1968 Mercury Cougar

The originals hang at a slightly different angle than the reproductions. Comes as shown with original rubber insulator. New rubber available upon request. Seldom in stock, we suggest the 1969 small block version. It is very close to this one. Please see related item. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.

Reproduction power steering hose retaining bracket and retainer. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Bracket and retainer will work on 1967-70 Mercury Cougar and Ford Mustang with small block V8 cars with the correct length of power steering hoses.

Fits 289 / 302 / 351 1967-69. Comes as shown with rubber insulator. Replaces Ford part # C7DZ-3A609-A, C7DZ-3A610-A, C7ZZ-3C510-B, and C8ZZ-3C510-A.

Two of these little plastic protectors came on Mercury Cougars and Ford Mustangs equipped with Air Conditioning. They are affixed to the front cross member using the same bolts that holds your condenser in place. Their purpose was to protect the wiring harness from potential damage if the car were to get into a collision. These are very hard to find today as most were discarded the first time the condenser was replaced. Even your most experienced judges usually have never seen or heard of this...

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561693-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561692-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

Reproduction passenger side (right hand) front wheel cylinder for 10 inch x 2-1/2 inch drum brakes. This unit fits in a 1-3/32 inch hole on the brake backing plate. Replaces Ford Part # C6OZ-2061-B or C9TZ-2061-B.

C9OZ-2212-C Left hand rear brake backing plate for use with 1-3/4 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Also used on 6 cyl and 302 Mustangs in 69-71. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 70867. Originally manufactured by Bendix part number 319480.

C9OZ-2211-C Right hand rear brake backing plate for use with 1-3/4 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Also used on 6 cyl and 302 Mustangs in 69-71. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 70866. Originally manufactured by Bendix part number 319481.

C9OZ-2212-B Left hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71086. Originally manufactured by Bendix, part number 317558..

C9OZ-2211-B Right hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71085. Originally manufactured by Bendix, part number 317559.

Complete Midland core booster with both input and output rods in place. No visible cracks in bake-a-light plunger. Will show some rust pitting, most notable on the bottom side where previous leaking master failed, but not excessive. Check out our videos below, one on how to convert a manual drum brake car to factory disc brakes, and the other on boosters, differences, do's / don'ts: This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a superior quality core.You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

This option includes paying a core charge. By choosing this option, the rebuilt booster you receive will have started the rebuild process as an average quality core.We highly recommend that you send us your core first. Here's why:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a superior quality core.You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

We have discontinued this booster because of changes that made it no longer fit correctly. This reproduction brake booster looks and fits more like the originals than any other on the market. This is an off-shore unit, but of the many out there, it is the only one we feel you can consistently get 10 or more years out of. It comes with a 3 year warranty and no core exchange is required. If you do have a decent original core (any version 1967 - 1970 Midland or Bendix brand), we can credit...

This option includes paying a core charge. By choosing this option, the rebuilt booster you receive will have started the rebuild process as an average quality core.We highly recommend that you send us your core first. Here's why:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a superior quality core.You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

Power disc brake distribution block with proportioning valve. Mounts to the driver side fender apron with two nuts. Plan on testing and or rebuilding before installation. Rebuild kits available here. You'll also need hard lines and the brake warning switch, which is available new or used. Ford part # C8ZZ-2B257. Here’s a video to help you rebuild the distribution block so that you can corral your Cat or Pony without fearing for your life. ...

C3OZ-1126-B Used brake drum with the vintage casting look. Guaranteed to successfully be turned and not exceed the manufacturers inside maximum of 10.060". When we say the "vintage casting look", we mean with the proper groove and contours. Reproductions are fine, but do not retain the casting design of the original casting company. When looking for used brake drums, the rule of thumb is to find ones with a brake surface area of 1/4 inch more than the brake shoe width.

Flexible high pressure replacement brake hose for the rear drum brakes on Mercury Cougar and Ford Mustang. The Ford MPC specifies that the 427, 428 and Boss 302 cars used this slightly different hose. The most noticeable difference is the bracket that attaches to the differential and the larger size fittings. Attaches to the rear end housing. Replaces Ford part number C9ZZ-2282-A.

This reproduction OE steel brake line kit for Mercury Cougars equipped with the 9 inch rear end with 28 spline axles and is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

This reproduction power drum brake line kit is for Mercury Cougars and Ford Mustangs equipped with the 8 inch rear end and 28 spline axles. It is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

Stainless steel version features extra corrosion protection with correct zinc chromate plated fittings and are exact copies of the originals with color coded fittings.

