1968 Mercury Cougar

Stainless steel battery hold down bolts. Work with standard battery hold down brackets and the billet hold down bracket.

Multiple uses.5/8" from bend to center hole.

Replace FORD Part #: C8WB-17093-B

Replaces Ford Part #: C8WB-17093-D.

Under trunk lid decal for 1968 Mercury Cougar and Ford Mustang with style steel wheel spare tire. Jack usage and spare tire stowage, shows the unique round disc for use with style steel wheels.

This decal goes on the tire jack itself.

Used jumper wire with correct ends for doubling back on the tachometer leads from the under dash harness. Works for all generations 1967-68, 1969-70, and 1971-73 Ford anything and Mercury, and Mercury Cougar with factory tachometers. If your tachometer goes bad, you will not start or keep your engine running. Good for bypassing tachometers for testing and getting home. Keep in your glove compartment or tool box.

Brake switch jumper wire, 4 inch long extension. Bridges the under dash wiring harness and the brake light switch. Not used on many cars, we suspect that it was used on the assembly line when the brake switch plug didn't reach the brake switch. Adding one of these jumpers, saved time from re-routing the under dash wiring harness. This jumper can also be used to repair bad stop light connectors on 1967-70 Cougars and Mustangs (and other Fords) by cutting off the male end and splicing it...

Brake switch jumper wire, 4 inch long extension. Bridges the under dash wiring harness and the brake light switch. Not used on many cars, we suspect that it was used on the assembly line when the brake switch plug didn't reach the brake switch. Adding one of these jumpers, saved time from re-routing the under dash wiring harness. Ford master part numbers: C5AZ-14489-C, C8ZA-13K408-A and C8ZZ-13K408-A

No modifications needed, just open the trunk and plug the unit into your original wiring! We highly suggest considering not purchasing this unit and invest in the all inclusive unit. All of the original sequential components in the trunk of your Cougar are mechanical and will in time fail. It is much more cost efficient to buy the all inclusive unit than to purchase them one by one as they fail. This reproduction is an exact replacement for this original unit. This updated relay will...

Good used metal part that is not bent or heavily rusted. Will need to be repainted. This mounts at the top front corner of the driver side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B. You may also need the attaching screw. Replaces Ford part number C7WY-6531491-B or C7WB-6531491. Fits 67 Cougar Fits 68 Cougar Fits 68 Mustang with body code 65B This icon...

Good used metal part that is not bent or heavily rusted. Will need to be repainted. This mounts at the top front corner of the passenger side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B. You may also need the attaching screw. Replaces Ford part number C7WY-6531490-B or C7WB-6531490. Fits 67 CougarFits 68 CougarFits 68 Mustang with body code 65B ...

Chrome screw used to mount the rear interior panel keeper.Sold individually.

Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford #: C7AZ-6222053-A.

Reproduction economy trunk / glove box key. These keys DO NOT have the Ford logo.Replaces Ford Part #: C7AZ-6243562-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford Part #: C7AZ-6243562-A.

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the ignition / door key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the trunk / glove box key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

This listing is for a Walking Cat keychain multi tool. We haven't been able to find much information on this, but it's definitely a cool item to add to your collection. Features a chrome plated swing out tool with a few flathead tips and nub-style phillips tips. 

Quality part for your C-4 but will work on the C-6 67-68 transmission. Measures 10.2" long. Replaces Ford Part #: C6OZ-7A187-D.

C4 Automatic transmission kick down cable kit for all 1967-68 Mercury Cougar and 1966-68 Ford Mustangs. Kit includes kick down cable assembly, accelerator kick down lever, retracting spring, and related hardware.

Kickdown return spring for 1967-68 Mercury Cougar with C4 transmissions, and 1967-69 Mercury Cougar with C6 transmissions. Same for 1965-69 Ford Mustang with C4 and 1967-69 with C6. Actual Ford part number is C5ZZ-7B146-A.

These were installed behind the kick panels on 1967-68 Cougars & the 1968-69 Fairlane, Torino, Cobra and Cyclone equipped with a factory AM-FM or AM-8 track radio. Easy to install considering you have a built in template behind the kick panels that are easy to cut out. These will accept common after-market speakers in multiple depths. For more discussion on kick panel speaker options, check out this thread. If you only are looking to buy one, please call, we often times have an odd number in...

These were installed behind the kick panels on 1967-68 Cougars & the 1968-69 Fairlane, Torino, Cobra and Cyclone equipped with a factory AM-FM or AM-8 track radio. Easy to install considering you have a built in template behind the kick panels that are easy to cut out. These will accept common aftermarket 5-1/4" speakers in multiple depths. Sold as a pair. For more discussion on kick panel speaker options, check out this thread. Replaces Ford Part number C8OA-19A067-A ...

Reproduction kick panel insulation for the 1967 - 1968 Mercury Cougar or Ford Mustang 

Kick panels for the 1967 and 1968 Mercury Cougar that include 6 1/2" coaxial (2 way) 100 watt speakers. Available in black, but can be sprayed to match your interior. Sold as a pair. For some discussion on kick panel speaker options, check out this thread.

