1968 Mercury Cougar

Used seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1 or Ford Service part number D1AZ-10B924-A

This is a "better quality" non-concours starter solenoid. It's just one step above our "generic" solenoid also listed on our site. An inexpensive replacement if you are not worried about being 100% correct. More often than not, these lower quality solenoids fail within a year or two so we always recommend buying original FoMoCo. Replaces Ford part # B6AZ-11450-A, C7AZ-11450-A & D2AF-11450-A.Cougar Applications:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury...

This is a good quality non-concours starter solenoid. Inexpensive replacement if you are not worried about being 100% correct. Disappointing quality, often will fail in less than a year, we recommend buying original FoMoCo. Replaces Ford part # B6AZ-11450-A, C7AZ-11450-A & D2AF-11450-A.

This is a replacement relay for the discontinued original FoMoCo relays.  It does not appear in the same form factor, but will work just fine. The original is a metal cased unit, the replacement is plastic.  Original relays are marked either C7ZA-3E553-A (1967) or  C8ZA-3E553-A (1968 & 1969) on the mounting tab. Click Here to Download Instructions (340Kb pdf). Replaces Ford Part # C7ZZ-10B926-A or C8ZZ-10B926-A *NOTE* For tilt column service, you can contact Tony Augustine at...

Used tilt / tilt away steering column lock relay for the Mercury Cougar or Ford Mustang. Keep in mind we have a reproduction substitution for this part. This unit can be identified with the bend in the bracket compared to the 1967 relay which is straight. These relays are tested by our electrical department. Ford part # C8ZA-3E553-A. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting.*NOTE* For tilt column service, you can contact...

This is referred to as the "K5" relay in the Ford service manual. This relay causes the flashing action of the 1968 Mercury Cougar instrument panel indicator lights. The number stamped on this relay is C8WB-13A366-A or C8WB-13A366-C, the Ford part number is C8WY-13A366-A or C8WY-13A366-C. Stay tuned for an upcoming electronic version of the 1968 K7 relay.*Caution - Do not use the 1967 relay in place of the 1968 relay, smoke and fireworks will be the result.

This is referred to as the "K5" relay in the 1968 Ford service manual. (In 1967 it was called the K7). This relay causes the flashing action of the 1968 Mercury Cougar instrument panel indicator lights and almost never works... The number stamped on this relay is C8WB-13A366-A or C8WB-13A366-C, the Ford part number is C8WY-13A366-A or C8WY-13A366-C. We suggest replacing this unit with our new and improved solid state unit.*Caution - Do not use the 1967 relay in place of the 1968 relay, smoke...

At last, there's a solution to a problem that almost all early Cougars suffer from. If the turn signal indicators in your dash only blink once, and then pulsate slowly without going out, you need this new electronic relay. It's a direct plug-and-play replacement, and it will give your indicators a nice on-off flash, complete with a mechanical click sound, all in time with your turn signals. We're excited about this simple fix; it's great to see and hear the indicators working properly. The...

1968 Mercury Cougar K-8 and K-9 turn signal relay assembly. K-8 for the passenger side, K-9 for the driver side turn signals. Also is integral to the brake light circuit. Clean used unit that is tested and will be functional. This unit will not be rusty, have internal water damage, May have minor repairs, no cut wires. Trouble shooting these systems is takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. When these relays are not energized,...

1968 Mercury Cougar K-8 and K-9 turn signal relay assembly. K-8 for the passenger side, K-9 for the driver side turn signals. Also is integral to the brake light circuit. Clean used unit that is tested and will be functional. This unit will not be rusty, have internal water damage, May have minor repairs, no cut wires. Trouble shooting these systems is takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. When these relays are not energized,...

Used release lever for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is sometimes also called a bale. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

High quality chrome finish on lever & base. Improved cable for smooth operation. You must have correct trunk latch to use this remote. Detailed instructions included. Look for the trunk latch in our 'related items' tab.

