1968 Mercury Cougar

Hex screw for attaching the black plastic elbow to the right or left hand A/C dash duct. Correct replacement #8 washer head tapping screw. Sold individually, two needed per car. One on each side. Fits 1967-68 Mercury Cougar and Ford Mustang with factory air conditioning.

Reproduction 97 License Plate Light Bulb for the 1967 - 1973 Mercury Cougar

Reproduction driver side inner A pillar inner / kick panel for the 67 - 68 Cougar or Mustang.

Reproduction passenger side inner A pillar inner / kick panel for the 67 - 68 Cougar or Mustang.

Seals the hole where the A/C lines pass through the core support on the driver side on Mercury Cougars and Ford Mustangs. Replaces Ford part #: C7ZZ-19810.

This replica tag is of a lower quality than the originals were. The aluminum stock from which this Mercury Cougar A/C tag is made, is about half the thickness of original and the font, instead of being white, is unpainted aluminum. This is a cheap looking, and feeling, part compared to the original. We do have the clip that holds it in place. Check out the product images for an example of factory placement for this tag.

Air conditioning fan blower BARE clam shell assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade A used may have a minor stress crack or small chip. The holes for attaching duct work will be good. See Grade B for a lower cost version. There are a couple of versions of this housing. There is a version with a cooling nipple for cooling the...

Air conditioning fan blower BARE clam shell assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version. There are a couple of versions of this housing. There is a version with a...

Air conditioning fan blower assembly for any 1967-68 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.

Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...

York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...

Redesigned modern evaporator has 35% MORE PASSES, using three-circuits, instead of the original single-circuit design. This is a direct bolt-in replacement and requires no modification.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal. It has been our experience that these often fail within a few years. We suggest flushing and pressure...

Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade A vents will not have any cracks or breaks.

Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade B vents will mostly have a missing metal bracket and / or small crack or break usually around the mounting holes.

Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Nice fit, made of plastic. Will work with or without console, has slightly wider wings for clearance of the rear of the factory installed consoles.

Used A/C floor duct for 67 - 68 Cougars and Mustangs without a console. Grade A vents will not have any cracks or breaks.

Used A/C floor duct for 67 - 68 Cougars and Mustangs without a console. Grade B vents will have a small crack or break usually around the mounting holes, but will not effect it's functionality.

Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs without a console.

Concours correct A/C discharge hose for Mercury Cougars and Ford Mustangs.Replaces part # C7AZ-19972-A or C7ZZ-19972-A.This hose is compatible with both 134a and R12 refrigerants.

Concours correct A/C sight glass hose with a 90° fitting for your Cougar or Mustang.This hose is compatible with both 134a and R12 refrigerants.

Concours correct and constructed in original Ford style black thermoplastic material with a nylon barrier. This hose assembly is built to be compliant for R-12 or 134a refrigerants.NOTE: We have three hoses from a previous supplier that we have available for about half the price. The only difference would be that instead of the thermoplastic material, these are the standard rubber type hoses. Pick one up here. ...

Regardless of which V-8 engine, C8ZA-19867-C is the correct part number. This hose is approximately 55 inches long.Ford MPC part # C8ZA-19867-C.

Reproduction underhood A/C performance upgrade kit for the 1967 - 1968 Cougar equipped with the 289 or 302 engine.  This kit combines the compressor conversion kit with a Superkool condenser assembly, new barrier style A/C hoses and expansion valve to maximize the performance of the factory A/C system. Also includes a compressor safety switch to protect the new components from excessive high or low system pressures. Excellent choice for vehicles being retrofitted for newer automotive...

For 1967-68 Mercury Cougars and Ford Mustangs with the 289 or 302 engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5-16", a clutch diameter of 6", and an overall thickness of 2 inches. This version uses the Eaton style of brush, which is available new.Ford part # C7AA-2981-G.

Finally, an answer to the much needed, delicate 1968 A/C side vents! Visually these are very hard to tell apart from the originals we have listed on this site, but functionally, they are much better in that they are cast in one piece. The originals were very prone to breaking and often when you close the door on your 1968 Mustang, Cougar or Shelby the lower portion of the vent falls off. Includes all three control knobs and dealer pricing available.

Used air conditioning vent for any 1968 Mercury Cougar or Ford Mustang with factory installed A/C. These are different than the 1967 A/C vents. For 1968 the vents detached from the main housing for safety reasons. These were meant to 'break away' in the event of an accident. These attach to the housing with a spring, spring sold separately. Grade B decent chrome, there will be some blemishes and minor pitting. A grade versions also available. Fits both passenger and driver side for 1968....

