1968 Mercury Cougar

Reproduction A/C suction service valves for Mercury Cougars and Ford Mustangs equipped with factory A/C.

Used A/C suction service valves for 1967-68 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used low pressure or suction valve for installation on either York or Tecumseh air compressors. Has the 7/8" inch flare fitting for suction hose. Note that this has the 'Flare' style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and have...

Exact reproduction pair of originals and a must for that detailed engine compartment, but in stainless steel. It is little details like these that will often separate 1st from 2nd place at a show.Replaces Ford part # C5ZZ-19752-C.

Used servo cover from a 1967-68 Ford C-4 transmission. This cover has the big A cast into it, which designates it as an "A" servo. Cover only, marked C6AP-7D027-C.

Reproduction set of Deluxe seat belts for the 68 - 69 Cougar or Mustang Coupe. Some things you may want to notice are that although these are made to fit both 68 and 69, the webbing is the 68 style. 1968 belts had four rows of material that make up the belt and 1969 belts had three rows (as seen in the picture above). Also, the rear belts will not have the plastic sheaths that keep the belts from falling in between the seats. These belts are premium quality and come complete with deluxe...

378696-S Special set screw for the front door channel and vent window frame. This one is longer than the one that installs in the rear door window guide. This set screw has a 5/32" hex head with 5/16" NC threads and is 1-7/8 inches in overall length. This set screw also has a 1-1/8 inch diameter shoulder. Sets and holds your front door glass and vent window angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual...

New 8-32 set screw for the rear window crank handles. Fits 1968-70 Mercury Cougar and Ford Mustang. Allen hex size of 5/64".

Correct shackle for all 1967 through 1973 Cougars, except those manufactured between 10/70 and 9/71. Measures 3-1/2 inches from center to center. Bushing dimensions: Length 1 1/8", outside diameter 1" (shaft piece) - 1 1/4" (end piece), hole diameter 1/2" Sold individually, two required per car. Replaces Ford 5630 shackle kits that include bushings C4GY-5781-A and D4DZ-5781-A.

Correct length (3-1/2 inches from center to center) and construction shackle for all 1967 through 1973 Cougars, except those manufactured between 10/70 and 9/71. Ships complete - 2 piece shackle with original nuts. New bushings not included, but recommended. Sold individually, but two are required for the rear suspension. Replaces Ford 5630 shackle kits that include bushings C4GY-5781-A and D4DZ-5781-A.

Complete Set of 1" leaf spring poly bushings for the rear eye of the spring shackle. Sold in packages of 8, 4 per side. Correct size for the 1967 - 1973 Mercury Cougar except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: D4DZ-5781-A. May be dropshipped. *except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71.

Complete Set of 1" leaf spring rubber bushings for the rear eye of the spring shackle. Sold in packages of 8, 4 per side. Correct size for the 1967 - 1973 Mercury Cougar except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: D4DZ-5781-A. *except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71.

Shaft or rod for the A/C damper blower door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft is clocked differently than the 1969-73 version. This air conditioning damper door is in front of the blower or fan in the center of the car. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number...

Shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. This is a reproduction of the 1968-70 shaft which had a Ford part number of C8AZ-2478-A. This version uses a special spring clip. We also sell the 1967 shaft, which uses a hairpin clip and washer.

Used shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. We do not have the spring clip available. Ford part number of C8AZ-2478-A. 

WCCC no longer has an in-house service for tilt and tilt-tilt away steering columns 1967-1979. After 2 years of working exclusively with Tony Augustine in MO, we can highly recommend him as one of the top most knowledgeable builders of these unique columns in the world.We now exclusively send all of the columns we sell as rebuilt to Tony for service.He can be reached at 816-210-4779 or 6t8cougarguy@gmail.com Make sure you tell him WCCC sent you! Don Rush, owner of West Coast Classic Cougar....

Shaft or rod for air inlet damper door for any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C7ZZ-19C774-A.