New old stock Ford accessory cable trunk popper. Fits late 1967 - 1973 Mercury Cougar and other Ford products. Lever release, cable and hardware, NOS Ford. Detailed instructions included. Latch not included with this kit. Sorry, the way it came. This kit was a dealer sold kit or over the counter kit. Fits a large range of Ford cars. Ford part number C4AZ-62432A00-A. *Note - All 1967, and most 1968 trunk lids will not have a large enough access opening in the under side structure to...

This is an upgrade to the Electronic Trunk Release. Allows trunk to be opened with just the push of a button on two wireless remotes that are included. NOTE: This item requires that you have a latch mechanism equipped with the remote release tab.

New to the market grille fix for 1967 - 1968 Mercury Cougars / Patent Pending. These simple little grille repair clips have been needed since these cars were new! Over the years we have seen a multitude of home remedies to fix this common problem but none were this clean looking, easy to install and failure proof. Soon we will be listing all the different FoMoCo applications these clips will work on. These clips are sold as a set of four. NOTE: We've found that removing the legs from one side...

Reproduction repair kit for your 69 - 70 Cougar or Mustang Midland brake booster inner control valve.When doing the repair on your booster control valve, be sure to use any type of synthetic blend grease and lubricate the following:Inside lower end of the bellows, all O rings and insides of the seals and inside the front diaphragm.Included in this kit are 3 O rings, fiber washer, rubber valve, spring and spring seat and spring retainer.

These clever kits allow you to replace the broken cam without having to swap the whole assembly. Mounting hardware is included. Works on 67-72 fixed columns and 67-73 tilt columns. Replaces Ford Part # C7SZ-13318-B and D0AZ-13318-A. Watch Install Video

This kit has everything you need to repair your clutch and brake pedal and pedal support in one easy kit.Repairs 1967-70 Mercury Cougar or 1965-70 Ford Mustang. *Hint - All 1967-70 brake pedal hangers have the clutch pedal shaft bushings, even the automatic cars. The originals are swedged in. * Does not fit 1971-73 Mercury Cougar or Ford Mustang.

New metal clips to replace your worn out original fuse holders.

This great little kit replaces stock Ford bushings that can wear out in as quick as one year. This is a very simple repair and upgrade, once you have removed the pedal support from the car. Upon completion of this you will be rewarded with greatly reduced pedal pressure and the knowledge that you will never have to replace these bushings again. This is a must have for anyone with a manual transmission.Does not fit 1971-73 Mercury Cougar or Ford Mustang.

Reproduction driver (left hand) side drum brake self adjustor repair kit for your Mercury Cougar or Ford Mustang. This kit contains all the parts necessary to refurbish the self adjusting mechanism on drum brakes. Includes new cable and guide, ratchet, spring, and all necessary small parts. Kits include everything for one wheel.

Reproduction passenger (driver hand) side drum brake self adjuster repair kit for your Mercury Cougar or Ford Mustang. This kit contains all the parts necessary to refurbish the self adjusting mechanism on drum brakes. Includes new cable and guide, ratchet, spring, and all necessary small parts. Kits include everything for one wheel.

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved.  Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold Individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71 - 73 = 16 front, 18 rear Here's a handy...

Used roll up door replacement slat. If you damage one you can remove the door, slide the damaged slat off the rubber backer and slide the replacement in. Sold individually.

Correct original windshield washer reservoir cap with "Mercury Man" logo. All the replacements are plain as was the Ford products that used this same cap configuration. Ford part number C7AZ-17632-A

Used OEM Ford heater blower motor resistor that attaches to the heater blower fiberglass housing. We inspect these for damage or broken wires and we guarantee these will make your fan work. Not only was this heat resistor was factory installed on 1967-68 Mercury Cougar and 1965-68 Ford Mustang.Ford part # C2OA-18591-A or C8ZZ-18591-A*Note - Excludes Heater with integral or factory air conditioning.