Great way to update your sound system without cutting door panels or other original parts. Great fit and finish, easy installation. Pioneer speakers are 4ohms, 6 1/2" coaxial (2 way) 160 watts per speaker, for a total of 320 watts max output! Only available in black, but can be painted to match your interior with flexible paint. For more discussion on kick panel speaker options, check out this thread.

Kick panels for the 1967 and 1968 Mercury Cougar that are formed to accommodate speakers. Speakers are not included. These are designed for those who would like to choose their own speakers. Available in black, but can be sprayed to match your interior. Sold as a pair. These now come pre-cut for a 5 1/4 inch speaker. For more discussion on kick panel speaker options, check out this thread.

Sold as a pair. The overlay bonded to the plastic really gives a feel and look of quality to these kick panels. For more discussion on kick panel speaker options, check out this thread.*NOTE* These units may require some slight modification to fit perfectly in your unique Cat or Pony.

Sold as a pair. The overlay bonded to the plastic really gives a feel and look of quality to these kick panels. For more discussion on kick panel speaker options, check out this thread.

Knee pad as found on select 1968 Mercury Cougars. This grade A version will not be separating from the metal strip. Not a common option, your Cougar would have a line of mounting holes across the lower dash and above the glove box if your Cougar originally came with a knee pad. We don't always have these in stock in this condition. Call for desired color, but plan on spraying with a quality vinyl dye for best results. Black is our most popular requested color, and we will probably always be...

Knee pad as found on select 1968 Mercury Cougars. This grade B version will be separating from the metal strip, and or may have warpage. Not a common option, your Cougar would have a line of mounting holes across the lower dash and above the glove box if your Cougar originally came with a knee pad. We always have these in stock in this condition. Call for desired color, but plan on spraying with a quality vinyl dye for best results. This pad is different from the Mustang version which is...

Perfect fit, easy to replace and will be a great upgrade over your original scratched and or pitted knob. To remove, reach behind the dash and locate the small, round spring loaded button on the top side of your headlight switch. Depress the button while firmly grasping the knob and move back and forth until it releases. To install, firmly and quickly press the knob inward (towards the dash) with the palm of your hand.Here is a helpful youtube video on how to go about removing a headlight...

Headlight switch knob for any 1968 Mercury Cougar or Ford Mustang. Not the same as 1967, which is reproduced by Scott Drake. This is a nice detail item for concours judged cars. There is a difference between 1967 and 1968 knobs as shown in the photos.Nice used condition. Original Ford part number C8ZZ-11661-A.

Reproduction inner radio knob used on the Mercury Cougar or Ford Mustang with a factory center console and measures 1-3/8 inches tall. Replaces part # C8ZA-8A932-B

This set of reproduction used knobs is for 1968 Cougar / Mustangs without factory console. The exception to the rule would be the XR7G. Cougars equipped with a console need the longer version of this knob to clear the padded console face. If you happen to have a 1969 or newer radio then the radio has longer shafts and these knobs may in fact work with a console. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear...

Used lower knuckle for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This unit will not interchange with the 1967 tilt / tilt away. This is because the center hole on the 1967 unit is round where this 1968-69 version is elongated. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of...

Used upper knuckle assembly for the tilt / tilt away column for the Mercury Cougar or Ford Mustang equipped with a tilt / tilt away steering column. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* We'll give you UP TO $100 cash back for your old knuckle assembly. The amount you will get back will depend upon how many usable parts that can be salvaged from your old unit. *NOTE* For tilt column service, you can contact Tony...

Good used "L" bracket for the tilt cable adjustment on the 1968 and 1969 Cougar or Mustang.

Reproduction Large Wire Loop Strap for the 1968 Mercury Cougar or Ford Mustang 

Zinc plated, visually correct copies of the original, very prone to failure... We highly recommend buying our good used latches linked here even though they may not look as pretty. No warranty on this low quality off shore part.Replaces Ford Part # C5AZ-6243200-ACheck out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

During installation, check for proper alignment with trunk latch. Trunk latch and striker should engage smoothly, both items are adjustable. We only save the rust free latches with no wear or rust, the rest are tossed. Fits 1967-68 Mercury Cougar. Ford part number C6OZ-6543252-A.

Used cast iron lateral compressor support bracket for Cougars and Mustangs built after 1/3/1967 and 1968 cars built prior to 3/1/1968, for both the 289 and 302 engine. Must be used with adjusting bracket C7AZ-8678-B pulley assembly, and pedestal bracket C7AA-2882-L.Ford part # C7AA-2888-G or C7AZ-2888-F.

Used stamped steel lateral compressor support bracket for Cougars and Mustangs built after 3/1/1968 with the 289 or 302 engine. Very close in design to the 1969 351 Windsor, but smaller overall.Ford part # C8AZ-2888-B.

Used steel lateral support brace for Cougars and Mustangs with the 390-2V, 390-4V, or 428CJ FE engines. Identical to the 1970 FE lateral bracket except 1970 versions have square nuts on the reverse.Ford part # C8AZ-2888-A