Shaft or rod for the evaporator damper door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft has a tab mounted on the lever, and is clocked differently than the 1969-73 version. The evaporator damper door allows air to pass over the evaporator in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related...

Used lower shaft fixed steering column found from 1968-69 Mercury Cougar or Ford Mustang. This is the portion that mates with the upper shaft that bolts to the steering coupler. 1968-69 lower shafts are 15-1/2 inches in overall length. They also have a lower flange with flat sides. Other Ford fixed lower shafts can be used, in most cases the sheer pins are already broken. Just slide the shafts together for the desired length. WCCC no longer has an in-house service for tilt and tilt-tilt away...

Shaft or rod for the heater damper door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C7ZZ-19C774-B.*Note will not work in 1969-73 A/C boxes.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block 1967-68 Cougars with C-4, automatic transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968. These assemblies are just the main shaft only, and do not come with the accelerator pedal or the throttle linkage. These made in Taiwan assemblies are pretty decent looking but for less money we have original FoMoCo which with a little TLC will look better and the fit is always...

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block Cougars with automatic transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with 390 or 428 Cobra Jet FE big block 1967-68 Mercury Cougar and Ford Mustang with automatic transmission.Ford part number C7ZZ-9725-A.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block 1967-68 Cougars with manual transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968. These assemblies are just the main shaft only, and do not come with the accelerator pedal or the throttle linkage. These made in Taiwan assemblies are pretty decent looking but for less money we have original FoMoCo which with a little TLC will look better and the fit is always superior.Ford...

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with any factory Cougar V8 engine. 289, 302, 390, or 428CJ Cougars with manual transmissions.

Used lower shaft used in the tilt / tilt away steering column found in the 1968-69 Mercury Cougar or Ford Mustang. This is the portion that mates with the upper shaft that bolts to the steering coupler. Overall length of this shaft is 15-11/16 inches long.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

UPDATE 11-19-20: We still do not have the shaft seal dialed in but we are offering this kit with a proven substitute seal until further notice. This kit will recondition most FoMoCo headlamp actuators built from 1967 into the 70's on most any Thunderbird, Torino, Lincoln, Cyclone or Marquis. The kit will service two actuators even though many cars only come with one center mounted unit. If your actuator holds vacuum on the bottom port but does not hold vacuum (or pressure) on the top port then...

This 1967-68 Mercury Cougar and Ford Mustang shield, was installed at the factory to protect the heater motor from being damaged when the Big Block 390-427-428's were being dropped in. As noted in the factory assembly manuals we sell, they were supposed to be removed once the motor was in place. We have found that more often than not they were left in place as it was probably too time consuming to remove them. Technically they should not be in place on a concours car but practically...

This arm is attached to your automatic transmission floor shifter (see picture at left). Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for C-4 and C-6 transmissions. Ford part number C7ZZ-7302-A. ...

C5ZZ-7400-D4Assembly 4 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang. Small block 289 engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition.  Check out our video on rebuilding your shifter below: ...

You will not need to make any modifications to run this leather unit in place of your original rubber boot used on three and four speed manual transmissions.

This 4 Speed Lower Shift Boot attaches to the bottom side of your shifter to protect it from water and dirt. Fits the 67 and the 68 with 289 or 302 engines only Replaces Ford part #: C6ZZ-7138-C.

This reproduction of the 3 and 4 Speed Shift Boot has a metal core base just like original as is the texture. Fits the 67 and the 68. Replaces Ford number C5ZZ-7277-B. Customer feedback found at mercurycougar.net : When I bought my 68xr7 from Don two years ago, our deal was that he would keep the new Magnum 500's and BFG tires that were on the car. I asked him if he would just put some "rollers" on to get the car on and off my dad's trailer. When I got the car, he had put on a...

This bezel was never offered from the factory on a Cougar, but is a very attractive part for those with a manual transmission and no console. This unit works with three or four speed manual transmission and with a rubber or leather shift boot.