This direct replacement resistor is used between the heater switch and the blower motor. These often fail and prevent the blower motor from turning on. Replaces Ford part # C2OA-18591-A. 1962 - 1967 Ford Fairlane1962 - 1964 Ford Galaxie1964 - 1966 Ford Thunderbird 1967 Ford Mustang 1968 Ford Mustang ...

New heater blower motor resistor for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit attaches to the heater blower fiberglass housing. Replaces part # C7ZZ-18591-B.

Used heater blower motor resistor for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit attaches to the heater blower fiberglass housing. Ford part # C7ZZ-18591-B.

Replaces Ford Part # C8AZ-2066-A Sold individually

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Retainer or keeper for door hinge pins on all 1968-73 Mercury Cougar and Ford Mustang, plus most all other Ford products with a typical door hinge pin. The factory installed the hinges with the pins driven in from the bottom as viewed with the doors installed. Most restorations install the pins from the top so that gravity holds them in. These retainers allow the pins to be mounted concours correctly. You must use a socket or other tool to install. These fit the door hinge pins with 5/16 inch...

Used rear retainer for the ignition lock cylinder on any 1967-68 Mercury Cougar or Ford Mustang. Good value, used as they come out of the cars, will have some flash rust since they were never plated or painted, usually it will not come with the small screw. This unit locates and maintains the angle to the dash from behind. Attaches with one small screw, and the bezel and retainer nut secures the whole works to the dash from the front. 1967-68 Mercury Cougar and Ford Mustang. 

Used rear leaf spring retainer for 1968 -73 Mercury Cougar with standard or non-GT / non- competition handling suspensions. Additionally it fits most 1966-70 Mercury Comet / Montego, 1970-71 Ford Torino. Identified with a stamped number "6" on the top. The inside height is 1-3/4 inches. Sold individually, one for each side for a total of 2 per car. Bead blasted for pictures, most will ship 'as removed'. This suspension part never came painted, there will be some erosion due to...

Push on retainer for rear drum brakes. 2 or 3 of these were used to hold the rear brake drums onto the rear axle assembly during construction of your 1967-73 Mercury Cougar or 1965 - 73 Ford Mustang. While not necessary, these are a neat concours item. Sold individually.  Ford part number 372188-S

Cougar actually used a larger ribbed plate on manual transmission cars without a console but this Mustang part is an inexpensive alternative. The rubber shift boot screws to the transmission tunnel, carpet then goes over it and lastly this retainer slips over the boot and hides the cut edges of your carpet. Shift boot sold separately.Replaces Ford Part #: C5ZZ-7262-C.

Nice reproduction clip for attaching the speedometer cable onto 3 and 4 speed 1967-70 Mercury Cougar and Ford Mustangs. Mounts to the firewall.

Used steering column tube retainer for the 67 - 69 Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. These little units help hold the steering column together and there are 3 required per column. Sold individually. This are not advisable in the 1970 and later cars. Ford part # C7SZ-3499-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Reproduction lower ball joint retainer and gasket. Works on 67 - 73 Cougars and Mustangs.

Reproduction retainer clip for the back up light switch wiring on the 67 - 69 Cougar or Mustang equipped with a 3 or 4 speed transmission.Replaces Ford part number C7ZZ-14163

This reproduction clip secures the clutch pedal rod end as it comes through the clutch pedal hanger.  Keep in mind that this reproduction is a different size compared to the original (see comparison above) and will need to be modified to make fit. As always, we recommend going with original used parts. You can find it here. Replaces Ford part number C8AZ-2B277-A ...

Plastic insert with metal locking retainer. Replaces Ford part # C5AZ-6221952-A. NOTE* This clip will need to be squeezed on the clip side in order to obtain a good grip. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Reproduction emergency / parking brake retainer clip set for the Mercury Cougar or Ford Mustang. These units are sold in a set of 3.

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...