Steel tubing features tin/lead coating and plated zinc chromate fitting and are exact copies of the originals with color coded fittings. New copy of the 1968-69 Mercury Cougar and Ford Mustang manual drum brake master cylinder lines. 

Two piece pre-bent OE steel brake line kit that runs down the rear axle on the 8 inch rear end of a 1967, 1968 or 1969 Mercury Cougar or Ford Mustang.The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for...

Two-piece Stainless Rear Axle Brake Line Set 67, 68 & 69 Mercury Cougar and Ford Mustang with 9"-28 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help with any...

Also correct for some 1967 models with proportioning valve at front

Replacement brake pedal pad trim for the Mercury Cougar or Ford Mustang equipped with a manual transmission. Replaces Ford part # D1ZZ-2A487-B.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with a manual transmission and drum brakes. This unique pedal that works with the wider collapsible 1968 steering column and with a clutch pedal. Shorter arm than power brake pedals. The picture may show hardware and pedal pad with trim, but the pedal is shipped bare.Ford part # C8ZZ-2455-E.

Unique pedal that works with the wider collapsible 1968 steering column and with a clutch pedal. Longer arm than drum brake pedals. Keep in mind automatic transmission brake pedals can be trimmed down to work as manual transmission pedals. Pedal shipped bare, picture may show hardware and pedal pad with trim. *Note* On some 1968 Cougars you will have to drill holes in your existing pedal hanger (many are pre-drilled) to accomomdate the power brake pedal. Since systems with a vacuum booster...

Reproduction driver side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability, the...

Reproduction passenger side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability,...

Reproduction pair of drum spindles for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and...

We have had so many dealers inquiring about these we are now offering dealers, and those who own multiple cars that use these rare bulbs, a quantity discount. We have witnessed these bulbs sell for as much as $9 each on ebay! The 1968 Ford Manuals call for a 97N bulb, but that is an error believe it or not. 

This money saving kit gives you all four rubber bumper fillers that wedge into the 67-8 front and rear bumpers horizontally (the triangular ones) as well as the vertical ones that fasten to the leading edge of the fenders and quarters. Keep in mind when you remove the old rubber parts that we can give in-store credit for reusable parts. Please only send us parts that are not ripped, gouged or warped.

Used driver side (left hand) bumper guard for the Mercury Cougar. The chrome plating was pretty low quality back in the day and this unit will show some scratches and pitting as it is an almost 50 year old original part.Ford part # C7WY-17997-A for the driver side.

Used passenger side (right hand) bumper guard for the Mercury Cougar. The chrome plating was pretty low quality back in the day and this unit will show some scratches and pitting in the chrome as this is an almost 50 year old original part.Ford part # C7WY-17996-A for the passenger side. ...

(7526) Nylon plastic injected. New Old Stock. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where...

New Old Stock lower distributor bushing for most V-8 engines 1965 through 1968-69. Ford deemed this bushing as not needed during 1968. That is why all 351W distributors do not have one installed. All 289 distributors 1965-67 should have one installed, starting in 1968 some did, some did not. Many 1968-69 302-2V's and all Boss 302 distributors had them installed. Same with FE distributors all had them starting in 1965, by 1968-69, they were disappearing. Limited to stock on hand. If Ford deemed...

Although this premium reproduction strut rod bushing kit appears very similar to the economy kit, they are in fact superior. The main difference being that the bushings are made from a higher quality rubber compound.Replaces Ford Part #: C6OZ-3A187-AR.

Reproduction pair of brass 3/8 ID bushings for the clutch rod. Protects clutch equalizer and rod, and removes excess play.We also sell these in nylon. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it...

Reproduction ram cylinder bracket bushings for the 68 - 70 Cougar or Mustang. If you're having trouble with the bushings on your car ripping or tearing through the hole in your power steering ram cylinder bracket (more so with our reproduction drop down bracket), you can purchase this pair of polyurethane bushings to replace your existing ones. The boot kit we sell also comes with similar bushings, but are a lower quality item, so this set should solve your problem. Sold as a pair. ...

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.See item 31804 for new clip.

Reproduction front emergency / parking brake cable for the Mercury Cougar or Ford Mustang. These are made just like the originals, are concours correct and includes the firewall seal and firewall bracket. Replaces Ford part # C7ZZ-2853-A.

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

This used emergency / parking brake cable connector is for the Mercury Cougar only. That is because it is longer than the Mustang version due to the Cougar's longer wheelbase. This connector connects the two ball ends of the long and short emergency brake cables. Ford part # C7WY-2A790-A.

This reproduction emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. A very nice reproduction!Replaces Ford part # C6OZ-2A602-A.