Original style, factory 3 speed lower shift boot.Replaces Ford part #: C6ZZ-7138-B

Attaches to the console shifter bezel on any 1967-68 Mercury Cougar or Ford Mustang. We occasionally have these available when we get broken console bezels. This shifter dial was originally attached with heat to a pin connector. To reattach we suggest using glue. These look like it would be easy to detail the white letters for P R N D 2 1 with a careful hand. May have a chipped corner that is not seen when installed. Ford part # C7ZA-7A213A Check out our video on rebuilding your shifter below: ...

Restored shifter T handle as found starting in 1968 and through, 1972 Mercury Cougar and Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little thicker in the body, compared to earlier designs. Core charge applies. Replaces Ford part number C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Precision molded clear plastic with black background under red arrows and white letters. Ford part number C5ZZ-7B052-E. Check out our video on rebuilding your shifter below: ...

Shift kit for the C4 transmission valve body for all 1967-67 Mercury Cougar and 1967-69 Ford and Mustang. This is a standard shift rebuilding kit for your stock valve body.

Shift kit for the C6 transmission valve body for all 1967-73 and 1967-73 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.

Nice reproduction 3 speed black shift knob for the 1968 Mercury Cougar and Ford Mustang and other floor shift Ford products from 1968. Thread size is 7/16-20, will not fit on 1967. Ford part number C8OZ-7213-B. Check out our video on rebuilding your shifter below: ...

This one might cost a couple dollars more than others you may have seen but it is the best in my opinion. This is correct for a standard Cougar, XR7 had a woodgrained finish. Check out our video on rebuilding your shifter below: ...

Very hard to find 69 - 70 Shelby / 67 - 69 Cougar 4 speed shifter knob. Almost a year in development was spent to get as close as possible to original N.O.S. sample. These very rarely come up for sale used and when they do, they are expensive. Knob insert is made of metal just like original not brass. Knob also has the correct groove in middle of body like 69 version and not the earlier version which does not. Not technically correct for a 67-8 Cougar, as the 67-8 does not have the groove in...

Attractive knob used on later 68 through 69 non XR7 Cougars. I recently installed one of these on my own cars and had the face fall off the main body the first time I used it. I glued it back on and have had no problems since. Replaces Ford Part #: C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Used faux wood grain 4 speed shift knob for 1967 and 1968 Mercury Cougar XR-7 models. This knob is so much better than the reproduction knob that we sell. This knob has a threaded metal insert that is 1/2" - 20 NF. Some aftermarket shift levers may not have this particular thread size. Later 4 speed knobs have a groove around the middle, this is an OEM Ford assembly line knob. Ford part number C5ZZ-7213-L. Check out our video on rebuilding your shifter below: ...

For those who want to want a correct looking interior in conjunction with their modern transmission. Check out our video on rebuilding your shifter below: ...

Used on both XR7 and standard Cougar consoles. Differs from shifters made for non console use in that is has a small loop to connect the white plastic arm to the shift indicator light. Fits 1967-68 Mercury Cougar and Ford Mustang with factory consoles. Good used part no heavy pitting on the chrome, comes with complete with cable assembly inside. Ford part number C7ZZ-7210-C. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for any 1967-68 Mercury Cougar or Ford Mustang with consoles. This console lever is unique to console equipped cars, it has a tab with a hole in it for accepting the shift indicator indicator rod. We sell these bare for those car owners that have pitted shifter levers. Ford part number C7ZZ-7210-C. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for any 1967-68 Mercury Cougar or Ford Mustang without consoles. The 1967-68 is similar to the 1969-73 shift lever, but has the additional chrome window section for holding the indicator light. These have been re-chromed, we sell these bare for those car owners that have pitted shifter levers. Ford part number C7ZZ-7210-A. This lever was also used on the 1968 XR7-G cars with unique consoles.*Note - Chromed lever only, sold without cable, pawl, handle,...