays are a popular item for restorers since most of the originals have been destroyed by leaking batteries over the years. Replaces Ford part #: C7ZZ-10732-D.

Good used group 24 tray for 1968-70 Mercury Cougar or Ford Mustang. Assembly line installed group 24 battery tray, for those that want to keep it very original, this is getting to be a hard to find part with no rot (will show pitting).

Concourse Correct with 22 & 24 series batteries for Mustang, Cougar and Shelby GT350/500 made in the USA by Mansfield Mustang to orig. Ford Specs includes attaching bolts Replaces Ford Part # C8ZZ-16060-A

Reproduction Battery Tray Bolts & U Nuts for the 1968 Mercury Cougar / Ford Mustang

For those cold days in the garage, keep your head warm with our 100% acrylic knit 8" beanie. Classic black color with an embroidered WCCC walking cat logo on the front. Also works as a head collision absorber for those who own 1970 Cougars and work under the hood (you know what we mean). Great gift idea for Cougar fans, and for those who prefer beanies over baseball hats.

New axle bearing for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars.These should be professionally installed with a bearing press.

Reproduction steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. Outside diameter: 1 1/2" Inside diameter: 1 1/4"*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used lower steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. The upper bearing can be found here. Outside diameter: 1.500"Inside diameter: 1.060" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

NOS long shaft bearing for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180".  Shaft length (sticking out of bearing) 1 1/8" Ford numbers C4AZ-2990-A, C4AA-2A898-A. ...

Repair your own idler / tensioner with our bearing for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180".  Shaft length (sticking out of bearing) 1 1/8"Overall length 2-3/4" Ford numbers C4AZ-2990-A, C4AA-2A898-A. ...

Repair your own idler / tensioner with our kit which includes a dust cover and is for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180".  We have had a machinist shorten the shaft on these bearings so that they are easily pressed into the cast pulley brackets that use the short...

Manual transmissions, include both 3 and 4 speed Top Loader transmissions. For use with 164 tooth flywheels. For use with all 1968 302 engines and 1969 - 1970 Boss 302 Eliminators. Cast aluminum construction. Shipped bare, no hardware or clutch fork. Search words 68 69 70 small block F J G code. Ford part number C5AZ-6392-BCasting number C5AA-6394-B *Note - This is not a replacement for 1970-1977 Ford Maverick or Mercury Comet 302 engines. See part C5DA-6394-A with 157 tooth flywheels. ...

Reproduction bellows and clamp for your 67 - 69 Cougar or Mustang Midland power brake booster.

NOTE: At the moment the supplier is only making the late model version of this beltline kit. The late version has a slight bend in the chromed quarter piece, whereas the early version is straight (see photo above). Made With Exact Materials As Original. Eight piece kit that includes inner and outer belt-line, enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them...

Grade A used A/C center vent for XR7 (non Standard) model Cougars. These will have some minor chrome blemishe in the plating, but no heavy pitting or damage. Fits the XR7 model (65B) Cougars with woodgrain dash faces. See our other listing for Grade B versions of this air conditioning center register or vent. *Note - Will not fit Standard model Cougars. Replaces Ford number C7WY-19893-D.

Reproduction A/C center vent for XR7 (non Standard) model Cougars. These are great quality vents with bright chrome finish. Fits the XR7 model (65B) Cougars with woodgrain dash faces. *Note - Will not fit Standard model Cougars. Replaces Ford number C7WY-19893-D.

Grade B used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Some blemishes as shown. No extra parts included, levers and switches available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19A976-F Register and Control assy. (Bright Finish). Bright finish is Cougar, Ford Mustang bezels had black pebble grain or wood grain finishes attached. Ford casting number on reverse of this piece is...

Grade A used A/C center vent for standard (non XR7) model Cougars. These will have almost perfect chrome plating, minor blemishes only, no major pitting. Fits the standard model (65A or 65C) Cougars with padded dash face pads. See our other listing for Grade B versions of this air conditioning center register or vent.*Note - Will not fit XR7 model Cougars.Replaces Ford casting number C7WA-19623 and C7WY-19893-A.