This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent that was very prone to failure. This is a fixed, one piece body and will not fall apart. This will be a direct fit to your Mercury Cougar with no modification needed. Dealer pricing available. *NOTE* Mustang used the shorter version of this vent than the Cougar did, otherwise they are visually and mechanically the same. Fits: 1967 Mercury Cougar 1968...

Work perfectly with our reproduction A/C registers.Ford part # C7ZZ-19C692-A.

Passenger side A/C duct register, or elbow, connector for Mercury Cougars and Ford Mustangs equipped with integral or factory A/C. These elbows work perfectly with our reproduction A/C registers.Ford part # C7ZZ-19C692-B.

Reproduction set of A/C register connectors for Mercury Cougars and Ford Mustangs with integral A/C. These mount directly behind the round dash vents and work well with both the original vents or our high quality reproduction vents.

Grade B used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Will have obvious pitting and minor blemishes. No extra parts included, spring is available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19C784-A Register and Bezel. (Bright Finish). Ford casting number on reverse of this piece is C8ZA-19C784. Mustang used a shorter bracket, on the reverse you can see the witness line and...

These selector buttons are top quality reproductions with a lot of attention given to the details to make these little units look factory fresh and correct.

Vacuum switch not included. This consists of the two lever assembly for the vacuum and cable actuation of the air conditioning plenums damper doors on your 1968 Mercury Cougar or Ford Mustang with integral A/C.Replaces part # C8ZZ-19B888-A for the switch assembly.

Fits 1967 Cougar and Mustang with factory Heater Only Firewall and 1967 289 engine. Custom Hurricane Heat Cool & Defrost System for 1967-68 Mercury Cougar / Ford Mustang with original 289 V-8 with or w/o Power Steering. Easy to Install! Hurricane Unit mounts to firewall in place of factory heater, a/c & heater fittings pass neatly through original blower motor hole with custom rubber grommet. Electronic switching package includes correct reproduction A/C Control bezel w/ louvers. Electronic...

Reproduction A/C Tag Retainer for the 1967 - 1973 Mercury Cougar

Grade B A/C vacuum canister that has a non working check valve. Suitable for filling the hole in your passenger side fender apron. This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and not holding vacuum, tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's...

This A/C vacuum canister mounts to the passenger side fender well and controls doors inside the A/C unit. This unit includes a built in check valve. Fits 1968-1970 Mercury Cougar and Ford Mustang. The collapsing or imploding problem has been resolved on this vacuum reservoir with the addition of the ribbing for strength.  Replaces Ford part # C8ZZ-19A566.

Reproduction Air Conditioning Vent Air Door Axle for the 1967 and 1968 Mercury Cougar or Ford Mustang.

Reproduction Air Conditioning Vent Air Door for the 1967 and 1968 Mercury Cougar or Ford Mustang.

Round air conditioning vent registers for all 1967-68 Mercury Cougar and Ford Mustang with factory A/C.

Reproduction factory air conditioning vent register knob. This knob controls the black vent door or valve inside the round registers. These will fit the original axle shafts, but will need to be attached with some super glue or other adhesive. These new knobs fit our reproduction axle shafts that have new splines on them perfectly. Please note the position or orientation of the knob in relation to the position of the internal black plastic butterfly.

Black plastic retainer for attaching the direction air conditioning vent registers.

Finally, an answer to the much needed, delicate 1968 air conditioning side vents! Visually, these are very hard to tell apart from the originals we have listed on this site but functionally they are much better in that they are cast in one piece. The originals were very prone to breaking and often when you close the door on your 1968 Mustang, Cougar or Shelby the lower portion of the vent falls off. This kit is correct for the 1968 Mercury Cougar only and it includes all three knobs, right and...

Finally, an answer to the much needed, delicate 1968 air conditioning side vents! Visually, these are very hard to tell apart from the originals we have listed on this site but functionally they are much better in that they are cast in one piece. The originals were very prone to breaking and often when you close the door on your 1968 Mustang, Cougar or Shelby the lower portion of the vent falls off. This kit is correct for the 1968 Mercury Cougar only and it includes all three knobs, right and...

Reproduction passenger side A/C vent with black camera case finish for the 67 - 68 Mustang. 

Finally, an answer to the much needed, delicate 1968 air conditioning side vents! Visually, these are very hard to tell apart from the originals we have listed on this site but functionally they are much better in that they are cast in one piece. The originals were very prone to breaking and often when you close the door on your 1968 Mustang, Cougar or Shelby the lower portion of the vent falls off. This kit is correct for the 1968 Mercury Cougar only and it includes all three knobs and the...

part # 370608-S. Used in multiple places on mounting brackets.

This Accelerator Pedal Rod To Firewall Grommet reproduction fits both the 67 and the 68. Replaces Ford part # C6OZ-9793-A.